HOW TO FIX SOFT FOOT ON SHAFT ALIGNMENT | ENGLISH | Rotating and Static Equipments

Рет қаралды 17,489

3 жыл бұрын

IN THIS VIDEO SESSION, YOU WILL LEARN ABOUT THE SOFT FOOT ON SHAFT ALIGNMENT. IT IS ONE OF THE PRE-ALIGNMENT PROCEDURE FOR ANY TYPE OF SHAFT ALIGNMENTS.
TOPICS EXPLAINED:
DEFINITION OF SOFT FOOT, EFFECT OF SOFT FOOT, CAUSES OF SOFT FOOT, TYPES OF SOFT FOOT, PARALLEL SOFT FOOT, ANGULAR SOFT FOOT, SPRING OR SQUISHY SOFT FOOT, STRESS INDUCED SOFT FOOT, SOFT FOOT MEASURING METHODS, PREPARATION FOR CHECK SOFT FOOT AND FIXING SOFT FOOT BY FEELER GAUGE AND DIAL INDICATOR.
For Rotating and Static Equipments Trainings online and offline sesstions
Please call or Whatsapp +918680032253
rotatingandstaticequipments@gmail.com
RASE Technical Training Centre
Join this channel to get access to perks:
/ @rasetech
REQUIRED TOOLS:
STEEL RULER, FEELER GAUGE, MAGNETIC STAND WITH DIAL INDICATORS, PRE-CUT SHIMS, SPANNERS, AND TORQUE WRENCHES.
SUBSCRIBE FOR MORE ROTATING AND STATIC EQUIPMENT VIDEOS.
/ @rasetech
RIM AND FACE ALIGNMENT FORMULA METHOD | ENGLISH
• RIM AND FACE ALIGNMENT...
HOW TO FIX SHAFT ALIGNMENT SOFT FOOT | TAMIL
• HOW TO FIX SHAFT ALIGN...
RIM AND DOUBLE FACE DIAL ALIGNMENT FORMULA METHOD
• RIM AND DOUBLE FACE DI...
RIM AND FACE DIAL ALIGNMENT TOOLKIT FOR META FLEX COUPLING
• RIM AND FACE DIAL ALIG...
BASIC OF ANTIFRICTION BEARING AND FINDING OF BEARING TYPES BY BEARING NUMBERS | English
• BASIC OF ANTIFRICTION ...
CENTRIFUGAL COMPRESSOR DRY GAS SEAL SUPPLY SYSTEM | ENGLISH
• CENTRIFUGAL COMPRESSOR...
MECHANICAL SEAL ASSEMBLING PROCEDURE | CENTRIFUGAL PUMP | ENGLISH
• MECHANICAL SEAL ASSEMB...
STUFFING BOX SQUARENESS | BORE CONCENTRICITY | ENGLISH
• STUFFING BOX SQUARENES...
STUFFING BOX ASSEMBLY | CENTRIFUGAL PUMP | ENGLISH
• STUFFING BOX ASSEMBLY ...
CENTRIFUGAL PUMP OVERHAULING PROCEDURE | DISMANTLING AND ASSEMBLING | ENGLISH
• CENTRIFUGAL PUMP OVERH...
BAR SAG | ALIGNMENT
• BAR SAG | ROD SAG | S...
REVERSE DIAL INDICATING FORMULA METHOD ALIGNMENT
• REVERSE DIAL INDICATIN...
REVERSE DIAL INDICATING ALIGNMENT|OPPOSITE DIAL POSITION|FORMULA METHOD VS GRAPHICAL METHOD
• REVERSE DIAL INDICATIN...
REVERSE DIAL INDICATING ALIGNMENT|CROSS DIAL POSITION|FORMULA METHOD VS GRAPHICAL METHOD
• REVERSE DIAL INDICATIN...
BELT DRIVE PULLEY ALIGNMENT STRAIGHT EDGE METHOD
• BELT DRIVE PULLEY ALIG... RECIPROCATING COMPRESSOR PISTON OVERHAULING PROCEDURE
• RECIPROCATING COMPRESS... CENTRIFUGAL MULTISTAGE PUMP ROTOR IMPELLER ARRANGEMENT
• CENTRIFUGAL MULTISTAGE...
HEATLESS DESICCANT AIR DRYER AND OPERATING TIME SEQUENCES
• HEATLESS DESICCANT AIR... HOW TO SELECT SPANNER SIZE FOR BOLTS AND NUTS | INCHES TO MM | MM TO INCHES
• HOW TO SELECT SPANNER ...
DUPLEX BEARING ARRANGEMENT IN SINGLE ROW ANGULAR CONTACT BALL BEARING
• DUPLEX BEARING ARRANGE...
#softfoot
#shaftalignment
#rotatingandstaticequipments

Пікірлер: 76

@rasetech 3 жыл бұрын

Dear Friends, If you want this power point presentation of Soft foot, kindly comment your email address in this video comment box.

@MuhammadAli-ev2ym 3 жыл бұрын

alichaudhry333@yahoo.com

@rasetech 3 жыл бұрын

Kindly check your mail

@MuhammadAli-ev2ym 3 жыл бұрын

Thank you Sir is there any formula for calculated the shim of soft foot motor...

@rasetech 3 жыл бұрын

@@MuhammadAli-ev2ym I am not sure about the formula. But practically you can do it.

@jareddael5484 3 жыл бұрын

jaredlead33@gmail.com

@jagadishkumar7062 Жыл бұрын

Thanks for making this video

@kondayyanaiduaaa 3 жыл бұрын

Thank you for share the information

@user-jz5js7yl3d 3 жыл бұрын

V good

@divyanggandhi7115 3 жыл бұрын

Like it

@ebukareuben5785 3 жыл бұрын

Thanks a lot Sir,i have learnt a lot from your videos.Kudos to you,keep it up.

@rasetech 3 жыл бұрын

Thanks alot for your kind words.

@vikenkhalasi2445 3 жыл бұрын

You are doing a great job.

@rasetech 3 жыл бұрын

Thanks for your comment.

@ranjankumarsinha7410 3 жыл бұрын

Thanks for uploading knowledgeable video Pls keep it up We have learned more from your videos

@rasetech 3 жыл бұрын

Thanks alot for your comment and support. All the best for your future.

@alpha2285 3 жыл бұрын

Wow! Such a wonderful video to learn about soft foot ... really very useful and perfect one...thanks bro...keep it up...

@rasetech 3 жыл бұрын

Thanks alot for your valuable feedback. Good Luck.❤

@mohammadislam4373 3 жыл бұрын

Nice presentation for learning .please explain where we put the base of the magnetic stand during dial gauge measurement.

@deepsavaliya952 3 жыл бұрын

Sir, Great explanation..👍

@rasetech 3 жыл бұрын

Thank you for your valuable comment.

@veerapandian4398 3 жыл бұрын

Thank u nice work

@rasetech 3 жыл бұрын

Thank you bro❤

@shariquemallik5931 3 жыл бұрын

Thank u so much for uploading videos in english...Please further also upload videos in english

@rasetech 3 жыл бұрын

Thanks for your valuable comment.

@Studyenglishwithfun007 3 жыл бұрын

Good video

@rasetech 3 жыл бұрын

Thanks for your valuable comment.

@sanj9912 3 жыл бұрын

Nice useful presentation...Pls share more presentation on different topics in rotating & static equipments maintenance...sir..You have nice presentation skill.

@rasetech 3 жыл бұрын

Thanks for your valuable comment. And Many thanks for your support...❤

@muthukumarn9758 3 жыл бұрын

Great information.

@rasetech 3 жыл бұрын

Thank you ❤

@muthukumarn9758 3 жыл бұрын

@@rasetech sir pipe line flow calculat .blower three loop service . uploaded sir please

@muthukumarn9758 3 жыл бұрын

Your channel used lucky for me sir

@rasetech 3 жыл бұрын

@@muthukumarn9758 sure sir

@amitchoudhary3686 3 жыл бұрын

Your videoes are very informative...your hindi is also good ...keep uploading more videos....

@rasetech 3 жыл бұрын

Thank you very much for your support

@kondayyanaiduaaa 3 жыл бұрын

Sir please tell me I got the shaft foot reading 0.50mm how much shim can I add?

@danukaashan2735 3 жыл бұрын

Sir our ship going to change engine and gearbox.please can you tell me procedure for that

@rajeshrajerajesh2691 3 жыл бұрын

Super bro... slip gauge alignment panratha pathium oru video podunga bro

@rasetech 3 жыл бұрын

Slip gauge same procedure than bro. Feeler gauge use pandradhuku bathil. Neenga slip gauge use panna poringa avlo than bro difference.

@rajeshrajerajesh2691 3 жыл бұрын

@@rasetechcalculation method laam pakka diffrent ah irunthu bro athan ketten..

@mukeshkumar-ni6wx 3 жыл бұрын

thank u sir,please uplode face to face alinement method video ,please

@rasetech 3 жыл бұрын

Sure sir i will do it. Please stay tuned.

@aldorrymiftakaruna1264 3 жыл бұрын

hello sir, when we measuring soft foot, the motor and the pumps are coupled or not?

@antonyyohannan6477 5 ай бұрын

Cutted shims are allowed underneath the base frame? It's in an API 686?

@rasetech 5 ай бұрын

As per API 686 on Installation Angular Softfoot are not acceptable. Parallel softfoot only accepted.

@muthukumarn9758 3 жыл бұрын

Sir next pipe flow . blower clearance check video sir

@rasetech 3 жыл бұрын

Sure i will try... thanks for your comment.❤

@kondayyanaiduaaa 3 жыл бұрын

Sir incase shaft foot reading I get .50 mm how much shim can I add please tell me sir

@rasetech 3 жыл бұрын

See this video clearly you will get the answer... thank you....

@nirmalsurendranmenon7049 2 жыл бұрын

when we add shims for soft foot, will that disturb the vertical and horizontal alignment that was already completed?

@rasetech 2 жыл бұрын

Yes correct. Soft foot needs to be corrected before alignment.

@nirmalsurendranmenon7049 2 жыл бұрын

@@rasetech Ok let's say we corrected soft foot before alignment and then we start to do alignment where we determine by calculation that we have to add shims, so that may result in bringing the softfoot back again. So how do we resolve such situations?

@rasetech 2 жыл бұрын

@@nirmalsurendranmenon7049 Once you corrected your softfoot and shimed properly. then you will correct the misalignment by adding shims or removing shims equally from Front foot 2 legs and back foot 2 legs. So softfoot shims remains same at the moment. So It will not disturb again. First practically try it for the same. Then only its easy to understand. implement the same as practical. and Provide lockdown bolts with exact torque value for the bolt tighness.

@nirmalsurendranmenon7049 2 жыл бұрын

@@rasetech ok ji thanks. Will do

@Apriest99 3 жыл бұрын

Sir is there angular shim available for correcting angular soft foot if not then how can it be done🙏pls answer sir

@rasetech 3 жыл бұрын

Readymade shims are available Or you can cut from shim sheets...

@Apriest99 3 жыл бұрын

@@rasetech thankyou sir🙏

@DilipKumar-sp2fg 2 жыл бұрын

But as per api 686, step shim or cut shim can not be used for soft foot correction.

@rasetech 2 жыл бұрын

Thanks for the information. Yes You are right Cut shims are not allowed from construction and commissioning time but unfortunately some of angular soft foots will occurs on the operation and maintenance time period. So from maintenance you cant rewok on the base with short period. in this case we should use cut shims to cover angular soft foot cum parallel softfoot. Theoretically you can say but practically it will not work out. Thanks for the comment. I will appreciate for the same.❤

@DilipKumar-sp2fg 2 жыл бұрын

@@rasetech agreed, to reduce the angular soof foot in future, for that during construction phase motor base blue matching as well as foot checked without shim . for that used dial indicator over motor base or coupling and check soft foot for all 4 foot and reading must be within 0.05mm. In this way we reduce possibility the angular soft foot for future case

@rasetech 2 жыл бұрын

Great. Thank you very much...❤