Robert Dana teaches you how to install a oil pan properly so it will not leak.

Рет қаралды 196,183

8 жыл бұрын

Robert Dana teaches you how to install a oil pan properly so it will not leak. The model he is working on is a 400 small block chevy but the techniques he is using hold true on most models.
Parts:
Small Block Chevy Overhaul Gasket Set, 400 Chevy '70-'81
amzn.to/3qGqUif
Permatex 82180 Ultra Black Maximum Oil Resistance RTV Silicone Gasket Maker, 3.35 oz. Tube
amzn.to/3y6iZxo
Tools:
Milwaukee Electric Tools MLW48-22-9214 Pry bar Set
amzn.to/3AhLB8J
TEKTON 3/8 Inch Drive x 12 Inch Flex Head Quick-Release Bent Handle Ratchet | SRH33112
amzn.to/3hc9Y0g
TEKTON 3/8 Inch Drive Extension Set, 3-Piece (3, 6, 10 in.) | SHA91005
amzn.to/3hoc0ZX
GEARWRENCH 11 Pc. 3/8" Drive 6 Pt. Mid-Length Socket Set, SAE - 80555S
amzn.to/3jFKIkF
GEARWRENCH 14 Pc. 3/8" Drive 6 Point Mid-Length Socket Set, Metric - 80554S
amzn.to/3qKoyPt
Things used to make this video
1. Adobe Premier Editing Software amzn.to/2DOgo1b
2. Adobe After Effects amzn.to/2YaezUd
3. Abobe Photoshop amzn.to/2Ll6dYl
4. Westcott Flex Daylight Set amzn.to/2H1HOBs
5. Sanken COS-11D Lavalier Mic amzn.to/2VeAzjS
6. DJI Mavic Pro Fly More Combo amzn.to/2Low8hC
7. Epic GoPro / Action Camera Mount for your Boat amzn.to/2VevCaG
8. Dracast Pro On-Camera Light amzn.to/2PTwcVp
9. Dracast Halo Ring Led Light amzn.to/2H7yvkZ
10. Nikon D5600 24.2 MP DSLR Camera amzn.to/2LpD91M
11. Sony PXW-FS7 XDCAM Super 35 Camera System amzn.to/2DWufml
12. Quick Release Shoulder Plate amzn.to/2JqFeYS
#DIY #chevrolet #howto

Пікірлер: 119

@aaron71 7 жыл бұрын

Thanks for the vid. It's a simple thing, but never hurts to see someone else do it just to be sure!

@howtodoityourself6178 6 жыл бұрын

I hear you

@hankschrader149 3 жыл бұрын

My thoughts exactly

@JohnWhite-zt5gb 4 жыл бұрын

Thank you for the tips, lotta foresight a newby would never have thought of!

@ramoncasillas4490 4 жыл бұрын

Great tutorial video. Thank you. Much appreciated

@RESTORATIONRESCUE 2 жыл бұрын

Great video, We are just getting to this point in our engine build and this is really educational and really helped.

@jeremylaxton8639 4 жыл бұрын

Great video. Thanks for the tips

@christophernelson259 Жыл бұрын

thank you so much for the help and views are great!!! I was afraid that the little black strip that goes where the timing chain is a extra rubber thank god for your video's is a blessing now I can finish my 1987 Chevy el Camino. stay safe god bless.

@juneenriquez9720 Жыл бұрын

Great detailed video, I am at this part right now on my 472, need to turn the engine on the stand but it’s heavy.

@gilbertpinks7829 10 ай бұрын

Nice job. Thanks again.

@michaelpacheco6332 5 жыл бұрын

On an el Camino do I have to pull the motor a little bit to remove the oil pan .....

@hankschrader149 3 жыл бұрын

Great video Robert thank you

@DavidJonesOpalImages 3 жыл бұрын

Glad you enjoyed it

@x-man4702 5 жыл бұрын

Can the RTV be applied to the block and the oil pan or just one or the other?

@jeffmallory2722 5 жыл бұрын

If using cork tack enough to hold gasket and join end seals in place

@stephenfaulkner1448 2 жыл бұрын

If your gonna use RTV on all of it also. Its wise to put a thin coat on. Put the gasket on and press it down to squish the RTV flat. Then clean off any that pushed out to the inside of you pan before bolting it down. Any loose RTV reeks havoc on filtering and flow systems. That said. Other than where gaskets meet. Gaskets are designed to not need RTV.

@mrj24811 20 күн бұрын

It literally tells you to use rtv in the manual with cork gaskets. Unless you use a rubber gasket, but even then if it's a 2 piece, you want to put a lil where that meets.

@ccfreedomseekerconstitutio8767 3 жыл бұрын

Appreciate your help

@vegasuperstar6 5 жыл бұрын

robert!! you might have a second career as a cake decorator!!!!! hahaha!!!

@tonycugudda250 7 жыл бұрын

Awesome video...

@howtodoityourself6178 6 жыл бұрын

Thank You

@kracksmith4ejm1 3 жыл бұрын

so for all oil pan that use gasket should have liquid gasket under and on top of that gasket for a no leak install?

@godsoutlawneto 4 жыл бұрын

Thanks for this video. It will help me alot on my project. Thanks🤙🏼

@jayman2261 3 жыл бұрын

I'm installing an oil pan gasket on a 1954 Cadillac 331 engine going from under the car, with the engine in the car...Should I cement the front, and rear seal on the pan side, or the block side, to prevent it from getting dislodged when I put the oil pan back up??? I use weather strip adhesive, it seem to hold the best... ????????????????????

@LeFraudHasChokedInSIXFinals 2 жыл бұрын

The biggest thing I learned from this video was how to use a floppy-handle rachet.

@55chevyman4u2nv 5 жыл бұрын

helpful thank you

@matthomas5645 4 жыл бұрын

Great video! I’ve taken my Jeep to a mechanic 3x to get the leaks stopped. $1300 later and it’s still leaking. I’m going to follow your instructions........stay tuned for a follow up!

@dantzlerfarm7570 2 жыл бұрын

did you get it fixed?

@matthomas5645 2 жыл бұрын

@@dantzlerfarm7570 yes sir. Thanks for the follow up. I did get it fixed.

@MartinLopez-ys5dm 4 жыл бұрын

David, on a 440 with a baffle between the block and the oil pan...Where does one put the gasket? TIA.

@Paulholio69 5 жыл бұрын

Is it the same with a paper gasket?

@oscarcontreras3714 4 жыл бұрын

Very good. Now I andersten why I got lek...Muchas gracias.

@jeffmallory2722 5 жыл бұрын

Using screw in studs with slots in end helps align gaskets.

@kennyc388 4 жыл бұрын

Absolutely.....makes it much easier than diddling around with gasket for alignment

@jeffmallory2722 5 жыл бұрын

Need steady hands when installing in truck. Cant clean and prep surfaces enough. Clean surfaces is a must.

@gregageo 4 жыл бұрын

Good Info, TY

@user-cg9ly4wg2s 3 ай бұрын

I just use a one piece rubber gasket. Never any leaks! Easy removal too!

@manwar999 4 жыл бұрын

same for trans pan gasket?

@55chevyman4u2nv 2 жыл бұрын

does 350 dipstick is on the driver side ? not sure if I have 350 are a 400 thanks

@MrEyad1990 3 жыл бұрын

this guy loves RTV.

@danielthompson2692 3 жыл бұрын

What size are the bolts and nuts 4 corners

@jeffmallory2722 5 жыл бұрын

Used 1 pc blue on 88 chevy truck 350 3 weeks ago dry. 3 tiny blobs in corner on block sides. No leaks

@tvlu4365 4 жыл бұрын

So is a blue once piece batter then cork? I'm at this point to install just not sure what is better since I see both

@richgar3713 4 жыл бұрын

I can find the gasket for 70cutlass can you help me with

@garytaylor797 3 жыл бұрын

its a lot easier when the engine is out and in a stand like that rather than the way i have to do it In The Car

@normhodgkinson6965 3 жыл бұрын

All small block Chev had dipstick on drivers side prior to 1986.

@hueroski 5 жыл бұрын

I bet this man puts RTV between his tires and wheels too!

@prestoconner4004 4 жыл бұрын

love to see a video that shows how to do this in the truck or car. lol

@ccfreedomseekerconstitutio8767 3 жыл бұрын

I am doing a 71 307 chevy engine seems to look the same as far as gaskets

@johnjoole2258 6 жыл бұрын

Thank-you

@howtodoityourself6178 6 жыл бұрын

Thank you for watching and good luck with your project

@jamesslate8929 6 жыл бұрын

Rob How Can I Get Ahold Of u when I need advice I watch all your videos and would love to Here some of your knowledge I’m a rookie engine builder and I always need help

@tvlu4365 4 жыл бұрын

What do you recommend a cork gasket or a once piece rubber gasket?

@scottfirman 3 жыл бұрын

Too many guys over tighten the cork gasket and ruin it. If I have a choice, I go with rubber every time. Most new vehicles use rubber or nothing but silicone now anyways.

@dougmasterson6518 5 жыл бұрын

Great job teach...🏆🏆🏆

@howtodoityourself6178 5 жыл бұрын

Thanks!

@hockeyman2274 2 жыл бұрын

Really easy to do when the engine is upside down on a stand and dry. Show us how to do this after someone has f'ed up and it's in the car and oil in it.

@tmguy1068 Жыл бұрын

Sure wish there was a how to with tip for doing this with the engine still in the truck. Have a 4x4 with a 351M that is fighting me every step. They don't make a one piece for the 351M or 400 that I have found.

@haynesenterprises_inc9202 Жыл бұрын

Probably won't leak, but too much rtv makes it very difficult to remove the pan without destroying it. Wouldntvit be better to just seal the pan side and then the end corners on the engine side?

@ScottDLR 5 жыл бұрын

I suggest people use a modern 1 piece rubber gasket. No joints to leak and no sealant needed.

@maxierex6036 Жыл бұрын

How much tourque on the bolt's

@landissmith6920 7 жыл бұрын

it should be easy when your working on moter thats upside down and out of the truck but try to do it whith it in the truck not as easy

@howtodoityourself6178 6 жыл бұрын

Oh yeah! but it still can be done..but not on camera

@zoltanzoldi6550 6 жыл бұрын

Just roll your truck upside down, it will make this job super easy without taking the engine out.

@kingromo846 4 жыл бұрын

landis smith same thing I was just about to say lol I just did it on my brothers 283 engine impala it was a bitch to do..

@kennyc388 4 жыл бұрын

you're working on motor......... You're welcome !

@joeguerrier7975 3 жыл бұрын

@@zoltanzoldi6550 I know someone who did that with a jeep...lol

@nearpar 5 жыл бұрын

FROM FEL PRO: In the case of most Fel-Pro® oil pan gaskets, they are to be installed dry. When installing PermaDryPlus® and PermaDry® gaskets, they must be installed clean and dry. RTV is only necessary at the “corners” or where there may be a stepped area such as an RMB retainer to block joint. Keep the following in mind: Adhesives should only be used on “paper type” or cork/rubber type gaskets. No adhesive will stick to silicone. Molded silicone gaskets must be installed dry. Adhesives or RTV used in excess can potentially get into the crankcase and oil galleys and cause engine damage.

@renter6971 5 жыл бұрын

How can you do this job with the motor in the car? If there is paper and rubber 4 part gasket (429 Cadillac).

@jamesfarmer2748 5 жыл бұрын

yall listen to this guy with the rtv. permadry is the way to go!

@expressyourselfist 4 жыл бұрын

Great job! I see that you applied the sealer to the engine block, then placed the cork gasket on top of it, then you applied the sealer again to the top of the gasket. I was thinking to do exactly that. it makes perfect sense. The only thing that bothers me is since this way you have four surfaces glued together: engine/gasket/gasket/oil pan. If you did not use the gasket ,applied sealer only between pan and the engine, you would have had only two surfaces glued together. I do not know what to do now, gasket or no gasket, new cars seem not to have any gasket, manufacturers even use glue, there so many youtube videos on this subject I am all confused. Sometimes having less choice is better, like in the old days just cork gasket and grease that is it. Anyway I will do what you did, as I said it made perfect logical sense.

@dons1932 2 жыл бұрын

FYI you only typically want to do no gasket just sealer, only when you can guarantee a perfect machined surface. Most new cars that only run sealant have alloy blocks and / or sumps, so they are machined well, better than the pressed tin stuff.

@howardblasingame7961 Жыл бұрын

@@dons1932 Good point.

@mommmmmmuy 11 ай бұрын

I need help on the cork gasket

@briannielsen7176 Жыл бұрын

Why don't you use a rubber oil pan gasket? If you have a rubber gasket do you need all that rtv?

@markstamper9081 3 жыл бұрын

Anyone refer to torque specs anymore?

@splitsecond6911 5 жыл бұрын

Manufacturers and mechanics say not to use RTV on cork gaskets it will cause them to split.

@kennyc388 4 жыл бұрын

Yes, why is he using both ???

@cesargranados8295 2 жыл бұрын

Info on oil pan???????????????

@robertcowan8211 4 жыл бұрын

I ALWAYS USE 3M WEATHER STRIP ADHESIVE ON BLOCK THEN ULTRA BLACK ON PAN SIDE OF GASKET. LET IT SETUP FOR 24 HRS B4 ENGINE STARTUP

@howardblasingame7961 Жыл бұрын

Fascinating. The first I've heard of 3M weatherstrip

@jabierlopez8289 7 жыл бұрын

did he torque it ?

@tonycugudda250 7 жыл бұрын

Old school baby!

@pistolpete007 Жыл бұрын

Robert I'm doing the same work on the same engine. Question, I'm trying to replace the gasket on the oil pump. I took the 4 bolts out but the bottom plate won't budge. What am I missing?

@tjjtjj5720 7 жыл бұрын

isn't using rtv and a gasket essentially making double gasket and being prone to leaks

@howtodoityourself6178 6 жыл бұрын

Years of doing it this way has worked for me

@re9947 6 жыл бұрын

TJJ TJJ That plus it makes the gasket slip out

@ianwilds3139 4 жыл бұрын

Use sealant on four corners where front and rear arches meet the flats..only between block and gasket..not between gasket and pan.

@azwb 3 жыл бұрын

I thought it was standard to put the gasket sealer on the pan only to keep it in place?!? If/When you have to replace the gasket you would only need to clean the pan and not the block.

@scottfirman 3 жыл бұрын

NEVER ,NEVER , use RTV with cork. You can use whats called gasket tack to get the gasket from moving around before putting the pan back up under the vehicle. Its a contact adhesive designed for placing cork gaskets. RTV is only used where recommended by manufacturer, never will you see it used with cork and never should it be used with cork. It makes it slippery and doesn't seal as intended.The only place RTV is used in most applications is at the timing cover or crank seal joint between a rubber seal and the cork. Thats it.

@jeffmallory2722 5 жыл бұрын

4 tiny blobs in coners. Minimal amounts. No excess. Hard to do in truck

@billvogel359 Жыл бұрын

Won’t synthetic oil work it’s way through cork gaskets?

@Enviros 4 ай бұрын

Cork is impermeable.

@billvogel359 4 ай бұрын

@@Enviros says you, I’m hearing different. Ask uncle tony

@scottbezotte5414 4 жыл бұрын

You put the timing cover on with no timing indictor. Next video for pan it's there. Is it self installing?

@Eeropolvasti Жыл бұрын

Good job, can you give me torque for those oil pan bolts, thanks!! Or, you need no torque??? Just "nic and tight";o)

@Malvarez909 3 жыл бұрын

i did this and it leaked. I was told to never use RTV on the gasket. This debate has been going on for years.

@caleb4750 3 жыл бұрын

No silicone like he uses on cork... never they do not mate well

@Myvintageiron7512 6 жыл бұрын

RTV should NEVER be used on the oil pan gasket it can clog up the oil pump GM and Ford both say not to do this

@jimdavidson5208 6 жыл бұрын

Are you kidding? RTV is used on EVERY repair in America. Slather that mess all over the place.

@micmic9410 5 жыл бұрын

They purely use it on Toyota oil pans, but I think gm and ford say this because DIY’rs put way too much. And I guarantee many people that do not read instructions. Just another 2 cents.

@automedic9781 5 жыл бұрын

It depends on the vehicle and type of oil pan. Some use a regular gasket. Others use RTV or other silicone based sealants depending on the manufacturers recommendations. Just because one Ford/GM vehicle says not to use it on that one doesn’t mean that a different one won’t have other instructions

@automedic9781 5 жыл бұрын

I would personally never use both, but on a vehicle where it’s required, Absolutely

@joddball 5 жыл бұрын

i have this issue i found out when lost oil pressure and removed oil filter to find rabber sealent rapped around the oil filter , now have to remove the sump on my 400 cleveland big block

@vicniebrzydowski7793 10 ай бұрын

Buy a torque wrench please.

@arfreak1979 4 жыл бұрын

Fuckin Bubbles is turning wrenches for Chevy? Huh...good to know

@zakpeterson6713 4 жыл бұрын

It leaked

@psiewert83 4 жыл бұрын

First mistake he made is using the cork gasket

@tthams73 Жыл бұрын

Well that sure as hell isn’t how you install an oil pan! Throw the RTV in the trash! It does not belong any wear in, on or around an engine! For cork gasket use a little Vaseline. For paper or rubber gasket follow the manufacturers directions. Which is 100% of the time: “DO NOT USE RTV OR ANY OTHER GASKET SEALER.”

@mysterycomment1553 2 жыл бұрын

You should never do this lol

@7DeuceCutty212 3 жыл бұрын

Uh cork. Why!!!!!!!!!!!😫

@joshcx7 3 жыл бұрын

A lot of know it all is whining about how he’s doing it😂😂😂😂. He’s an engine builder, do you think he’ll like customers coming back just to fix a stupid oil leak. I did it his way in my Infiniti G35 and G37, when I installed an oil pan spacer, no leaks years later.