Smart W451 Clutch Actuator Installation And Clutch Relearning

Рет қаралды 47,687

2 жыл бұрын

Clutch actuator installation and Relearning procedure is carried out after replacing Clutch kit on Smart Fortwo Coupe 451 1.0 L
but this procedure is applied to all smart with 451 series chassis, so i followed service manual instruction but there was mentioning about Relearning procedure so, until i didn't relearn the Clutch to the transmission Ecu the DTC couldn't erased the DTC was erased after the Clutch Relearning procedure completed.
you can check in other smart related videos clicking on the links given below.
• Smart Fortwo Coupe W45...
• Smart Fortwo W451 High...
• Smart Fortwo W451 High...
• Smart Fortwo Coupe W45...
• Smart Fortwo Coupe W45...
• Smart Fortwo Coupe W4...
Disclaimer:
this video only contains tips and recommendations that could be useful when carrying out vehicle repairs or replacement parts, STANHOPE AUTO REPAIR CENTRE WARDAK is not liable for any damage, harm injury or property damage incurred while carrying out repairs or replacement that are a result of incorrect use or misinterpretation of the provided information purposes only and does not guarantee achievement of specific result. The user is personally liable for incorrect use of repair equipment, tools or vehicle parts, in particular, when this use poses the risk of injury. STANHOPE AUTO REPAIR CENTRE WARDAK strongly recommends being careful and adhering to the safety rules when doing any repair or replacement.

Пікірлер: 42

@MrTottanham Жыл бұрын

you dont need a star diagnostic tool to do it, you can simple disconnect the battery for a few hours and when you connect it back and turn ignition on (do not start car) you will hear the actuator will relearn itself, once is finished few secound later you can start the car

@jaguarthegloman4158 11 ай бұрын

How long should I wait til I start it back up?

@xrayhead Жыл бұрын

Really good video that shows how complicated these little cars are!!!

@stanhopeautorepaircentrewardak Жыл бұрын

Thanks for watching our channel ☺️

@cmnightfaces Жыл бұрын

Thanks, I have a 2012 smart 140,+++ miles on mind. Will keep in mind.

@younessbenassou7494 Жыл бұрын

Thank you from France for this vidéo

@stanhopeautorepaircentrewardak Жыл бұрын

Thanks for watching our channel ☺️

@alexroman8386 2 жыл бұрын

great video it helped me out alot

@stanhopeautorepaircentrewardak 2 жыл бұрын

Thanks for watching our channel

@patata2002 2 жыл бұрын

Thanks for share. I want to buy a MK808 but it don’t work with smart and clutch??

@petersimms4982 2 жыл бұрын

smashing video

@stanhopeautorepaircentrewardak 2 жыл бұрын

Thanks for watching our channel 😊

@rowdydude957 2 жыл бұрын

Don't you think that the computer programs are just to monitor what the computer module is doing and just following the steps is enough for relearn?

@paulmoss507 Жыл бұрын

Can you let me know what scanner/diagnostic tool you used? I'm needing to do the same and assumed the only option was to purchase an MB STAR unit.

@stanhopeautorepaircentrewardak Жыл бұрын

I used snap on verus with 13.2 software version for this particular vehicle. Topdon Phoenix plus Scanner can also do the job according to my experience, MB star diagnostic tool can do the job too.

@Alpha_Betz 2 жыл бұрын

What scanner are you using? Is it required to teach bite point after install?

@stanhopeautorepaircentrewardak 2 жыл бұрын

Thanks for watching our channel For this particular task i used snap on verus and also the scanner will prompt you itself to the Clutch Relearning procedure to the end.

@Alpha_Betz 2 жыл бұрын

Oh ok. That’s what I had a shop do last time, just was hoping to not have to spend $100 again. Lol thanks

@rafaelaguilar1329 10 ай бұрын

i have the problem sometimes no gears Reverse

@gplusgplus2286 10 ай бұрын

Very nice video. Have bought the clutch kit but now need to find a programmer for the clutch adaptation... I only have experience with vcds (vw/audi) Shop asked 750€ for clutch replacement.

@stanhopeautorepaircentrewardak 10 ай бұрын

Thanks for watching our channel ☺️

@ilvale6439 7 ай бұрын

The "clutch learning" is mandatory only when the clutch it was changed or also when the clutch actuator was changed? Thank you

@stanhopeautorepaircentrewardak 7 ай бұрын

Thanks for watching our channel This video was uploaded long ago. I followed the scanner instruction, and the scanner will guide you in both cases what to do.

@ilvale6439 7 ай бұрын

@@stanhopeautorepaircentrewardak thank you so much!!

@LuisVazquez-kj1ym 2 жыл бұрын

Great thanks, i want to learn use wow software help

@stanhopeautorepaircentrewardak 2 жыл бұрын

Thanks for watching our channel

@gabrieldumea5534 Жыл бұрын

Hello, I have a mitsubishi colt, recently I changed the clutch, everything is ok, while I'm driving, when the gearbox changes from gear 2 to gear 3, there is a noise like a crack and then it goes into gear, do you have any idea what it could be? possible to be from the actuator? Thanks a lot

@ugiit8930 Жыл бұрын

If the Clutch is new you have to relearn it. If the Clutch is not changed you have to next time..

@gabrieldumea5534 Жыл бұрын

@@ugiit8930 Thank you,I will do tomorrow cheers

@ugiit8930 Жыл бұрын

@@gabrieldumea5534 If it doesnt work you have to change the actuator. I had to also. Sometimes grease doesnt help

@gabrieldumea5534 Жыл бұрын

@@ugiit8930 Do you know any garage to fix that for my?im located in Dartfort. Thank you

@ugiit8930 Жыл бұрын

@@gabrieldumea5534 sorry bro im from germany. paid 100 for clutch in german Amazon. 200€ in the shop to repair. Now i paid 225€ for actuator and nothing to install cause its done in 5 minutes with 3 bolts