Smoke? Hot Smell from Wheels? Check Your Brakes! Diagnosing Seized Brake Calipers

Рет қаралды 234,338

1A Auto: Repair Tips & Secrets Only Mechanics Know

Күн бұрын

For More Info visit us at: 1aau.to/h/cKU/
Do you see smoke, smell a hot or burning smell coming from your wheels? Can you feel heat radiating off your brake rotors? The problem is likely a seized brake caliper! When brake calipers stick, or seize up, the brake pads remain in contact with the brake rotor while your drive, which creates lots of friction and head. It's basically like driving around with your foot on the brake pedal the whole time! In this video, hot smelly brakes lead Andy to diagnose the brake caliper, where he discovers rusted slider pins. The slider pins need to move in and out freely. If they get stuck, the brake caliper can remain clamped down on the brake rotor, which in turn heat up the brakes excessively. Andy points out the problem, shows you how you might be able to unstick and repair the rusted sliders, but ultimately replaces the caliper entirely, which is the safest option.
For more great diagnostic videos check out this playlist:
• Driveway Diagnostics!
0:00 Diagnosing a Seized Brake Caliper
3:45 Removing the Stuck Slider Pin
8:31 Clean the Caliper Slider Pin and Bracket
12:30 Or Replace the Caliper!
For More Info visit us at 1aau.to/h/cKU/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 114

@1AAuto 2 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@Just_J_ 8 ай бұрын

think u just saved my life, didn't know what was causing my brakes to overheat and smoke

@coburn_karma 2 жыл бұрын

Very rare to see caliper repair these days with low priced new calipers on the market....thank you for taking the time to share.

@pareeks 5 ай бұрын

I'm just in awe of all the tools and machinery you have at your disposal. You have even got a gas torch of high grade! Marksmanship is on point as well❤

@AZHighlandHomestead Жыл бұрын

Video really shows how valuable the cheap rebuilt calipers are for the money

@cardo1111 2 жыл бұрын

Definitely one of the best auto repair channels on KZfaq 🔧🧰👍🏽

@TheKramer841 Жыл бұрын

Thank you. I'm trying to do a similar job and being refreshed on basics that work saved me a lot of time getting up and down and fighting stuck parts. I'm a forever injured guy. Again, thank you.

@michaelreeves8164 2 жыл бұрын

Very professional. I was happy you didn't reuse the old caliper and pins. Thanks for the tips.

@BMMPMI Жыл бұрын

Thanks 1A! Hope you have a good day.

@josedelossantos2428 2 жыл бұрын

Love your video tips. very instructional informative and educational. Thank You !!!!!

@josephkasprzyk4758 Жыл бұрын

First off. That’s a very clean garage!!! Secondly. You were very helpful to me! Thanks

@andygirke846 2 жыл бұрын

Thanks Andy, Nice Demo.

@OldSchoolNoe 2 жыл бұрын

Fantastic! So many skills on display. Quick quiz for the viewers interested in a career in automotive. (Answers found in video) 1. What type of brake fluid is commonly used? 2. What type of grease is used on the caliper slide pins? 3. To "bleed" the brakes you loosen the _______. 4. True or False: A torn caliper slide pin boot is OK and should be left alone. 5. Two technicians are discussing a seized brake caliper. Technician A says the brake fluid needs to be changed. Technician B says a slide pin could be the cause. Which technician is correct?

@GreasyWop 2 жыл бұрын

dot 3 I use 3M silicone paste, but you can also use brake/caliper grease that nipple looking bolt on the back lol False Tech B

@MrHank5899 4 ай бұрын

This video seems better than your other ones

@1AAuto 4 ай бұрын

+@MrHank5899 Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@flakociclon44 2 жыл бұрын

Thanks for the video, keep having problem on my 99 GMC Yukon 2wd

@OSRS_KQs Жыл бұрын

Just figured mine out. The caliper piston is the style that needs rotated to collapse it for new pads. However, there are 4 recesses on the face of the piston for rotating it, and the recess has to line up with a tab on the brake pad that the scratch warning plate sits on. It was causing uneven pressure on the pads so they seized pretty hard and got hot.

@richardyap7873 2 жыл бұрын

You are a cool guy. Doing so much and yet keeping your composure. Liked.

@mybrotherscout3661 2 жыл бұрын

Thank you! Just so happens I will be working on my brakes today.

@landshass2849 7 ай бұрын

I found it time consuming to get a new bracket because it requires new rubber boots and new pins. So I just order a caliper bracket set with pins and rubbers included. So it's a good time to gravity bleed the brakes.

@charleschiu1383 Жыл бұрын

Excellence. Very instructional video.

@OmarSharif-js8tx 2 ай бұрын

I lived to way you explained everything excellent bro👍🏼

@Alesia2020 Ай бұрын

This video was so awesome! Thank you for taking it step by step clearly. I now have a better understanding of what do in this situation.

@1AAuto Ай бұрын

+@Alesia2020 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

@dwightlee6164 2 жыл бұрын

By the way.. you uploaded on the thanksgiving day. Working hard.. Thanks !

@theodorerinehart781 2 жыл бұрын

Excellent job

@oscarrox Ай бұрын

Used car owner here. I've Just been told the offside rear brake has been binding (not binding right now), and has caused heat damage, replacement of disk and pad reccomended. £400/$495, Kia Stonic (UK), through a Kia dealership, that's a lot of money!

@PRO4XKEV 2 жыл бұрын

Great work.

@user-dd3kj8ji3c 11 ай бұрын

Thank you so much for your help!!!👍👍

@SusannahCrossman Жыл бұрын

Thank you so much for your video - which I watched yesterday. My beloved car has a brake issue - I now think it's probably a seized caliper or the slider pins, BUT, may I ask ... the issue arose after a loud BANG which seemed to come from, I thought, offside front or offside underneath my car - the wheel/brake/caliper that's seized is the nearside rear! At first I thought maybe something had punctured a tyre but, after parking back up (had only travelled a few yards out of the parking area) and leaving my car for a while there were no issues with any of the tyres. Then my son and I thought maybe the handbrake cable had snapped but the handbrake still works - although floppy when first engaging it soon catches the ratchets as the lever rises and keeps car stable. My car seemed to drive normally when I took for a short test drive (half mile max, 20mph), although sounded as though brake pads were worn, BUT nearside rear brake disc (rotor) HOT, HOT, HOT!! After seeing your video I'm sure it's a seized caliper, but my question is ... have you ever known a loud BANG prior to caliper seizing? I wonder if something has snapped INSIDE the caliper and it now won't disengage - I wonder if that might be a possibility, would you know? Wheel/rotor movement, nearside rear, after my car has been parked a couple of days, is almost totally impossible now! About four hours prior to the loud BANG and issues arising, I'd been out on a twentyfive mile round trip and there didn't seem to be any problems! If you have any suggestions I really would be so grateful as we don't have any local garages who would be willing to take a look (my car is 2007 and local garages have 'decided' it's too old to bother with!! To me, of course, my beloved car is PRICELESS)! THANK YOU SO MUCH, in advance - and thank you, again, for your wonderfully informative video!

@banaweekidane2630 7 күн бұрын

My god that garage is clean.....

@user-dv5ye9tb8t 8 ай бұрын

Wait. I should buy simikar burning device 😅.amazing job.thanks for sharing.

@apmorales7187 Жыл бұрын

Good job amigo 👍

@extramail850 2 жыл бұрын

Great video!

@taddeojudemugagga2306 2 жыл бұрын

Great, job thank you sir.👍

@nikkilovetheyardsale-again2608 Күн бұрын

I had to edit this post. The rubber glove trick is so got damned amazing and beautiful 🥰 I can't tell you guys how much you have saved my life. You guys taught me how to do my own breaks, Fix my U joints on my drive shaft, how to do my hubs and wheel bearings also you saved mine and maybe someone elses life. If any of thise things failed and i was going over 20 mph it could have been so SO sad. So seriously. Tysvm. 🥹 my 2008 toyta rav 4 is sitting in my deiveway unable to move not because of the engine or transmission or differential but because there is soething else wrong and tomorrow im tearing into it. This is the first thing im going to check.

@Naval-Gazing-Society 2 ай бұрын

thanks! very helpful!

@danielguerra626 2 жыл бұрын

Can you do a video on diagnosing inner tire wear on front tires?

@josephbarrerareyes 7 ай бұрын

Gracias por compartir.

@trusso11783 Жыл бұрын

I changed my brakes and rotors last October. By Feb, my left rear brakes were down to metal. I looked at caliper but the guides moved fine. I even put more grease in to make sure. Now, I smell a string smell from that same brake. Could it be something else or does it sound like it could be the caliper.

@showgirlsaroundtheworldada4484 10 ай бұрын

Great vlog

@reeeek2017 2 жыл бұрын

Thanks

@jaimecamacho653 2 жыл бұрын

Thanks Sr . appreciate.

@VinodKumar-jt3og 2 жыл бұрын

Yes sir good job 👍

@nashjarwa4347 10 ай бұрын

thanks

@ibogasacramentaljames5190 2 жыл бұрын

a question please.the transfer case of a 2008 rav4 have 2 key nuts. the bottom which is the drain and the next to it ontop the fill. what is the other nut ontop of it for?please help answer

@cynthiapatterson9454 Жыл бұрын

Do you know what would cause the brake area to start smoking after I put on my factory donut? Drove 2 miles about 45mph. After I got the new tire on, it didn't have anymore issues. I've used this same donut before without issue.

@HypocriticYT 2 жыл бұрын

It’s usually a small animal stinking up caught in the mechanism. The large ones roll over the hood.

@linozamarripa1708 2 жыл бұрын

nice video i have at 2005 gmc canyon my brakes where smokey get hot, buerned out the calipers boot, replaced calipers left and right front, new disck to and still getting hot any help, thanks

@alexsimion7190 4 ай бұрын

I did this to my car, the piston retracted quite easily, the pins were looking bad but I cleaned it and lubed it and it looked like everything it's ok and the wheel was spinning just fine when it was lifted but still, after the test drive it started again spinning a bit less than before the test and still gets hotter than the other wheel. What else could it be? I checked the wheel bearing of movement but it seems fine.

@dwightlee6164 2 жыл бұрын

yes.. The torch works.. my sliding pin was stuck completely.. and the torch worked to get it out.

@robertmacgirvin7425 2 жыл бұрын

Another item to look at is your flex/rubber brake lines. I had an issue with my 2012 F-160 4FX. Replaced caliper and rotors and about 10 minuets smoke and a lot of heat. Replaced front hub. Still, smoke and heat. It turns out, the brake hose was collapsing and not letting the fluid leave the caliper. $ 20 buck part, replace it, I did not, my fault.

@cognac8297 Жыл бұрын

You that flex line on the master cylinder too

@user-wm4bo4nj8l 10 ай бұрын

hello and hi could u please tell me what is the torque spec on all the bolts from caliper slier pins to the brackets bolts front and rear brakes on a honda hrv 2020 thanks

@alirazmjou2149 2 жыл бұрын

Thank you so much for this video متشکرم

@onpsxmember Жыл бұрын

Try a foam ear plug instead of the glove balloon.

@peaceblessingsall3889 2 жыл бұрын

I got a question for you what if it is leaking brake fluid from the wheel and some how the brake pad came off do I change the the whole caliper bracket to

@markholyoak9790 2 жыл бұрын

you could put a pipe pushed on the brake pedal and seat that would stop the brake fluid from coming out

@paulmetheny2126 2 жыл бұрын

P.S. how about video for replacing unibelt on Chevy Equinox vehicle's

@ngzcaz 8 ай бұрын

Yeah, when you heat a bracket that's it's red hot, it's time to change it, especially since the slider pins still weren't as free as they should have been even after wire wheel and grease. 👍

@junryanduqueza8521 9 ай бұрын

Sir. Can i ask if the caliper sliding pin has a different size?

@MrCoursair77 11 ай бұрын

Great!

@crystalcoleman8668 Жыл бұрын

Do you need to do both sides ? Or can you just do the bad side??

@sarahguin6277 2 жыл бұрын

I have a 2004 jeep liberty v6. I stopped my vehicle an tried to put it in 4wd. And I forgot to put it in neutral. I kept the brake peddle on and then quickly put the shifter back. After that I had little burning smell from vents. Did I do any damage? I just bought it. I'm really hoping I didn't.

@timothymetzler7715 2 жыл бұрын

Hello I see this is a liberty I have a 2004 and before we pull out of our parking spot if you turn the wheel there is a clunking or banging noise in the front end after driving a bit it stops making a noise . Any ideas ?

@andyridley2236 25 күн бұрын

If you push the brake peddle down to the floor and use a piece of wood and wedge it between the seat and the peddle keeping the brake peddle to the floor this will stop the brake fluid from running out

@gordonmeadows2150 2 жыл бұрын

I need help to find the turn signal fuse on a 2012 chevey malibu ls. I looked all over the car and all 3 fuse boxes and I can not find it can you help me out please.

@pamelacowgill9436 Ай бұрын

I have a 2011 Volvo S40 T5. I have replaced the ABS Modulator and pump, the Master cylinder, The right front caliper and rotor and new brakes pads on the front and just yesterday the Flex hose on the right and My bake on the right is STILL locking up on me after it get heated up from driving, I am at my whit's end with what could possibly be wrong with this, I have been dealing with this issue since last year and now I am still going through this, I have had had it through two different shops and had these things done and I just don't know what to do anymore, can you please help me out here and share with me what you think it could possibly be??

@robertehlers4330 Ай бұрын

Hey Andy got a stripped bleeder screw how to get it out

@terabali7247 Жыл бұрын

Good 1

@connorscustoms2628 2 жыл бұрын

Hey why did didnt u geasres the pins

@karlmcnamee7620 11 ай бұрын

My 04 liberty just replaced front brakes and calibers all hoses replaced about a year ago seams all brakes get hot any help

@Arenhammer 10 ай бұрын

Can anyone recommend a great brake repair place south Florida?

@jamesblake365 6 ай бұрын

What if you have slider pins that come with no boots begin with or no combination for the boots

@jjspatel 2 ай бұрын

I have a question, My right front rotor when installing new rotor, by mistake the brake hose got twisted, after driving 5-7 miles, I noticed smoke, so I opened up and saw that the hose is twisted. Made this right, but now I measured temperature after driving 20-30 miles and left rotor is about 60 degrees Celcius and right rotor is around 75 degrees Celcius, is this normal to see temp diff. between left and right rotors or this is because the brake hose was twisted?

@briangarcia1218 2 жыл бұрын

Excelent

@HardyManful Жыл бұрын

It's dangerous to run a double pad system with only one pad in a position right?

@johndeloach503 Жыл бұрын

My brakes as a little squeal and i replaced pads and after awhile it started again. What could be the problem?

@jameswatts9814 Жыл бұрын

Is it normal for new brakes to smoke a little?

@Ytownick734 Жыл бұрын

My Front right tire starts smoking after 10mins, it starts to feel like its dragging then after that it accelerate to 45mph slowly for about a min then allows me to go 60. After i let go of the gas it slows down fast.

@Rickxx881 2 жыл бұрын

How did you not notice that before you put it together.

@rodneyjohnson2064 18 күн бұрын

I hear noise but i can't tell what It is brakes are new rotors are new?

@BagHouseARK 10 ай бұрын

I did a job on a 2006 dodge charger I replace pads and rotors now they are smoking hot. So no I need to boot and pins since they stuck needing help asap

@jamieatchison3731 Жыл бұрын

I replaced everything to brand new and it is still heating to the point it is smoking. What could the problem be?

@dominicfong6341 Жыл бұрын

Something doesn't makes sense here. Why the rotor look literally fresh-out-of-the-box new and yet it is coupled to a seized up rotor?

@edwinbab705 7 ай бұрын

On prius the rotor bolts very hard to take them out

@sudinebabz8651 2 жыл бұрын

Super 👍🏽

@shahbasharat 5 ай бұрын

Doesn’t heating change the quality of the metal? Especially heating to red hot temperatures. It’s going to weaken the metal

@crossbow3539 9 ай бұрын

Shouldn’t you have crimped the rubber break line hose before breaking the line lose?

@Jayzc66 Жыл бұрын

My rear wheel is whistling😙😚😙 and kinda hard to move just a bit.

@connorscustoms2628 2 жыл бұрын

Rotors still have a cross hatch pattenern doesn't make sense if ha

@druegillette2602 7 ай бұрын

Got my pin out with an adjustable wrench and a lot of heavy whacks with a hammer 🤣

@galaxykicks6880 Ай бұрын

I had just bought new one put it together and it seized up

@alfredflores4017 2 жыл бұрын

I think that pin looked pretty crooked. I seen a slight curve.

@alecjansen4416 Жыл бұрын

Safe to say when using torch you dont need cutting goggle. A pair of safety glasses will do just fine.

@silentraven37 8 ай бұрын

I replaced my entire caliper, pads and rotor, but my tire is still getting super hot and smells like burning. What else may be wrong??

@1AAuto 8 ай бұрын

+Trail Mix We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c