Reset the ABS, VSC and Brake system warning lights on Toyota Prius.

Рет қаралды 281,125

3 жыл бұрын

A diy, step by step video demonstration on how the ABS, VSC and Brake system warning lights were reset on 2008 Toyota Prius.
Please Subscribe: / @tryadaptlearn
Donations: ko-fi.com/tryadaptlearn
Donations to TryAdaptLearn via Ko-fi are greatly appreciated
#Prius #resetlight #resetabslight #resetvsclight #resetwarninglight #abslight #vsclight #warninglight #toyotafortuner
This is reset procedure only, if indicator lights keep coming on after they are reset the problem is likely still occurring.
Take the vehicle to have a Toyota and/or ASE technician with diagnostic tools to run through the ABS and braking system.
If you must troubleshoot yourself, next steps would likely be to check:
Computer maintenance codes
Electrical fuses
12 volt battery voltage
Brake fluid level
Brake pad/shoe wear
Continuity of wires to the brake system sensors
Faulty sensors
ABS pump and/or actuator
In this video a jumper wire from an electronics kit was used. Others have used a paper clip as the jumper. Any wire with a small enough gauge would lead to similar results.
Tools that may help troubleshooting issues like this:
Jumper Wire Kit 140 Piece
amzn.to/3Z0bExR
Klein Tools MM325 Multimeter
amzn.to/3PuHVKF
Thank you for your support:
Your donations will help to support TryAdaptLearn
ko-fi.com/tryadaptlearn
Subscribe now to TryAdaptLearn: / @tryadaptlearn
View other videos on this channel.
Comments and likes are welcomed and will also help support this channel.
Our other channels:
www.youtube.com/@TryAdaptLear...
Disclaimer:
This video is for demonstration and entertainment purposes only. All viewers must take responsibility for their own choices and actions. The creators of this video and anyone recorded in the video are not responsible and do not assume any responsibility for all purchases, damage, injury, death or dismemberment resulting from the performance of any operation in this video. Use the proper parts, specifications and safety procedures for your own application.

Пікірлер: 166

@galaxy8818 3 жыл бұрын

Hi. Thx for your video. I have same problem. Lights goes off but when i take clip out the light come backs on. Any advice pls

@TryAdaptLearn 3 жыл бұрын

If indicator lights keep coming on after they are reset the problem is likely still occurring. Take the vehicle to have a Toyota and/or ASE technician look at it, They will have the diagnostic tools to run through the brake system thoroughly. If you must troubleshoot yourself, next steps would likely be to check: Computer maintenance codes Electrical fuses 12 volt battery voltage Brake fluid level Brake pad/shoe wear Continuity of wires to the brake system sensors Faulty sensors ABS pump and/or actuator

@galaxy8818 3 жыл бұрын

@@TryAdaptLearn . Thx for your reply.

@galaxy8818 3 жыл бұрын

@@aimlessdrive8723 I took it to garage they had expensive scan tool they clear it was easy, but with my scan tool didn't work

@JohnD-or9py Ай бұрын

Thanks for the video 👍🏼 Just a quick note for those who don't want to bridge the OBD outlet.. The same diagnostic mode can also be activated by holding the display button and turn the light on and off three times There's a bunch of videos out there how to do it

@javihia21 11 ай бұрын

Thank you very much or the clarity on this issue. I just replaced the wheel bearing hubs on the front end of my 2009 Prius, and this caused these brake warning lights to come on. Knowing that I do not have any other issues with the brake system this was all I needed to do. Thanks again, I will be hitting that follow button to see more of your content!

@TryAdaptLearn 11 ай бұрын

Glad to hear that the process worked to reset the lights in your cat. Most of the time, the lights indicate an issue but sometimes like your vehicle, they just need to be reset. Thank you for your support.

@dallasholland3696 3 жыл бұрын

I did my own brakes on my 2009 Prius and the brake, ABS and VSC lights came on and braking was unacceptably dangerous. With a PAPERCLIP and jumping the pins like your video shows, my brakes now work like a dream and all of the lights are off. Thank you!

@TryAdaptLearn 3 жыл бұрын

I am glad it worked for you. This is likely because you solved the issue by with replacing the brakes and the reset procedure was just for the lights.

@meistermd7229 11 ай бұрын

Same for my 2008 Prius! Need to pump the breaks 8x when the diagnostic screen came on like another post said. Classic KZfaq at its best right here

@20891 5 ай бұрын

@@TryAdaptLearnI did it but it comes back like everyone 5 -10 miles . Do you know the solution to that ?

@markwilliams3140 2 жыл бұрын

2009 Prius, recently had left front wheel bearing assembly replaced. When I started my car afterwards, noticed "Brake, ABS, & VSC" lights stayed on. In your video you mentioned "connecting jumper wire 5th hole on top 4th hole on bottom". I stopped the video and noticed holes connected were opposite "4th hole on top & 5th hole on bottom" and that's where the jumper wires were placed. Today used a small paper clip & after a few times trying to connect jumper wire (4th top and 5th bottom), at 66 my eyesight is not like it used to be, had to get real close, and finally got them connected. Turned car on, diagnostic screen popped up(all o.k.), pumped brakes 8-10 times real fast, and brake light went out, other ones were still flashing. Will go down tomorrow as I ran out of daylight, and do again as I left the jumper wire connected. Thank you for the video! It was a big help.

@TryAdaptLearn 2 жыл бұрын

Thank you for your feedback and good luck with resetting the rest of the lights.

@markwilliams3140 2 жыл бұрын

I do appreciate your video. Very helpful!. Have made several attempts to clear the remaining lights on 2009 Prius with 202,000miles on i.When I start the car and remove paper clip, the mentioned lights(ABS, VSC & exclamation point) remain off, but when I start down the road, within a minute or two they come back on. So I suspect a defective/damaged Speed/ABS sensor. Will be checking associated fuses tomorrow. My son last week changed my left wheel bearing hub assembly, so something might have happened with the mentioned sensor. I di find your video very helpful. Thank you!t@@TryAdaptLearn

@markwilliams3140 2 жыл бұрын

Well tried several times using paper clip method per your video. Lights on dash would be off while car was not moving, but came back on after going down the street. Checked fuses..all fine, even unhooked 12v battery for 10-15 minutes. This morning was pushing dust shield away from left front rotor, was able to reach my hand in behind brake rotor, lo and behold found the left front wheel sensor unhooked. Took car over to my son, he pulled the wheel off, and found the little bolt holding the sensor in place had been sheared off. Were able to remove remaining threads, and secure the connection. Started the car and all the same lights were back on, so got out my trusty paper clip, and did the process again, removed paper clip (lights again off), drove a little piece up the road, lights did not come back on. I drove about 15 miles home, lights are still gone. Thank you again for the video, after doing it several times, was able to memorize the process. Problem is solved.

@jayskrills7375 Ай бұрын

@@TryAdaptLearn you definitely said It wrong

@Afroshume 4 ай бұрын

Thanks for powerful information

@GaryMarkowski 2 жыл бұрын

To reset the internal DTC codes for ABS, while displaying this diagnostic screen, press and release the brake pedal 8 times within 5 seconds. Turn the car off, remove the jumper wire, and start the car. Note: for me, I think the error was triggered when I had some brake fluid come out of the cylinder when replacing the rear brake shoes. I adjusted the rear brakes, and bled the brake lines to get the air out of the lines, and then cleared this error. It worked! For me the ABS code was 42 and the VSC code was 65.

@TryAdaptLearn 2 жыл бұрын

Thank you for your detailed description. One good thing is that you added the reason why your light came on and how you fixed it prior to resetting the light. There are many reasons why these specific lights come on for this vehicle. First assumption should be that the lights and sensors are working and there is a malfunction in those systems. Your comment explains your issues clearly.

@johnnyovermind9830 2 жыл бұрын

Lol you answered my the question that the video didn't

@danielroytanked2375 Жыл бұрын

Thank you, I had diagnosed and fixed my brakes without the fancy scan tool and just needed to do this 🤣

@Afroshume 14 күн бұрын

Thanks for great information

@user-qp4gd2tv8z 5 ай бұрын

I don't really comment on here but this really works. Thanks. I did what others have comment about pressing the breake 8 times within 5 seconds. So not sure if will work without that

@Afroshume 3 ай бұрын

Thanks for helpful information and save life especially today Colorado today storms thanks again

@Afroshume 4 ай бұрын

Thanks for great information this advice saves money and life

@jorgemora7190 13 күн бұрын

Wow try. Dry good job tahnks for your inf we always learne god bless you

@Afroshume 3 ай бұрын

Thanks for life saving advice and save money

@Afroshume 3 ай бұрын

Thanks for helpful advice and save even life and money

@Afroshume 4 ай бұрын

Thanks sir for helpful information because this kind free information saved money and stop hard working people keep on daily activities thanks again

@Afroshume 14 күн бұрын

Thanks for information

@Afroshume 3 ай бұрын

Thanks for powerful information even save life and money

@Afroshume 2 ай бұрын

Powerful information for save life even save money thanks

@Afroshume 2 ай бұрын

Thanks for saving life information

@Afroshume 3 ай бұрын

Thanks great advice because this information important for save life and money thanks again

@marcrgarcia 11 ай бұрын

Thank you, it worked for me!

@TryAdaptLearn 11 ай бұрын

Good to hear you were able to reset the lights.

@TBSWORLD77 Жыл бұрын

Awesome video thanks!

@TryAdaptLearn Жыл бұрын

Thank you for watching and leaving feddback.

@naseemawan457 4 ай бұрын

Thanks very informative video

@Afroshume 3 ай бұрын

Thanks for helpful message because even save life and money

@THOTH36944 2 жыл бұрын

This worked for me after changing my battery but i also had to press the brake pedal 8x within 5 seconds as mentioned below by Abe Alexander for it to clear my code, so that method works for 05 and 09 base model for sure.....After changing my brakes, lights came on along with breaks barely working, I had to put car in battery mode while using the break to help car stop, this method fixed it so yea thanks a ton 👍🏾

@TryAdaptLearn 2 жыл бұрын

Awesome. Glad it helped to reset the lights. Thank you for leaving feedback.

@RemygaVTaurage 2 жыл бұрын

fixed my 2011 Prius lights , when press the brake 8x within 5 seconds !

@bruceprigge5212 2 жыл бұрын

Thank you! :)

@TryAdaptLearn 2 жыл бұрын

Thank you for your feedback.

@giopirmisashvili5514 26 күн бұрын

Thank you

@Afroshume 3 ай бұрын

Powerful advice for people especially they don’t know about cars because is gene save them money even life probably all family life

@rafayzq Жыл бұрын

Worked perfectly. The lights came on after i replaced the drivers side hub. The brakes were not working and the lights were on. I entered the diagnostic mode by using the jumper cable and just to be sure, pressed the brake pedal 8 times. Worked on the first try. Brakes are back and lights are gone.

@TryAdaptLearn Жыл бұрын

That’s great it worked as a light reset for you. Thank you for leaving your feedback.

@danno58a 2 жыл бұрын

Worked perfectly. Thanks!

@TryAdaptLearn 2 жыл бұрын

You're welcome and thank you for the comment.

@davidtobi7497 3 жыл бұрын

Thank you I am gonna try this hopefully works out fingers crossed

@TryAdaptLearn 3 жыл бұрын

You're welcome and good luck with the warning lights.

@JonEhBee 10 ай бұрын

I just wanna point out that if you have an airbag light, check the wiring under your seats. My wiring was mangled af. I fixed the wiring (not condoning diy repair of abs and srs wiring) and the light went out on its own.

@TryAdaptLearn 10 ай бұрын

Thank you for sharing this information. There are a lot of systems that may use the same indicator lights and it’s good to learn about one more area to check and troubleshoot.

@TheNorthernMist Жыл бұрын

Thank you!

@TryAdaptLearn Жыл бұрын

You’re welcome. Thank you for leaving feedback.

@Afroshume 3 ай бұрын

Thanks for life saving information because this code thing scary if you don’t save it save area thanks again for information and even save money and life

@tunercar652 2 жыл бұрын

Guys make sure you check your speed sensor is clean and the dust caliper is installed correctly. That’s what caused my lights after a bearing change.

@TryAdaptLearn 2 жыл бұрын

Thank you for your perspective. A dirty connection at the sensor is one only few issues that may be the cause of the lights displaying without any serious issues with the parts or systems.

@AbeAlexander 3 жыл бұрын

You missed an important step. You are supposed to press the brake pedal at least 8 times within 5 seconds once the diagnostic screen appears. Without this step it did not work on my '05 Prius. And this is directly from the Toyota service manual on page BC-38 (Break Control section pg. 38)

@TryAdaptLearn 3 жыл бұрын

Thank you for including this information. The process in this vehicle worked for the vehicle in this video but the steps in the Toyota service manual (and/or manufacturer service manual specific to each vehicle) include the proper and definitive process.

@THOTH36944 2 жыл бұрын

@abe Alexander thanks for the Info It works for a 09 prius base model....

@user-yx2mc9vm6x 2 жыл бұрын

Worked for me after pumping them 8 times. Ty for the help

@marcialvalladares7671 2 жыл бұрын

It Works in my Prius 05

@Muttt13 10 ай бұрын

Thank you, wasn’t working for me on an ‘07 until I did this!

@AbdulRahman-yq6pm Жыл бұрын

If this doesn't work, please check your brake fluid level. It was actually my problem and, thank God, just by adding some fluid all the lights went off.

@TryAdaptLearn Жыл бұрын

Thank you for contributing more information to help troubleshoout this issue.

@gianave Жыл бұрын

Just as Abdul Rahman, in my case too abs, vsc, brake system warning lights went all off after adding more Brake fluid. The diagnostic sw confirmed error C1202 "insufficient brake fluid". When I checked though, the level was on MIN and could not suspect this to be the cause.

@shellyriley4607 15 күн бұрын

I have replaced both the pump and the brake booster and master cylinder. My mechanic did not have the diagnostic tool to recalibrate the software to reset the lights. Any advice how to recalibrate my system to get the lights to turn off after replacing the entire brake system? After replacing the brake system, there are no diagnostic failures reporting on a scan tool.

@Sunnysky321 Жыл бұрын

Great video. My 2012 Prius C shows the same warning lights. Do you happen to know which pins (and their locations) so I need to jump?

@TryAdaptLearn Жыл бұрын

I'm sorry, I do not know if this prodcedure will work on the nwer Prius C. I would start to troubleshoot the issue with a code reader.

@gustav3795 8 ай бұрын

I’m new to your channel, looks like good advice so I subscribed. Do you have a video on why none of the dash lights come on, or even the infotainment module and the key has to be in the ignition at this point to turn on? I have an 09 Prius. Thanks 1:21

@TryAdaptLearn 8 ай бұрын

Sorry, I don’t have any other videos for the dash lights. In normal operation the lights should come on then go off. If the infotainment module is not on then the display could be damaged and/or a more serious issue. If the dash lights and infotainment are all off, it may be time to have a second person to help troubleshoot issues and/or take the vehicle to a Toyota certified technician. Sorry it’s hard for me to understand the “key” part of the question. It looks like 1 min21 seconds is still speaking about the jumper wire, if I can remember, the key was not in the ignition or on when inserting the jumper wire. This of course is no substitute for for the proper Toyota diagnostic tool to reset the lights.

@ulamiladakolo1198 4 ай бұрын

Is this method applicable to Toyota Sai.? I have the same probalem and I'm just wondering but i haven't tried it yet.

@spelunkerd 3 жыл бұрын

I've had similar warning displays when the accessory battery was on its way out (Toyota Lexus 450h). Resolved on replacing the battery, no jumper wire reset needed.

@TryAdaptLearn 3 жыл бұрын

Thanks for the info. With a bad battery being the best case scenario, it seems as though the brake actuator/accumulator would be the worst case for the brake system issues common in this generation Toyota Prius.

@lmc2375 3 жыл бұрын

I had a 6 month old tire go on me, damage caused tread fapping. I immediately stopped, got towed, had tire replaced, my Excl sign, ABS and VSC have been on ever since. Toyota said actuator system needs to be replaced, 2700. Is that bs or quite possible? I don't trust them, they never get the lights off or they come back for other past repairs. Last thing I had done was inverter control, before that was inverter. And in between those two repairs, 1 yr old blower assembly stopped blowing again. I need to pass smog, but can't lit up like a tree dash. These aren't even smog issues. Just looking for some advice before I do it bc they aldo said no guarantee they can get lights off. They just want to start replacing things; process of elimination, sounds like guess work. It's an 09', 77K orig miles. I never abuse it. I'd like to have some idea before I return.

@lmc2375 3 жыл бұрын

Flapping was meant.

@spelunkerd 3 жыл бұрын

@@lmc2375 I'd be looking for a second opinion, that's a lot of cash to put down without a certain diagnosis. Unfortunately a problem like that may require somebody with high end diagnostic skills, maybe even dealer only. By the way, if you ever want to correct a spelling error, click on the three dots to the right of your post, you'll find a tab labeled 'edit'. Make the change and save.

@lmc2375 3 жыл бұрын

Yes, it is a chunk, have it but prefer to know I actually need it, not that mechanic is only able to read code thinking replace when it could be something less involved. That's it, you just don't never really know. Thank you though. As for corrections ... I am familiar. Apparently my cell is going haywire too; not allowing edit box to pop up, hence why I just added addition. I'm in my astro Saturn Return; forced to take care of things that I didn't properly see finished, nor persisted in initial round one, like these so called repairs. I was ticked and felt if I went back, I was going to blow my own gasket in frustration. I've already paid chunks and still, did not get what I paid for. I just have to learn patience and maybe a better flow will result. Yet, I'm still doubtful : /

@kevinteodosio4397 3 ай бұрын

I tried this method and it works until I drive about 20 miles and all the lights go off again. I’m not sure if it’s safe to drive but I’ve been resetting the warning lights for about a week. No codes show up but when I went to auto zone to check the code C1391 came up. Abnormal leak of ACC press.

@Afroshume 4 ай бұрын

Thanks for information I did your advice but some reason the light comes back after few hours I feel like someone control this thing

@emmanuelhaastrup 4 ай бұрын

What type of jumper wire was used?

@MountainSpringsAdventures Жыл бұрын

This didn't work for me, the ABS and brake light is still on. The ABS and circle/! Light is flashing when in the diagnostic mode. I also pressed the gas 8 times like others said and it still didn't work. I just changed a wheel hub and brake caliper. What could be the problem? I'm pretty sure I installed the caliper correctly

@TryAdaptLearn Жыл бұрын

I am sorry to hear that the light is still on. It is likely that the hub and brake caliper could keep the light on or that there is another issue. If disconnecting the battery and trying to reset the light doesn't work there may be an ongoing issue related to these systems. I would try an automotive code scanner/reader to see if there are any associated codes related to the lights. If still in question, it may be worth it to take it to a Toyota dealership with certified Toyota technician/s to properly diagnose the braking systems.

@Hubjeep 3 жыл бұрын

Will this work with a 2012? Ever since having a low tire my "slip indicator light" has been on! It's the only light on. EDIT: Our Prius-V is a 2012 and still has original 12v. Trunk battery!

@TryAdaptLearn 3 жыл бұрын

I’m not a technician but here’s my opinion on what I would do if this were happening: Several issues are challenging so I try to do as much as I can for each issue one at a time. At 9 years old, I would test the 12v battery and change if needed. Some auto parts stores offer help with testing batteries. The tire is also priority, I would take a note of which tire was low. If it's more than just an inflation issue, I would try to get it to a tire shop to identify the cause and permanently fix the issue. Then the light first is try to get get the codes with a code reader also troubleshoot the sensors and wires to the sensors for that location.

@Avesuccess 2 жыл бұрын

Thanks for professionally done video… 2010 Prius abs, check engine all similar light are on and it happened a few times were while driving at hwy speed all of sudden, yellow triangle of death comes on and display shows “check hybrid system” and there’s no more power,pulled over shut off car for a couple of minutes and it started with same light on cluster but this time car seems ok. Next day all lights goes off. Also brake pedal become softer when lights comes on. I did push brake 8 times within 5 seconds and light goes off but comes back on. Took to dealership, no codes. I was told also by local shop it could be brake actuator assembly and internal water pump. Don’t trust these guys. Please help as I’m running out of idea. Keep up the great video. 5stars

@TryAdaptLearn 2 жыл бұрын

Considering the two possible explanations, I would guess that the brake actuator assembly is likely the cause a of the braking system issues. The water pump is could be related to cooling system issues which would cause internal engine issues, coolant leaks or overheating. If you are unsure about the local shop you may want to take it back to the dealership and have them check something specific such as the brake actuator assembly. If there are no codes then this also may be an electrical issue such as batter and/or corrosion at the electrical connections (including grounds).

@AnyManProjects 7 ай бұрын

Paperclip trick didn't work for me. I replaced the entire suspension of my 2012 Prius... also ran it in gear while jacked up to check axles etc.. VSC light on ever since. Cleared memory using techstream, now ABS and Brake lights also on... can't seem to clear even after running solenoid valve calibration. DTCs say C1231 - C1345 - C1368. Brakes still work fine but no regen... help!

@TryAdaptLearn 7 ай бұрын

Please make the choices appropriate to your safety. If I was in a similar situation this is what I would do, I would start by disconnecting/re-connecting the battery. I would then erase codes. Next try to test drive in a safe enclosed area to see if the lights turn off and the codes stay off. Hopefully the test drive can check and calibrate the suspension/steering and brakes as the vehicle is on solid ground. If the vehicle functions properly but lights and codes are on, then I would tow or drive it to a Toyota service department to have a Toyota technician work on a wheel alignment (steering angle), check the ecu (possible cause of the codes/lights), and erase the codes and reset the lights. Once that is done, if the lights/codes come on, there is a possibility that there are are problems causing the codes and lights. There would also be the possibility that the sensors themselves are malfunctioning, the sensors detected problems when the vehicle was running on jack stands, the ecu is malfunctioning/ needs to be reset and/or or the connections/wiring to the systems is faulty/broken or not connected properly.

@christopherjohnson7337 Жыл бұрын

The diagnostic port faces straight down at the floor. Very difficult position to be able to view the two ports and jumper them correctly. (If you jumper the wrong port you can seriously damage the car I think). Any tips?

@TryAdaptLearn Жыл бұрын

Thank you for your question. I think that if it is hard to see, I would use a couple different options to help. One would likely be a mirror. If possible, the “selfie” camera and display of a phone would be good. Either way, it would good double check the orientation of the ports. It may also be helpful to have two diagrams of the ports. One would be looking at the port if you could see it directly and the second diagram as you see it with the help of the mirror or camera. Jumper wires are not the proper diagnostic tool and I agree that it is possible to do serious damage to electrical system if this is done incorrectly. There’s always the choice to take it to a Toyota certified technician. Good luck with trying to diagnose the issues which may be causing the lights to come on.

@kennyplay5982 Жыл бұрын

Question. Does the battery absolutely need to be replaced? Or can the jumper wire be used to remove the abs brake lights??

@TryAdaptLearn Жыл бұрын

No, The battery should not need to be replaced, it was only replaced in this vehicle because it was apart of issues that were specific to this vehicle. The battery can be tested on it's own to help troubleshoot issues. this method can reset the light but like many have mentioned, sometimes they will remain or come back on. The lights are indicators to the sensors and systems and may indicate that there is an ongoing issues that needs to be resolved before that can be reset and turned off.

@TAZ39XXX 2 жыл бұрын

Will this work for toyota yaris hybrid 2015?

@TryAdaptLearn 2 жыл бұрын

I'm sorry, I don't think so. This was a work around for the older models. I would double check the owners manual, a code reader and/or Toyota Service for these newer models since the electronics are increasing in complexity.

@TAZ39XXX 2 жыл бұрын

@@TryAdaptLearn , many thanks

@TAZ39XXX 2 жыл бұрын

@@TryAdaptLearn, also there's hardly any information for the yaris hybrid online, everything seems to be for the prius ☹

@TryAdaptLearn 2 жыл бұрын

They might have similar systems but I can understand that you want something specific to your vehicle. Hope your search goes well.

@user-br7bf5wz2m 3 жыл бұрын

good

@TryAdaptLearn 3 жыл бұрын

Thank you.

@mikegiambrone3007 3 жыл бұрын

I"m having an issue with my abs lights on my 2012 prius. when I use your jumper method it works to reset the lights but, as soon as I start driving they come on again. How can I figure out the root problem with out going to the dealer ? I know they will hit me over the head - Thanks

@TryAdaptLearn 3 жыл бұрын

One way to trouble shoot is to use a code scanner that has ABS capabilities. Some auto parts stores will also use their ABS scanners to help you diagnose free of charge. Although it will take more time some service departments at dealerships will diagnose for free, you just have to to ask specifically how much they charge for diagnostic only. I have listed the items to look out for in the pinned comment. The lights could come on due to any of those items. Unfortunately with these vehicles, the most common cause is the the ABS pump and/or actuator. The part alone is expensive, no matter who does the labor, I would recommend a genuine Toyota part.

@redbudinninc5919 3 жыл бұрын

kzfaq.info/get/bejne/iatdd6V739aafaM.html i used an ABS code reader this way. Why no mention of the brake failure alarm buzzer?

@timscorner8137 3 жыл бұрын

The VSC, ABSv ane Brake lights came on after changing the front brake pads yesterday. I've checked and no codes came on, the battery is brand new and the fuses are in good shape.

@TryAdaptLearn 3 жыл бұрын

Sometime these warning lights appear due to a faulty part in the abs system, sometime the sensors sending a signal to turn the lights on. If they still remain on after trying to reset the lights, you need a diagnostic tool specific to analyze ABS/brake systems and/or you consider taking it to Toyota service department to diagnose what is causing the lights to stay on.

@1979jerrod 3 жыл бұрын

I also didn't realize you're supposed to disconnect the battery.

@petec3857 3 жыл бұрын

It’s a recall i called Toyota

@sherifmohsen1974 Жыл бұрын

In addition to the red brake warning light I have yellow brake warning light, ABS, VSC and traction lights on. There is no engine light but also whenever applying brakes the red triangle 🔺 and door open lights go on as well and the MFD keeps switching back and forth between navigation and P lock shift warning screen and beeping. Also the speedo and odometer - white they still illuminate - do not work. Speedo shows zero all the time and odometer is stuck at a specific mileage count.

@TryAdaptLearn Жыл бұрын

It seems like there are issues with not only resetting the lights in your vehicle but also the systems that they are meant to warn you about. If you have a code reader, it may be worth it to read the codes that may be associated with the warning lights. Since the red triangle appears when you apply the brakes, I would recommend taking the vehicle to a certified Toyota certified specialist with the proper tools to diagnose the multiple issues associated with the warning lights in your vehicle.

@andrewcox7179 3 жыл бұрын

I put a jumper wire and pressed start but no diagnostic screen. Any suggestions??

@TryAdaptLearn 3 жыл бұрын

You can double check the pin numbers that the jumper is in but if there's no diatonic screen showing in the display, you'll likely have to take it to a Toyota technician with the proper tools to troubleshoot the issue.

@shakhawannader3944 3 жыл бұрын

I have the same car and while I’m driving the light ABS and brake light just come on and The system of the break was hard as well and I had a problem when I was turning the steering right way or the left away was beeping then I stopped the vehicle I turned off for five minutes and turned back on everything is gone is that normal

@TryAdaptLearn 3 жыл бұрын

It's good that you were able to resolve your issue with a restart.

@shakhawannader3944 3 жыл бұрын

But I haven’t done Anything by herself restart

@TryAdaptLearn 3 жыл бұрын

You wrote you stopped the vehicle and turned it off so that could have initiated a restart or recheck. If any lights come back on or you feel that the vehicle is not braking normally, you should take it to a Toyota technician to have them run diagnostics on the braking and electrical system.

@shakhawannader3944 3 жыл бұрын

@@TryAdaptLearn Well it happened last night I am going to drive today again but I have done something I released the pressure of the front tires I don’t know that cause the problems

@shakhawannader3944 3 жыл бұрын

@@TryAdaptLearn Thank you so much yeah I drove my vehicle and nothing come back I think everything is okay now what do you think do I still need to check it on shall I just ignore it

@hammadhamid5583 2 жыл бұрын

Hi i was driving 2008 prius on motorway light come up abs vsc and handbrake light but strange thing my odometer stop working its stay on zero every time i drive car map used to go with car before now its stay where i park (look like car shows brakes on and car not moving) i did reset thing as from ur vedeo not understand y can u help me with this

@TryAdaptLearn 2 жыл бұрын

The procedure in this video would reset the lights if the systems are functioning properly. Since you have multiple issues including braking system lights, odometer and map, I would recommend taking it to a certified Toyota service location to help you troubleshoot the issues associated with your car. As a humble opinion, a malfunction in the braking system alone is enough to create a safety issue and it sounds as if you are dealing with multiple issues that require someone to inspect your car in person.

@shannonsprowls-wallace6519 2 жыл бұрын

I had the same problem on my 2009 and after cleaning the speed sensors on both from tires it worked again.

@naseemawan457 4 ай бұрын

I am from Pakistan

@alennovak8446 10 ай бұрын

For what is that KEY switch next to the tyre pressure set button?

@TryAdaptLearn 10 ай бұрын

Good question. The switch labeled "Key" at the bottom of the steering column is used to enable or disable the smart entry and start system. When the switch is in, it is disabled, when the swtich is out, it is enabled. The "Key" switch is unrelated to the issue in this video which is why is was not identified in the video.

@alennovak8446 10 ай бұрын

@@TryAdaptLearn thank you. :)

@canuck2025 Жыл бұрын

I have a 2014 Prius c. Will this work here?

@TryAdaptLearn Жыл бұрын

I don’t think so. This was a quick hack with a jumper wire. I think the newer models will require a proper diagnostic tool.

@canuck2025 Жыл бұрын

@@TryAdaptLearn Ok. Thank you

@JonEhBee 10 ай бұрын

Are you sure it's the 5th pin hole on the top ( the top being the fatter side of the obd) and not the 4th? I read on prius chat that it's the 4th pin and 13th pin, which are both 4th from their respective sides.

@TryAdaptLearn 10 ай бұрын

It could have worked for others in a different configurations. In this video, on this vehicle, the wire was inserted in the 5th pin from the right on the top as mentioned in the video. That being written, the process in this video should not be considered a substitute for a certified Toyota technician with the proper Toyota diagnostic tool.

@JonEhBee 10 ай бұрын

@TryAdaptLearn My bad. You actually did say 5th from the right on top, which is 4th from the left (#4). This didn't fix my problem because I found the seat rail mangled through the loom and through about 4 of the 9 or 10 wires that go to the wiring harnesses under my driver seat!

@jtylergibbs5884 2 жыл бұрын

I have an 08 Prius I am having issues getting it started and pressing on breaks does not turn brake lights on when applying pressure any ideas

@TryAdaptLearn 2 жыл бұрын

Sounds like two separate issues occurring at the same time. Starting issues could be low voltage in the battery, fuel system issues or ignition system issues. The brake lights are a separate system and usually cause by light bulbs or the switch that turns on the light bulbs when your foot is on the brake pedal.

@jtylergibbs5884 2 жыл бұрын

@@TryAdaptLearn I have tested the battery, brake light switch, checked all fuses, and bulbs for brakes are not blown. I’m curious on my next steps

@jtylergibbs5884 2 жыл бұрын

I have not tested the block like fuses idk if any of them would contribute to the situation?

@savemyneighborhood 6 ай бұрын

Hi I wonder if anyone else have this similar problem. After I replaced odometer display module, Vss, maintenance light come on and won’t got away. This Toyota 2007 Prius. Everything was working before except brake light stay on. I though buy one multi combination display module will fix it but make it more worst. I put back the original part and not I have more problem. The car is driving normal.

@TryAdaptLearn 5 ай бұрын

I don’t know if anyone has specifically the same issues, but with so many issues, it may be worth considering to take the vehicle to a certified Toyota technician with the proper tools to diagnose the systems.

@user-ir8ho1ys6w 7 ай бұрын

Can you tell me which fuses I need to remove? I don’t understand English, just write here

@TryAdaptLearn 7 ай бұрын

You can remove the fuses that you want to check to see if they are working.

@JuhaAnttila 3 жыл бұрын

Followed the steps. Got the ok signs, BUT IT DID NOT DO the trick. So I continuea

@TryAdaptLearn 3 жыл бұрын

If this process did not reset your lights, it is possible that you vehicle sensor/s may be bad. If they are functional, they may be indicating that you have a problem that need a to be fixed before the lights can be reset. While troubleshooting the issue it may be worth considering to take the vehicle in to have a Toyota technician with the proper tools to look diagnose the issue further.

@oyebanjiseun4721 Жыл бұрын

Why is my car abs and vsc blinking whenever i start my car and my gear will change to drive4 instead of D

@TryAdaptLearn Жыл бұрын

I am sorry but I do not know what exactly is happening with your car. Usually, if the ABS and VSC blink when you start the car, it is a system start up and/or a system check. As far as your gear changing to drive4 instead of D, that sounds like a transmission issue and is a separate problem and issue than the abs and vsc lights. Here are more of my opinions related to the abs and vsc lights: ABS is Anti-lock braking system, VSC is vehicle stability control, both are related to the braking system. If the abs and vsc remain on when the car (and engine) is started, it indicates that the sensors are warning you about maintenance needed or malfunctions in those systems. This video was a demonstration of how the lights were reset with the vehicle in this video when there was no maintenance needed or a malfunction in those systems.

@meassavuth4649 2 жыл бұрын

I do not understand why many peoples just click to reset any error coming up ? So if your ABS motor broken then we just clear error for what. ? so will it coming again ??? Or some sensor bad or broken so can we just clear the error or need to change the motor first and than clear the error ???? Please answer my question because there are different ideas of each person ,,,

@TryAdaptLearn 2 жыл бұрын

Resetting warning lights will not fix the electrical or mechanical issues that they are meant to bring to the driver’s attention. There are however situations in which someone would want to reset the lights. These include: Troubleshooting electrical issues that may be causing the lights to stay on. If the lights remain on after a new part is installed. In the case of this video, the 12v battery was a part of the issue. In other cars, a low voltage battery will likely not create this issue but this car has the 12v and a hybrid electrical system. The more complex a (electrical) system is the more likely it may need resetting, troubleshooting, and/or maintenance.

@mickelagodop5732 3 жыл бұрын

would it work for a toyota harrier 2005 model?

@TryAdaptLearn 3 жыл бұрын

I’m not sure but would say no. I think this is specific to the Prius in this video. Also keep in mind that it is a work around. The proper procedure would be done by a Toyota technician with diagnostic tools.

@gabrielavina5932 2 жыл бұрын

I put air on my tires and after I turned on my 07 Prius I got the red triangle and ( ! ) I'm worried 😓 the screen display Problem and the red car.

@TryAdaptLearn 2 жыл бұрын

If you recently added air to your tires and a light (a tire and exclamation in the middle) is on, you may want to: double check the air pressure with the manufacturer values (in the manual and/or sticker on the door), then reset the tpms system using the tpms reset button. The other lights are indicating other issues. A car with a key could be the alarm system. A car with an exclamation in the middle could be the hybrid system warning. An option to consider is that if you are unable to troubleshoot what the lights are indicating or how to resolve the issues (before trying to reset the lights), you may want to call a Toyota service department and ask them for an estimate for their help to identify the issues that are causing the lights to appear.

@BrianLarosa-um5qw Жыл бұрын

Clean your hybrid fan an make sure it's working

@thomasmclean4020 2 жыл бұрын

Not working for me can't get to the screen

@TryAdaptLearn 2 жыл бұрын

I'm sorry to here that this procedure didn't work for you. If I were in your position I'd disconnect the negative battery cable and troubleshoot possible reasons why the light is coming on. If that doesn't work you may need to take it in to a Toyota service technician.

@endracism3971 3 жыл бұрын

I put the wire to 4 and 9 on obd and now my car will not start

@TryAdaptLearn 3 жыл бұрын

I recommend you have a professional technician look into the issues with your car. I don’t know where 4 and 9 is on your one port but if the car will not start, I would disconnect the wire and I would not try it again. If it was my car, I would disconnect the negative cable from the 12v battery, then I would check all fuses. Before I reconnect the cable, I would check the voltage on the 12v battery. If that doesn’t work I would call a professional to diagnose the issue.

@onthegowithjoetv 2 жыл бұрын

mine keeps coming up everyday

@TryAdaptLearn 2 жыл бұрын

If the lights display everyday it may be an indication that there is an issue with the parts or systems that need to be checked by an automotive technician.