Sherwin Williams Gallery Series vs Emerald Urethane Trim via HVLP

Рет қаралды 7,946

Күн бұрын

In this video I use Sherwin WIlliams' Gallery Series for the first time where I compare it to Emerald Urethane Trim. The HVLP guns used in this video are available at amzn.to/3P8338Q

Пікірлер: 38

@jamiedorsey4167 3 ай бұрын

I do repaints. I used Gallery for the first time about a month ago refinishing cabinets. I loved it, the dry time and the hardness is also what stood out to me and the availability makes it way more convenient than other high end cabinet paints. I was worried about how well it hung and whether it would run on me, didn't have much of a problem with that once I got the hang of it. It also has a pretty low odor which is a plus when spraying in a home. I spray my doors laying down and use the red bondo glazing to fill in imperfections after primer. A couple things I found was that two coats often didn't hide the red bondo and I had to hit several of the doors with a third. Also, putting it on too thick causes it to crackle, it sands out and disappears with another coat though. I used an airless spray with a .310 FF tip, but may try a .308 next time. Overall I loved it and will likely be using it as my cabinet paint unless something better comes along.

@TheWebbRanch 3 ай бұрын

I have to agree with you in that I don't think I get the same coverage with the Gallery over the Emerald

@seanb1321 2 күн бұрын

Thanks!

@honeyforce996 7 күн бұрын

I'd love to see you compare it to BM Command. AFAIK Gallery is like $143/gal list (plus the crosslinker if desired). That's a freaking lot for a 1k product. I guess people really like wb cleanup. I think Command is like $75-90/gal.

@jimfeaster4837 3 ай бұрын

Great video

@nothingsimpostleble1593 20 күн бұрын

Yeah I've been a painter for 15 years...do about 7-10 cab jobs a years and usually only use emerald. I started a set of cabs on Monday and decided to use GS, noticed it was pretty thin. Too see you soup it up even more was pretty insane 😂 like woah.... then low and behold you had runs... Then your gun was spitting i think because you didnt clean it good enough last time idk.... As far as primer, i use pigmented shellac or If i were you. Maybe a sanding sealer.. That kilz primer is garbageee

@michaeldurham8856 4 ай бұрын

Thank you for making this video! I've heard so little real world info and even less from SW about the Gallery Series. It sounds like for my DIY level of experience the gallery series may dry too quick and cause headaches for those with slow workflow like me. Obviously the opposite end of the spectrum from your production scenario.

@madboomr- 12 күн бұрын

water CAN be applied for spray applictions but isnt necessary how come people add water to their paint they spray? I have yet to do it.

@LeAnnHarbaum 2 ай бұрын

How is the sheen comparable between the two? Is the satin sheen of EU close to the Gallery sheen 20?

@tmilholin7552 Ай бұрын

Always spray test your gun on paper or a piece of wood first and always use grain filler on raw wood then sand, then prime. wood filler is $8

@a.preston3699 4 ай бұрын

I have an hvlp I've used EU with a 2.5mm tip that I don't have to thin as much. Also have a 1.4 and 2.0mm I have not sprayed with. Do you think the 1.4mm would do good with the gallery?

@TheWebbRanch 4 ай бұрын

It's probably too small. I'm using a 1.8 now unthinned.

@alexandrucristian6160 3 ай бұрын

1.4 will work I use 1.4 #3 from Greco

@alexandrucristian6160 3 ай бұрын

Graco

@msk3905 Ай бұрын

Just used anchors aweigh (navy blue) emerald urethane on an exterior door and boy am I disappointed! The good; it sprayed nice right out of can but ended up thinning less than 5% for a better spray, leveled out great. The bad after letting dry for two days it scratches really easy and is difficult to clean. I wanted to wipe some dirt off dead bolt where my finger nail ever so slightly ran across door leaving a scratch. There were some handprints on door after install so wanted to clean so saturated a paper towel with water and it left smug marks where i lightly wiped. My normal advance go to would never do this and what a disappointment!

@dubeckvids3110 3 ай бұрын

Hello, what tip size were you using for the Gallery series?

@TheWebbRanch 3 ай бұрын

I'm using a 1.8 currently and it's coming out pretty fast. I may give my 1.4 a go and see what happens

@johncasper3536 2 ай бұрын

How is the VOC on the Gallery paint? Thanks John

@TheWebbRanch 2 ай бұрын

About the same as Emerald. Hardly noticeable. It does smell distinctly different from emerald though.

@davidakers9030 Ай бұрын

According to a spec sheet i got from SW V.O.C. (less exempt solvents) 178/litre, 1.48 lbs. per gallon. I was told it had more than double the VOC than the Emerald Urethane.

@johncasper3536 Ай бұрын

@@davidakers9030 Thanks

@nickthegazerofsouls Ай бұрын

What I really want to know is which one is more durable in the long term

@TheWebbRanch Ай бұрын

They are both still in service and the bigger one has started to grow on me even though I STILL prefer the k4.

@sharonvriend7531 4 ай бұрын

Hello, have you sprayed the gallery with an airless system like a Graco Magnum X5 with a 310 LL FP? Or should we stick to our Fuji HVLP? We’re just having such orange peeling with our HVLP

@TheWebbRanch 4 ай бұрын

I have not. I have three airless here but hate them all so they sit in a drawer lol

@markzelinskiphotography3768 4 ай бұрын

It’s great with airless FFLP tips. Have used it with GX19 and Quickshot. Almost as good as Centurion finishes. It’s WAY smoother than Emerald Urethane. Every EU I’ve used has a gritty texture. Not the case with Gallery. 308 tip works nice.

@jessekrestal1081 Ай бұрын

turn pressure down to a point that you're getting tails again in the fflp tip. i've sprayed it in a few kitchens now, you can easily over pressurize it still and most people do use their airless the wrong way in the sense they turn the pressure all the way up and maybe sometimes back it down a little. you're supposed to turn it down until it has tails then ever so slightly more pressure and thats it. you fundamentally spray differently with this paint in an airless setup.