In this video I strip down the clutch side of my 2021 Yamaha Mt09. I checked it over to see if there is any room for improvement or if there was anything wrong with it.
Пікірлер: 31
@nikkibreayley7075 Жыл бұрын
Nice and simple, gj
@TheMotorcycleForge Жыл бұрын
Yeah that was the goal
@chipwood674 ай бұрын
Hi mate I know you have sold the bike.. But do you recall the clutch arm and dot alignment after install off the clutch cover were in alignment dot to triangle.. Before you pull the clutch lever in.. On mine Gen 3 22 Europe plate.. The dot to triangle are off set and only are aligned once clutch lever pulled in.. Gen 1 was aligned dot to dot before clutch pulled in.. I've been told Gen 3 is the same.. Just odd.. Europe - US thing I don't know.. Thanks
@TheMotorcycleForge4 ай бұрын
No sorry I don't recall, was quite a while ago.
@chipwood674 ай бұрын
OK thanks anyway
@rockerzaki8877 Жыл бұрын
Did you drain a motor oil before this action?
@TheMotorcycleForge Жыл бұрын
Yes I did drain the oil.
@yaitstac7267 Жыл бұрын
You don’t have to
@TheMotorcycleForge Жыл бұрын
I was doing an oil change at the same time.
@aktashuseyin9 ай бұрын
ı got fz 09 with noisy clutch. So its a problem without solution ?:)
@TheMotorcycleForge9 ай бұрын
I would check the release bearing if it's excessively noisy but unfortunately these Yamaha triples seem to have above average clutch noise factory.
@p0c0d.t3 ай бұрын
Replace the clutch damper, its the last thing that he removed, that basket thingy just before the clutch bearing. It's the main cause of the noise.
@fabienbable Жыл бұрын
Did you change or replaced something? If not, why the job?
@TheMotorcycleForge Жыл бұрын
I thought the clutch bearing sounded noisy but couldn't fault it and I thought it would make a interesting video that might help someone who wants to do a clutch or bearing themselves.
@robertdean81028 ай бұрын
Thanks for sharing this video
@jbroadbelt6Ай бұрын
That's the hallmark sound of mt 09 clutches.
@slowridefpv966813 күн бұрын
Lol, I have a 2019 and a 2021sp. The 2019 makes a fair bit of noise, runs great clutch feels fine. Noise isn’t so bad after a few minutes of riding.
@slowridefpv966813 күн бұрын
One last comment, didn’t notice the noise coming from the clutch area until I switched to the Yamaha synthetic oil? Probably going back next oil change.
@chipwood674 ай бұрын
Just to add I have 2022 model 4000 miles bought from dealer Sat in garage 6 months first test ride serious clutch judder feathering the clutch out from standing start.. Once moving the clutch is OK.. Dealer said slipper clutches do that.. Absolute rubbish... How's yours standing start... Odd thing is I bought Gen one 16 plate same thing scenario sat in garage 6 months before test ride judder again.. Had new clutch plates put in and friction plates on 16 plate problem gone away.. Now I have to do the same thing on 22 plate what's the odds.. Or maybe couple off plates sticking on 2022 plate.. This time take out and clean or £450 to refit new seller says bring it back to look at it 600 miles trip😢.know chance.. How does yours feel standing start...
@TheMotorcycleForge4 ай бұрын
Yeah it shouldn't do that, mine was super smooth taking off from a standing start.
@chipwood674 ай бұрын
OK thanks but do you have any options on what it could be.. Cheers
@TheMotorcycleForge4 ай бұрын
Possibly warped or unevenly worn clutch plates would be my guess.
@chipwood674 ай бұрын
OK cheers mate.. Please could you do me one last thing.. I noticed today my dot and arrow on the clutch case cover and clutch arm lever.. Are offset when clutch is not pulled in.. they only line up when I pull the clutch lever in.. Is your Gen 3 the same.. Odd thing is my Gen one 14 one plate we're lined up correct and offset when clutch pulled in same on Gen 2 17 plate as Gen one.. Just Gen 3 I have Gen 2 22 plate.. Just seems odd.. Thanks for any help..
@TheMotorcycleForge4 ай бұрын
Unfortunately I have sold my mt09 since I made this video so can't help much with that question.
@cbdarius Жыл бұрын
What socket size for shaft nut?
@TheMotorcycleForge Жыл бұрын
I think it was maybe a 27mm from memory
@abe_sm8 ай бұрын
Bro forgot to oil his clutch before putting it in
@TheMotorcycleForge8 ай бұрын
Bugger that's not good
@Sk00bs878 ай бұрын
put bike in gear hold rear brake nut off
@TheMotorcycleForge8 ай бұрын
Tried that twice, defo a no go. Nut was f**king tight