Nice! I can't believe I've been doing it the old-fashioned way without this thing.

thanks for taking time and show whole latch installation, those small details are the big value.

Wow that is freakin cool I saw it not too long ago at Home Depot but i wasn’t convinced to buy it But what convinced me now not only how you explained how to use it but even the incorporated chisel in the jig You actually spoon fed how to use this jig A million times thanks HOME DEPOT YOU NEED TO PAY THIS GUY IMMEDIATELY 👍👍

Not a bad gadget really, ryobi are underrated they do a lot of decent quality tools

Great video! I came across this tool yesterday and was wondering how it worked. Your video was very informative and to the point. Thanks!

I have this tool and it works pretty good but did have a couple tear outs of the wood here and there. Great tool a must for any DYIer or professional. I also saw you used the door hinge router template they sell. I just discovered this had to go to 4 Home Depots to find one. Worth it's weight in gold. I ordered 3 more so I could set them up on one door with two or three hinges rout them all without having to move the one tool around got one extra in case one gets broken.

Not sure why so many negative comments on here. Very thorough and is clear you are a bit of a perfectionist, nothing wrong with that! Especially with some of the sloppy diy stuff you can find on here. Thanks for the in depth video. 👍

Thanks for this very useful video. Just what I needed.

Thanks needed that - especially pushing out the scoring blades - bit of a complicated instrument - a good video like this is needed.

I ordered one of those just while ago. Good video. Thank you.

Thanks boss, im goin to home depot in the morning and gonna get it incase i ever need it

Thank you bro for the great details

Nice. Thanks for the tips on the Ryobi tool.

Great video. Thank you.

Thanks Ken....you saved my marriage :)

Thanks for this video. I just ordered 3 doors at home depot. I was thinking of hiring someone to do this for me, but watching your video, i know i can do this.

It’s funny how all of these installation videos neglect or omit how to use this tool to mortise the door jamb itself.

Thank you so much

Wow someone that's actually helpful. Thanks brother.

Thank you

glue a lair of felt or something to the top to reduce that couple of mill from the depth

This was so helpful !!!!

thank you for thisvideo i am going to buy thie ryobi tools,afterv a while crocodile

Thank u

Thanks great video

I like the router template better. Easier. Quicker. Cleaner look. Perfect depth

I really wish I would’ve known this tool existed... I fucked up my door a little, but it’s a $40.00 door and it’s not that bad. I’m getting this though for future projects.

s00per :)

Go to the 5 minute mark.

I saw another video on this tool and the guy went crazy hammering step 1 and on step 2 he pushed the tool as far as he could and laid into it. When he was done it looked twice as deep as the striker backing plate. I have 8 solid oak doors to do so I was looking for something to make it more consistent. I like the 1st part, but as far as the 2nd, I think a really sharp chisel would do better. Work from the finished edge to the center. I also cringed when during the 2nd part you get to the end of the cut and have to remove the material. I just know if it were me something would splinter.

How on earth did we manage for a couple of hundred years or so before Ryobi?

pretty easy looking jig - it didn't put the marked outline in the center of the door (looks tight to top edge when installing)

Good Job...Regards

He noticed that when he puts it all the way in it's too deep so he lifts it and then it's not deep enough. That's what she said btw. No pun intended.😂

Cool, but I bought a router to install hinges and am using it to route out that hole.

May don't lift up when hammering sideways and you won't have to spend time chiseling.

Can the tool be use for the strike plate??

Does it work on metal doors?

Did you mention if you like it??? Hahaha

so ...do you like it?

wrong in every way having used these for a number of years i have just found out that if your a professional and use these products you have no warranty claim according to the uk ryobi site.

Nice tool demo. Your chisel needs to be sharpen, looks really dull. :-)

Good video, however I think you should spend half hour sharpening your chisels. The tool itself is probably ok for DIYers and wouldn't be much use in the Uk. I think I would have been faster using a couple of sharp chisels.

Please look at the camera lens, not the screen. You need to portray that you are talking to an audience.

What a palaver. Slower than doing it with a chisel...

About 10 minutes too long.......

So.....the tool really doesn't work. If you have to spend so much time hand working the fit.

Why are you wearing gloves

How thick is your door? 1 and 3/8"?? Ffs

What a load of crap could have done that with chisel in half the time

Should've called your channel bucktooth training

So what I took from this video was you’re reviewing a tool you don’t trust to do the job so you took a 2 step process and turned it into a 14 step process with your extra chisels. “Imma put this all the way in then pull out a bit now for a test fit, oh wait it’s not deep enough lemme put the tool ask the way in and do it again “ 😂. I wasted my time watching this video thx