Tried some new music to mix it up. Let us know if it’s something you like or if we should stick with the old music

Just myself and a nephew put my bed back on during restoration (8 ft bed), and this triggered the PTSD from that event. The only lift we had were 4 arms, 4 legs, and two damaged spines. ;) A quick tip: If you ever have to replace the fuel pump, you dont have to remove the bed. Just remove the left side bolts, loosen the right side bolts, and with a twoo foot long 2X4 (use the wheel well) and a floor jack, you can lift the bed enough to get to the fuel pump with little effort.

I absolutely love your series with this old Chevy 1500. Great truck and great work plus explanations!

I need to move the bed back so I can weld new cab corners. Thanks for the help.

so glad i found this channel I'm working on my 98

Always enjoy the content. You got me switching out my steering shaft this week lol

Makes me really wish I had a lift! Great video. Made it look super easy! Thanks yall!

Thank you . Doing body work on my 96 k1500 an this helped a lot. !

Excellent! Viewed many for replacing fuel pump. None had a tow-bar!!!!! All relied for camera work on ground access, so far from clear. Have lift but occupied by 71 Olds Delta88 Convertible , using engine hoist for bed removal. 2000 Silverado 2 wheel drive, short wheel base, WITH tow bar.

Brings back memories of working on replacing the fuel pump in my 1989. I seriously considered cutting out an access panel in the bed in the event of future maintenance to the pump and avoiding this 😂 never again.

I thought I had it nice having a tractor to lift it off. That lift is awesome!

Well done straight up tutorial thank you

Thank you for the video.. 👍👍. Liked and subscribed!!.

Thanks for sharing this video! Will be restoring my 98 OBS Chevy soon on my channel. New Subscriber!

I always get super jealous watching people work on their vehicles who don't live in the Rust Belt.

man that shit looks so clean ngl 😭 my 96 bed frame is rusted tf uo

Easy to do if it hasnt spent its entire life up in the rust belt like my 96 has😂😂either way, great video👍

Thank you buddy

Thanks!

I appreciate the video but how many guys have the right fancy equipment like yours. Santa didn't bring me a box hoist.

How did you Jss do them with hand tools the ones at the back I can’t with a power tool

Removing the bed off my 89 GMC Sierra. Watched a lot of your videos and a few others. I'm having to do this in my driveway and do not have a lift like yours however I'm told incident videos where it's done with a crane / cherry picker 1 ton hoist. My question is this, none of the videos that I've watched show how they are attaching the straps inside the tie-down pockets. Is there a certain eye bolt that you used or did you just run the straps through the holes? Some people have said that picking the bed up that way could possibly cause the outer panels to bend inward. There are some videos where people actually build an H-shaped steel frame that fits inside the bed and under the inside bed rails to lift it, but I don't have the steel or welding equipment to build one of those and my concern with that would be if it would slide out from underneath the inside bed rails when lifting the bed if it were to tilt. Could anyone please make a video or at least explain what you used or how you tied the straps down in the pocket tie downs of each corner?? Thanks

Are the bolts that hold the Bed to the frame,, are they metric or Unc thread,, someone has taken mine off and lost the bolts and the threads in the bed look damaged.. Steve in Australia

Is it possible to slide the bed about 6 inches to a 1 foot or will the fill up tube be in the way? Thank you for your time.

Okay I have a question I have a 1994 K 2500 with the 14 bolt full float in the rear it has 410 gear ratio in the rear what do you think you would have in the front 4:10 4:11 or 4:09

Some Thrust Boys music

Do you have any video on how to remove the plastics inside the cab 2500?

If you love your truck, you will replace those shocks lol

Are all years '88-'1999 interchangeable?

Is this about the same for the 88 cheyene k2500s

What size socket is needed for the bed bolts ?

What did you paint that with?

Do you know what the weight of the truck bed is?

cab corners....lol

What size socket?

Oh my goodness guys, safety glasses please.

Easy when u don't have a rust bucket

There are 8 bolts not 6, good video tho !!

Bad sound on this video. Could hardly hear you.