I was amazed by Dyson - see how this works Watch the video to learn more to support my site use the links below Aliexpress: s.click.aliexpress.com/e/_DmB... Amazon : amzn.to/3owFhJF Ebay: ebay.us/lPoJJu
Пікірлер: 19
@didiervibert61117 ай бұрын
Hello , Do you know how the speed selector works on the small electronic card ? . What technology is used ?
@dyson2hand11 Жыл бұрын
v11 motor hears 1 noise when operating, is there any way to fix them
@bwoah768 ай бұрын
hey mate, i really need your help, if your dyson v10 is still opened up, can you check how many volts it pulls and at what frequency? i have a motor from a damaged v10, i would really appreciate it if you can tell these values, thanks a lot in advance
@jeniyadaktiarov Жыл бұрын
אני גם פירקתי , הציר עשוי מקרמיקה והגוף עושי מפלסטיק קשיח שעמיד לחום גבוהה ושביר מאוד
@RoeeBloch Жыл бұрын
good
@vaifrax Жыл бұрын
How did you remove the PCB and the motor (center of image) from the housing (top left of image), is the PCB glued in?
@malcomsue Жыл бұрын
The PCB is glued to the housing, however, it is really the solder on the contacts that hold it on.
@vaifrax Жыл бұрын
@@malcomsue thanks, I see it now, the two large solder blobs in the center (also on my V11). Seems my 30W soldering iron is underpowered, though, I can't melt it 😞
@vlady32982 ай бұрын
What hall sensor is? Numer on it? Thanks
@gigiaalfa2 жыл бұрын
Hi, I have the same problem, the filter light keeps blinking even with everything clean, but the motor doesn't spin. Have you figured out what's the issue?
@francescoceccotm8 ай бұрын
Non ha capito niente!
@bagibadoo4392 ай бұрын
I glued a neodymium magnet to the board in the right spot (corner) and it works.
@NicosLeben9 ай бұрын
My Dyson v11 keeps pulsing in normal and low power mode, but runs fine in boost mode. That phenomenon started happening from one day to the other. Do you know what could be the reason for that? Do you think there is anything I could do about it? Maybe just cleaning it up somehow? I already disassembled it to the core and now I guess I have to desolder the motor from the PCB to dig even further. Do you think there is something I can do before that to fix the issue?
@Peppasteppah8 ай бұрын
Clean out the vacuum, not unscrew it, just wash the filter and brush the metallic grill under the dust container
@NicosLeben8 ай бұрын
@@Peppasteppah I had to buy a new core. Of course I cleaned it completely before digging deeper. But it seems the electronics or the motor were defect.
@kebox1846 ай бұрын
My dyson v11 also pulsing in slow n normal mode but ok in high mode.. tried cleaning it but still pulsing.. I changed the motor and it worked fine in all mode.. probably the circuit board got some faulty components..
@igorsurkov34052 ай бұрын
добрый день. могли бы назвать маркировку микросхемы U12 .как она в миру зовётся?
@Venerand0Tero-fn6ki8 ай бұрын
How buy motor in dyson v15
@qq-dw3si2 ай бұрын
nothing to be shocked. single phase BLDCs are widely used for many application.