Good job young man. In today’s world where most kids your age are inside the house gaming. You’re making it happen with wrenches and learning. The lessons you learn today, will last you a lifetime and help you fix your own stuff without having to pay someone to do everything for you. You didn’t need to cut the end off the throttle cable. Just needed to use a cut off wheel and cut a slit in the bracket, slide the cable in and the barrel at the end locks up to the bracket. No brass stops needed. Definitely need to change the gearing. Simple sprocket change should do it. Also might want to incorporate a chain tensioner gear on the swing arm area of the frame. This will carry the chain and keep it off the frame.

With those type of engines I use a 2 stroke clutch cable as a throttle cable. They don't have a little ball at the end that needs to be cut off. So you don't have to deal with The Frayed Ends.

Good job. Motorizing a bicycle is an up hill climb all the way. Lots of grinding and twisting, but it can be done. Built 11 choppers with the 80cc kit. It got easier after each build. Mmmm... you can install foot rests on the forks. Good luck

Just bought myself one of these yesterday. Sounds amazing with a high flow straight pipe. You'll need to open ip the stock exhaust port to fit one but it make them deep toned.

It seems like its geared a bit tall if you get a clutch with a smaller sprocket, get a bigger sprocket for the rear wheel or do both it should pull harder

I just found a stingray chopper a lady is selling for 60 bucks I'm taking my bbr 80cc tuning off and mounted onto the chopper this is going to be fun fun little projects

Good job 👍👍👍 sounds like a chopper .

Awsome build man!! I think a jackshaft would do you great as this thing looks to be geared to have a higher top end.

The smile on the young man's face, Kool

Your Clutch is placed backwards you would need to kick that engine out more so you can flip that clutch the right way also think about upgrading the clutch spring so you can pick up that engagement also if you stick with that centrifugal clutch then I would up the rear sprocket/ final drive sprocket start around 50-60 tooth ,or you could just upgrade and go to a torque Converter like most of our builds. Other than that, good job, you have done excellent. your mind has good problem solving skills.

What you need is a Torque Converter kit. You bolt up a common shaft system with the old friction clutch then replace the friction clutch with the torque converter system and it will ride like a high speed snowmobile. I had one and it really go's a lot faster than a friction clutch does. It will also allow you off road performance and dirt riding is unbelievable just don't get dirt in the back pulley or you have to replace the sliders.

*Sold-Er* ...Y'know what? That's how it's spelled - Ain't even trippin, Homie.

Fuck me that's a good looking bike! Personally I think the rusty rugged surface looks awesome. :D

Ive got one of these, a black one. Gonna motorize it too. I want a dependable model and no weld.

Great job!!!

for the frame you wanna sand it down to its base coat and then spray your primer 2 coats to be safe and after that whatever color you want will go on 2-3 coats and you should be good of rust and chipping im making the same bike now clutch 125cc manual 4 gears up

Sounds like a bubble machine geez man you need an exhaust

Just an idea, spray the bike with vinnegar, like mist the whole thing, then hit it with fine grit.

If ur wonder to cure the paint job reasoned ur frame then put one heavy coat of clear twice I like a good rusty look

A wire brush bit on a drill will remove the rust and put primer and paint on the frame to protect from rust or put a clear cot of paint for protection

Try some Rust-Oleum and then clear a coat over that but you're going to want to do a couple coats

Rhino liner!!! Would be dope I’m actually getting ready to start the same project with my stingray always wanted to but now they have so much more just you think it and you can find it online usually

Very very cool good for you buddy 👍👍👍

You might wont to cover that hole in the frame by the motor before rust set inside the pipe. Rain can also cause more rust if it gets inside. And for rust problem, clean all rust off then spray latex oil base paint on it.

There's a chemical treatment that i prep bare metal surfaces with when I work on car panels. It's called metal dioxidizer, once applied to a bare metal surface, it makes it turn blue in colour hence protecting from exposure to moisture and the elements. New replacement and rust repair panels for cars also come from the manufacturer with this treatment applied to the surfaces... I swear by it as I apply the deoxidizer even before the primer as a second layer of protection... try it.

I cut the seat post tube out and used 212. Used old 1 inch riser mountain bike handlebars for foot pegs. Had a 79 on my 20inch wheel adult trike bike, but slow takeoff. Even with 60 tooth rear sprocket

Stick a pair of old 1 Inch rise huffy mountain bike handlebars through that hole for foot pegs & duct tape em. Honestly I had to switch my motor out to a 212. My 79cc went like 30 but it took forever. With the 212 it does 50. Right quick

Try some used motor oil on the metal keeps the o oven off of it

*GRANDPA WANTS ME TO TELL YOU* That the bike needs a set of Ape Hangers and springer forks once you get the paint and performance issues worked out. Grandpa was impressed with your work kiddo, that means more than you know. Grandpa is old, salty, and battle scarred and isn't impressed easily. He say you remind him when he was tinkering with old Indian and HOG pieces and parts way back in the day.

To do bare stell you'll want to clean the metal with a dioxidizer before you prime and clear coat it.. I wanted to do bare steel on mine till I realized how much work goes into it

Very good you are on your way to fun city

make sure the frame is clean and dry use an acetone based cleaner so it cleans oil off and drys fast wear rubber gloves apply a primer coat i belive some primers come in clear than apply 2-3 coats of clear

That’s awesome man

Chain tensioner. Your chain routing was under the frame instead of above the lower frame rail. You should have use a cvt transmission, that rear wheel is heavy. You will eventually have to find a rear sprocket adapter or jackshaft kit. I just finished an identical build.

Sounds like the willy Wonka bubble Car at idle LOL *Cough* Very manly! LOL

Did you use interior clear coat, or did you clear over the surface rust before it was visible to the eye. Use a small "ell" bracket with a twist in it for orientation of cable to where you need it. The bicycle shop sells the little cable end that crimps on end of cable, I bought 25 of them for $4 dollars You need a chain tensioner of some sort, I've seen numerous styles for the chopper. Try the exhaust adapter and the 2 stroke pipe you can get at gasbike.com. Also you seem to need gov. bypass or delete. Your clutch is fine. I am impressed you got it going and it runs, well done, just work out the bugs and you'll have a fun bike.

👏👏🤝

You need to put that chain above the frame around the tire or it's gonna run and cut your frame

I’m in the process of building one right now

Honestly I think the rust makes it look kind of cool. By the way your bike is awesome!

is it possible to keep the crank? they might confiscate that bike if the pedal assist isnt working.

We use to have a product called Jospho rust killer . I t was some kind of acid .

You need penetrol to stop the rust then maintain the look with linseed oil.

Rustolium sells rust reformer. Clear liquid and inhibits rust.

Whys it look like it barely moves under its own power? Not talking down. Genuinely curious. Looks like its super bogged down.

Great job bud.

Could you make a video showing what what type of sprocket connectors you put on back tire.

i got a chopper with 208cc 7hp gets up to 70 mph

"it's needs this bullshit and that bullshit" It needs a rear sprocket with 3x the teeth... the end.

I know this video is mad old but you should put some steelit paint on it

Was trying to find a mini chopper frame but looked normal bicycle frames would that work?

And I’m thinking I’m gonna do the liner with mine and figure out something to also pop it out just not sure may light brush on the top on my texture

Oil base clear coat and do at least three coats

Why don't someone build one of these with a fully working cision v twin pan head Harley Davidson engine for this with a working 5 speed transmission for it all belt drive

How did u did the front brakes?

Clear poder

How do u install stand

Cool project man. The motor would have been better mounted facing the other way with the chain on the other side. Also you need some pegs bro

I need other Big sproker for the motor

Rustoleum, flat black rust reformer?

Is u use ojo 28 mm carb u delete the gobernor and u have more aceleretion more power w after market ojo 28 mm carbutetor

only way to fix that paint is powder paint it...cost a few bucks but worth it

Ugly is the new pretty!!!

Polish it and wipe it down With boiled linseed oil?

Paint it chrome then clear coat

I use WD-40 on mine and it works

Monster you need to prime it

What speed you think you’ll be able to get eventually

Needs a exsorst pretty cool tho

The sproker maibe 48 toth

Do you know how to make steering much easier and safer. With my chopper it just feels like it’s going left and right

6 words I don’t wanna hear you say before you ride this “ hold my beer and watch this”

Buy em 2L 3L gas tank from Amazon

What clutches/gearboxes are available for this motor? Have you thought about the manual clutch from sportsman?

IoI You need to prime it and paint before ya add cIear coat xD - Prime it atIeast - it won't stick to bare steeI

Tighten that chain!

Chain 2 long need Chain tensioner

YOOOOOOOO I fuckin brought this bike off thos guy!!!!!

Hey paint that thing Dark Silver hey i G hey

yo good video. i have a chopper bike just like this. but i don’t know where to buy the best motor so that it will fit this bike good. also i wanted to know how i can put the motor on without taking pedals off. iv seen people with motors still have there pedals on. would be great to get advice. i would email you but i don’t know you’re email

Tell him

Is that the 5/8 clutch

what is rear wheel size?????

where did you find the mount?

Hammer silver

Use Coca-Cola that'll take out the rust

Rust Is just free weight reduction

Car primer nd paint it

Had no power at all. Like zero. I bet your burning the clutch bad to

Why is it called a occ chopper its a insult to scwhinn

Wanna race?

Where did you get the motor mount?

El presio

Flip that exhaust upside down so you don’t have that blowing in your face

Definitely geared too high.

Whats you gear ratio

Boat paint

Lol 12 minutes of talking, for less than 2 minutes of riding.good one

Is better eliniminated the gobernor

You can walk faster 🤦🏽‍♂️