We cannot take all of the credit. The gent in the video really nailed the process

Hello, you are welcome! Are you seeking a full skull mold or are you asking how much each casted skull might sell for?

@@PacificMoldDesign Thank you for getting back to me, I appreciate it. I'm looking for the full skull mold. I went to your webpage, the full skull that you have is pretty much exactly what I was looking for. I'm brand new to this whole art thing. (I used to be half decent...clear back in my high school days) I was in a bad accident when hit by someone texting and driving and unfortunately permanently disabled. Was/am looking to try to do art projects to focus on something other than pain. But with being on disability, I can't afford to spend my money on such "luxuries"....maybe some day

Our phone, email and all forms of messenger are available to you. Instruction manuals are useless when you consider the many ways to approach a project. What material are you wanting to cast? I assume foam? If this is the case, please do a partial test. ABS is rather porous and foam tends to stick to the molds.

Hi thanks for your replies, I bought the 2 part fence post foam and the bond builder latex shown in this video, I was unable to find any wax release, yours is sold out, which is the route I wanted to take, seemed like the latex was a more time consuming step, is there pros to using latex vs wax? Are they both paintable afterwards

Goodness, quite a few can be achieved. I would imagine 30-40

Each foam manufacturer has a different rating for outdoor use. I would imagine a cement based product would be much more suitable.

Thing is latex doesn't hold up to uv light etc.... just look at elastic bands left out in the sun....

The Great Stuff is really tacky. If you must try it, use a carnauba "wax"...a few layers.

Any idea on how to remove spray foam from the mold. Oops

If you are using cement based products, absolutely🤘🏼

@@PacificMoldDesign I just bought some skull molds and I am ready to start making some skulls for next Halloween. Thanks for the tip

There was a latex series of layers added, cured then removed. Let’s call that a shell or mask. You then place the cured latex shell or mask back into the mold and the load it with the poly foam. Now you have an ultra lightweight skull that can be colored up.

@@PacificMoldDesign is this to say it's not paintable if it doesn't have a latex shell on it?

@@kell2resq you should remove the latex before adding the foam because the latex could rip if removed as one piece. Once removed, you can paint the latex like a typical latex mask.

Mike yes, you have to use a wax based release agent. We have a Honey Wax or you can find some others online. Find a carnauba based wax and give the molds a few coats. If you are using Great Stuff, trip up on the release, the stuff is tacky.

Just curious if you tried it this way, did it work?

These are the 8" molds

@@PacificMoldDesign oh ok...oops I just ordered the 11 inch

@@PacificMoldDesign you said the 8 inch are more life size correct?

Perspective is everything. If you use the 11" mold and tilt it forward during casting the face size is more accurate that the 8". The 8" mold is good if you just want something 8" in total size. I prefer the larger for the realism.

@@PacificMoldDesign Alright cool I will just stick with 11 inch.

Joshua that is essentially the same material. If you choose to use pure foam, you will need a wax release agent. We carry "Honey Wax".

Pacific Mold Design would that still work with the latex layer too? Been using the polyurethane with the honey wax but it always hasn’t released uniformly like I’m seeing with this. How much would you spray in for this? And also while I have a moment, what’s a good way to clean them

Joshua The latex layer is a surefire way to contain the material. If you are using the wax, there meeds to be 3-4 solid coats before pouring. If you are using a spray, it may be the wrong stuff. Cleaning, send my some photos of what you are fighting. Pacificmolds@gmail.com

Pacific Mold Design thank you. When I get home today I will

Pacific Mold Design it’s mostly residual polyurethane before I found out about the honey wax

At least you said PLEASE.

SORRY JUST LOSING IT WITH THESE VIDS Freezing UP ON MY PH TAKING 4 EVER ,THEN THE NEXT VIDEO PLAYS RT THROUGH ,THEN A VERT PH VID TODAY ?? ADDS TO ALREADY AGRIVATED FIGHTING WITH WIFE , HAD A STROKE , MUSCLE SPASTICITY N SPASM , SO THERE THAT SO SO SORRY LOVE YOUR VID JUST WANT TO ENJOY WHAT I SEE 👁️👁️ SO SORRY