Replacement of Ball Joint with Factory Rivets #shorts #suspension #carrepair
Пікірлер: 538
@Everythingisgoingtobealright10 ай бұрын
Old guy advice, don’t use air chisels, you’re elbows will thank you. Just replace the whole arm and move on.
@petepusinskas-bi2tg10 ай бұрын
I know about the air chisel. Painful. Used it for years.😢
@max.rod11110 ай бұрын
@@petepusinskas-bi2tg is there a consequence for using a air chisel ?
@JakeyGhost10 ай бұрын
@@max.rod111vibration white finger, or maybe white arm
@petepusinskas-bi2tg10 ай бұрын
@@max.rod111 I've used an air hammer for years doing body work. Took a toll on my elbow, constant pain. Went to work for the county doing mechanic work. It's a lot better
@carlosalbertomendezmatus53989 ай бұрын
Cinceles de aire se entiende q es con maquina y boto q es a martillazo
@Welderman00710 ай бұрын
Judging by how sharp that drill bit is this must have taken well over an hour when you could have Is removed the heads in less than 2 minutes with a grinder.
@johndowe700310 ай бұрын
Yeah but heat could ruin the temper on the part. I doubt it but it's possible
@nik-rp6uf10 ай бұрын
Клепки каленые
@engenhokas698 ай бұрын
@@johndowe7003better drill means less heat on the part. Bad drill means more friction and less cutting. Temperature in that case, has nothing to do with it, that iron has not enough carbon content to become brittle.
@NandoCesar017 ай бұрын
Cortando em X,facilmente.
@kamaz5410benz5 ай бұрын
Я за этим комментарием зашёл
@user-qh7wt6rn5i10 ай бұрын
Вообще это выпресовывается шариком от подшипника за минуту
@user-pl6pl3dt3s10 ай бұрын
Я так делаю не снимая рычаг
@universum98765 ай бұрын
_выпрессовывается_
@user-qh7wt6rn5i5 ай бұрын
@@universum9876 одни учителя кругом, даже плюнуть некуда
@KmH2o2 ай бұрын
@@user-qh7wt6rn5iплюй в учителя 😂
@lakhtaG642 ай бұрын
@@user-qh7wt6rn5iэто когда у чела высшее, а кроме как в комментах его и применить негде 😁
@GABEBASSMUSIC10 ай бұрын
This guy has real work ethic cause everyone here inthe comments including myself would just replace the whole arm
@benjaminfisheriv93409 ай бұрын
Right Ball joints are probably 20-30 bucks for both and some hardware is 5 bucks and maybe 1 control arm is 100 bucks. He’s the smart one
@1truthseeking88 ай бұрын
@@benjaminfisheriv9340you wear out your tires because the bushings in the control arem allow play ...no alignment in the world can fix that, also you run risk of sing steering control in severe moments avoiding crash or loss od stability on rain hydroplaning and ice... not to mention reduced braking ... But hey, I'm sure you'll use that money better in your next life...
@user-vm7hn6jc4b8 ай бұрын
@@1truthseeking8 Bushings are also swappable. You're making this to be an enormously bigger deal than it actually is. I would bet a significant sum that old control arm with new bushings + new ball joint is going to be exactly within spec on both camber, caster and any other significant metric. Not to mention golf 4 comes factory with swappable ball joints.
@alexcorona4 ай бұрын
My local parts stores dont even carry opel parts, how would I replace it?😂
@Anthonymvpr4 ай бұрын
@@benjaminfisheriv9340It's a Daewoo Lanos, a Control Arm is like less than 60€, this isn't US ridiculous prices. Your labor paid hour in autoshops are already a joke being so high let alone parts. lol A ball joint shouldn't be more than 15€
@jarmonemeshall806210 ай бұрын
You need a whole control arm lol I'm not doing all that because they don't pay you for it 😂
@1FiZiK-MaD110 ай бұрын
У нас в России, делают так же кирнят, не много сверлят. Потом ложат шарик от подшипника. И давят гидравлическим пресом. Вылетает на ура
@mistermuhutya258310 ай бұрын
А что потом взамен ставить? Если оригинал идет в сборе
@alex570610 ай бұрын
@@mistermuhutya2583меня всегда интересовал этот вопрос .
@fantompo_fan87310 ай бұрын
@@mistermuhutya2583аналогичный, только под болты
@fantompo_fan8738 ай бұрын
@@HowAreYouPeople а с чего ты взял что мы умеем делать бомбы?
@kirya3128 ай бұрын
@@HowAreYouPeople так на видео такой же нищий, но из страны 404)
@greengoat565410 ай бұрын
Lol just had a guy come in with an ancient AMC arm with one of these, he wanted the bushing on the other side
@bensonhedges47910 ай бұрын
“Why did my tie rod and rack ends cost me $400?!?” All you gotta do is show them this hahaha
@vtorosyn10 ай бұрын
😅
@henrynwosu62778 ай бұрын
Same experience
@simazhenzhen2 ай бұрын
are tie rods and rack ends not the same things?
@ruslan320510 ай бұрын
Просто шарик от подшипника поставили диаметром самого болта и под пресс. Очень легко
@pavelcarpeikin32292 ай бұрын
Это нужно снять рычаг,сверлом по месту быстрее,главное заточить хорошо.
@ruslan32052 ай бұрын
@@pavelcarpeikin3229 согласен . Кто как привык . 👍 Просто на видео снятый .
@maxwellpruett-ny9es8 ай бұрын
Pay close attention this is how it's supposed to be done.
@AlexSmith-gb1lw10 ай бұрын
Не поверите - на Opel заклепки с центровками идут с завода
@razerrc77810 ай бұрын
Use a angle grinder they will be off in half the time or less
@peha12837 ай бұрын
Положи шарик от подшипника подходящего диаметра заклепки и надови прессом без сверления ! Сама вылетает .
@jamescarroll588010 ай бұрын
Use cobalt drill bits with drop of oil. Expensive but worth it 👌
@opelservicekyiv10 ай бұрын
Thank you very much for your valuable advice 👍
@randybeans455110 ай бұрын
Good stuff my man, wish my mechanic cared that much
@gorand.Mala-radionica-110 ай бұрын
Ja to prebrusim na nulu i izbijem mnogo brze
@A_p_t_e_m9 ай бұрын
Я конечно извиняюсь)) но проще взять шарик от подшипника 9-10мм и выдавить эту заклепку на прессе.
@opelservicekyiv9 ай бұрын
Спасибо большое, будем внедрять 👍😀
@mozzer99911 ай бұрын
Always interesting video's - I might sharpen that drill 🙂
@opelservicekyiv11 ай бұрын
Thank you
@ruslan32055 ай бұрын
Можно шарик с подшипника диаметром болта поставить на клёпки и пресом давить . Результате шпилтка вылетит шарик продавит
@ChrisGR93_TxSАй бұрын
opel! engineering at its finest X)
@neonpinhead80796 ай бұрын
If you have a bad ball joint most likely the bushings are shot also.
@user-ck9fh4zk2g5 ай бұрын
Советский молоток 🔨 не заменит не один импортный
@jerrydawg443410 ай бұрын
We never drill those out we always just use an air chisel. Typically we do it while it's still on the car
@Laughing_Central63810 ай бұрын
Yeah
@opelservicekyiv10 ай бұрын
Oh great, I have to try it too.
@nashduff846510 ай бұрын
@@opelservicekyiv I always notch the head both ways then chisel less effort with chisel that way
@myadhdSquirel10 ай бұрын
@@nashduff8465I do something similar, I'll cut the head of the rivet with the chisel in a cross pattern. Then to the side.
@Fvck_Y0u_Sad1Q_K8 ай бұрын
I've learned that this is the only option if the vehicles lower arms are no longer manufactured or are more expensive than the labor and parts required here.
@hippiemiller10 ай бұрын
Air hammer works better
@joedso97107 күн бұрын
Get a cut blade and make a T or a cross. Chisel each quarter off. And then hammer out. Sometimes the drill bit gets burnt up or takes too long. Looks like you have a good one
@opelservicekyiv7 күн бұрын
Thank you
@MiguelRodriguez-pn7qv11 ай бұрын
Replace the complete control arm would have been a lot easier
@AskerMobile10 ай бұрын
Это дороже
@opelservicekyiv10 ай бұрын
Да, это дороже
@mikeg541310 ай бұрын
More expensive BUT you get new bushings at the frame attachments … at least on my 08 focus.
@henrynwosu62778 ай бұрын
@@opelservicekyivalmost 10times more expensive
@rarbiart4 ай бұрын
this is about repairing stuff, not just parts swapping!
@j.robertvillarreal59263 ай бұрын
You can use the brazing tip to make these cherry hot then zap them off with the air chisel. You can do this on the truck.
@RS-rm9sr10 ай бұрын
Имел форд fusion, надо было менять шаровые опоры, купил, а там оказались заклёпки, кто мог подумать, пришлось срезать заклёпки шлифовальной машинкой, не снимая рычаги.
@felipealfredodeblasiramire70919 ай бұрын
En argentina Chevrolet era una de las fabricas que remachaban las rotulas a los brazos inferiores de la suspensión de las c10 no se si otras fabricas lo hacian pero era un trastorno para sustituir las rotulas despues se montaba tornilleria adecuada y asi no tener que desarmar una y otra ves pero ahora que lo pienso? quien tenia una remachadora de ese tamaño? solo fabricas y creo que lo hacian asi por una cuestion de costos, un remache vale menos que un tornillo de acero arandelas y tuercas autofrenantes , si , debe haber sido por eso ,saludos
@opelservicekyiv9 ай бұрын
Muchas gracias, fue interesante eso en Argentina con autos. Estás muy lejos. 😀👍
@BigDipper796 ай бұрын
That’s how it’s supposed to be done. Great job.
@opelservicekyiv6 ай бұрын
Thank you very much
@toomuchdrip905410 ай бұрын
So this is how you replace a balljoint? Now I'm worried that this isnt possible at home 😂
@MtnBadger10 ай бұрын
I've done a ton of those over the years, it's cheaper/faster for the factory but a pain in the ass for us. 😊
@brute68968 ай бұрын
man I'm so glad my Corolla only has bolts connecting the arm to the ball joint so don't have to replace both at the same time
@carlosmorenoyanez606 ай бұрын
I will better ask, why it doesent come with screws from factory?
@brt-jn7kg3 ай бұрын
Better way of doing that is take a cut off wheel cut an x on all three rivets then take an air hammer and it'll just slide the top of those rivets right off then you just poke them out put in the new ball joint
@fedyakunafin516527 күн бұрын
Есть ещё лучше вариант, купить новый рычаг с шаровой опорой и не заморачиваться с этим😂
@krab___11 ай бұрын
Пресс и подшипник!!!!
@user-wm2gf3dd1j10 ай бұрын
Это слишком по русски😅
@weakhohol92946 ай бұрын
И пневмозубило ещё... И болгаркой крестик... Насколько нужно быть тугим, чтоб вообще лезть к сверлу, это такие крайности
@Trurosrvboi4_YT8 ай бұрын
Tbh we just change the entire arm, because when the rear bush needs replacing the new arms mostly come with a new ball joint anyway
@johnytszcinco10 ай бұрын
Dude all the time and labor could’ve been saved by buying the whole arm
@daveeaston610710 ай бұрын
Hit that with an air hammer and chisel and they pop right off
@krislink176110 ай бұрын
I use a grinder. Mostly because my air compressor isn't large enough to really supply enough air long enough
@selwyn13Ай бұрын
Cudos to this dude. If it was me i would've gotten hella frustrated then crack under pressure and given up.
@opelservicekyivАй бұрын
thank you friend 👍
@Nycorexti9 ай бұрын
Easier and likely cheaper to swap the entire control arm. Drilling these take an absolute eternity, in my opinion using an angle grinder works best. Hard part is when half the rivet gets stuck to the control arm!!
@opelservicekyiv9 ай бұрын
totally agree, it's about saving money
@emilmuhrman6 ай бұрын
30 vs 300 $
@MrVozich2 ай бұрын
Эти заклёпки прессом легко выпрессовываются
@Alexander_l3224 ай бұрын
Grinder! You can get all three at once and it goes quick
@macarenomoranas10 ай бұрын
Lo bonito al taladrar es ver las dos virutas saliendo parejas de los dos labios de corte de la broca. En el video sale polvo y eso es que no corta bien, ni con lubricacion ni sin ella.
@johndoe815.10 ай бұрын
In the meantime wasn't nothing wrong with the first set of rivet's
@user-ts8zc2xy9b2 ай бұрын
Можно было с помощью обычного шарика от подшипников и пресса. Сам не раз так делал и делаю до сих пор
@user-qr5nv4rb8j3 ай бұрын
Шайбочки хорошие получились😊
@andrewbanit48846 ай бұрын
Can also use a part of ball bearing. Накернил вместо сверла ложешь стальной щарик от подшипника меньшего размера и ложи на пресс и дави его. Саерлить не надо меньще пыли и быстрее. This trick works very good for me
@opelservicekyiv5 ай бұрын
Спасибо, надо попробовать с шариком
@metalsurgeon919610 ай бұрын
Why bother you've got the whole control arm out. Replace it. You get new bushings and the ball joint. That repair can be made on car.
@elroyleewildcatwildcat31314 ай бұрын
They sale the hole arms.. and Ball joints at Napa auto parts 👌👍
@user-of9gi6gv4s6 ай бұрын
Подшипник нужного диаметра и пресс,и бут счастье.
@serial.3607 ай бұрын
paid by the hour looks so much more fun
@user-od3cv3ki6c9 ай бұрын
Не,этим хватает шляпки срезать,керна хватит,то же на Ситроен было каком то,а вот с Фордом ток не проканает...😅
@Hazi_Aslanov6 ай бұрын
Меняю всю руку, так с завода заклепками идут и по одному не надо что то менять, поменял комплект и живешь пару лет без проблем
@opelservicekyiv6 ай бұрын
все правильно
@TheFedosV10 ай бұрын
Все это проще делается болгаркой запиливается крест на заклепки потом Так же зубилом сбивается заклепка мягкая а вот работа со снятием рычага доя того чтоб ремонт был дороже
@jag45207 ай бұрын
Use the press on the other side and open below the bolts! Two pieces of metal leaving space them to drop!!! WTH!!! You already took off the arm anyway.
@user-pd4ll8ew8m6 ай бұрын
Как все долго .. покажите ему болгарку … углошлифовальную машинку
@Jurgy7778 ай бұрын
I liked the part when he replaces the ball joint.
@opelservicekyiv8 ай бұрын
Thank you
@user-hx3kz3in9i10 ай бұрын
А про прес и балгарку забыли))))
@davidcoupalbergeron26 ай бұрын
Where you found the same ball join ? After you need to make it red hot with the hamme ?
@downtoearthconstruction77688 ай бұрын
In the rust belt they never punch out that easy
@user-pz6ml6wk7x6 ай бұрын
Шарик металический на центр заклепки под низ головку и под пресс 100%вариант
@opelservicekyiv6 ай бұрын
Ок, спасибо, будем пробовать👍
@StevenPerez-ge9ch10 ай бұрын
Just buy the lower control arm and ball joint 😂😂😂....nice video
@opelservicekyiv10 ай бұрын
Thank you
@user-ie5jy2rh1yАй бұрын
Нужен пресс и рука маркетолога,что бы на болтах не экономили😂
@opelservicekyivАй бұрын
😊
@PeuSHINIGA2 ай бұрын
Meanwhile during this car development: - "You're gonna use rivets to fix this ball joint? What about maintenance?" - "I'm a engineer, not a mechanic, each one with your own problems..."
@opelservicekyiv2 ай бұрын
That's for sure 😊👍
@keithshort4218 ай бұрын
I usually cut an x with a cut off wheel and then use my air hammer has the whole thing done quickly!!
@rowaidasmael37710 ай бұрын
Bro, new wish bone and less money, quick 10 mins in and out and on to the next
@user-vm6su5py6f10 ай бұрын
Вообще все неправильно. Можно достать легко!Ничего не повредив.! Аккуратно и быстрей.
@VinDieselS708 ай бұрын
6 months later the bushes need replaced. Yeah, we're replacing the arm with a new ball joint on it.
@aleksandrsolopanov817 ай бұрын
Лишних действий, шарик от подшипника и пресс. Секундное дело.
@fosforexeАй бұрын
At least he knows whats doing
@L3004-410 ай бұрын
Шарик от подшибника нужного диаметра ложиш и под прес вылетает как её и небыло там
@nastarship890310 ай бұрын
And if your control arms look like that and the balljoint was bad how good do you think the rest of the bushing could possibly be??? Just change the damn control arm
@mattd11882 ай бұрын
If the whole arm is available, just go that route.
@supersidecar890110 ай бұрын
Drilling steel... sharp bit, High pressure, coolant and low rpm.
@jessejuliano533610 ай бұрын
You do realize it probably only pays 1.0 hours to R&I that ball joint, right? We use an air hammer with a chisel bit and do it right on the car
@Chopped93VX10 ай бұрын
I had to do this process almost exactly on a Pontiac Aztec. worst experience on a lower ball joint job I've ever had
@YU-ic1cw10 ай бұрын
Aztec?? Really.? Just but a $100 control arm. A "days worth of work" saved.
@Chopped93VX10 ай бұрын
@@YU-ic1cw it was a favor. Guy already had the part.
@RS-rm9sr10 ай бұрын
На форде тоже также, инженерам безразлично как вы будете заменять деталь
@user-ci5kv1tg7l10 ай бұрын
В прес ложиш, сверху шарик. И всё вылетает аж бегом без всякого сверления.
@opelservicekyiv10 ай бұрын
Будем теперь только так делать
@anthonyrivers839510 ай бұрын
Surgical precision
@Sashka78619 күн бұрын
болгаркой режешь шляпку на 4-6 частей и сбиваешь зубилом, не снимая рычага
@opelservicekyiv19 күн бұрын
отличный вариант 👍
@Vasiliy1987god2 ай бұрын
Я в прессе выдавливал эти клепки сверху шарик от полшипника с нихюзу обойму
@user-oe6ew6pm3n10 ай бұрын
Кладете посередине клепки шарик от подшипника и давите прессом, за минуту все готово!
@opelservicekyiv10 ай бұрын
Спасибо, будем пробовать
@JoeMamasLover6911 ай бұрын
I must know why it the hell do they do that to the ball joints and how many hours do you get off that? I assume you do an alignment after?
@opelservicekyiv11 ай бұрын
20 minutes, wheel alignment done
@AskerMobile10 ай бұрын
Замена изношенного шарового шарнира на новый.
@user-rl9sd3gd9u10 ай бұрын
Режу болгаркой крестом,срезаю пневмозубилом.на много быстрее но шуму больше.
@RealDeal4585 ай бұрын
These are not as easy as it looks I promise I’m stuck doing this right now
@odivansecretario10 ай бұрын
Uma Esmerilhadeira com disco de corte , eu uso no lugar da furadeira e bem mais rápido ! Depois uso um rolete de rolamento e levo na prensa!
@fasfgasdfagadsf10 ай бұрын
Man, I hate to inform the customer that they paid twice what a new control arm cost.
@johndowe700310 ай бұрын
Why would they pay double
@PWgadgets10 ай бұрын
@@johndowe7003 Labor
@johndowe700310 ай бұрын
@@PWgadgets looks like polish or central European. Labor is cheap there also
@lv760310 ай бұрын
Labor costs are not the same around the world that’s why in some countries they still repair stuff rather than just replace.
@Dutchtheyooper10 ай бұрын
I use a grinder or replace the whole arm
@gunztommiegunz8 ай бұрын
Air hammer and be careful not to damage the control arm but TO EACH, HIS OWN
@opelservicekyiv8 ай бұрын
Ok, thank you
@jesusyeshuaelelyonelshadai62959 ай бұрын
This is good😮 i usually use a airhammer and chissel to cut off rivets but if no air available this is very 👍😮😅
@opelservicekyiv9 ай бұрын
Thanks a lot 👍😀
@customworksgarage371710 ай бұрын
Не снимая рычаг все делается,10 минут потолок.
@elgroso8065 ай бұрын
That's the long way... No drill needed. Just an air hummer with a chisel
@danielking22110 ай бұрын
Do your self a favor and wear gloves. They help save your hands from the shock of hammering.
@opelservicekyiv10 ай бұрын
Thanks a lot. We will definitely do it. Thanks for the good advice friend ! 👍😀
@romanrodyukov35036 ай бұрын
Что вы делаете!!!! Зачем столько лишних операций????? Возьмите шарик от подшипника подходящего диаметра к клёпке и выдавите в пресе, 3 минуты работы
@opelservicekyiv6 ай бұрын
Ок, спасибо, попробуем шариком
@bolo3274Ай бұрын
Załóż rękawice ochronne, szkoda rąk.
@Mega_volt219 ай бұрын
А если сверло наточить, то работа пойдёт легче и быстрее
@opelservicekyiv9 ай бұрын
спасибо,ок
@user-fm5kj4ki3e10 ай бұрын
Очень долго. В прес маленьким подшипников 3 минуты и всё готово
@johndillinger26566 ай бұрын
Необдуманные действия и их последствия. +1 испорченное сверло