How to Make MINI Air Conditioners | REALISTIC Resin 3D Printed Details for Dioramas

Рет қаралды 13,509

Күн бұрын

Check out how to make miniature air conditioners for your dioramas, displays, and wargaming terrain! I show you how to prep and paint your 3D prints, as well as apply decals and weathering effects to them!
Join My PATREON for Exclusive Content, Including These 3D Models: / smolworldworkshop
Enjoying my content? Want to see more videos like these? Be sure to SUBSCRIBE to my Channel and tap the Bell Icon to get notified each time I post a new video!
Chapters:
0:00 Intro
0:30 3D Models
0:59 3D Print Support Removal
2:09 Paint Preparation
3:20 Priming and Painting
4:27 Assembly
5:05 Applying Waterslide Decals
6:44 Weathering Intro
7:06 Light Weathering (Washes)
7:50 Heavy Weathering (Oil Paints)
9:29 Adding Chipping & Rust
11:11 Final Result!
12:06 Bloopers
Song: Alone Tonight
Music by: CreatorMix.com
Song: Ocean Drive
Music by: CreatorMix.com
Song: Southbound
Music by: CreatorMix.com
Song: Moving On
Music by: CreatorMix.com
Song: New Arcade
Music by: CreatorMix.com

Пікірлер: 44

@marinamarioni6384 6 ай бұрын

It's so refreshing to see you actually slide the decal off the backing paper. I see so many videos where they leave the paper in the water bath and fight the wrinkling folding decal over the the object, then have to wrestle it in place. They are called water SLIDE decals because you sliiiiide the decal off onto the object!!

@yasirbhojani Жыл бұрын

Damn! The rusty one is incredible! Hard to believe this is a scale model. Thanks for sharing!

@smolworldworkshop Жыл бұрын

Thank you so much!!

@badbassnine 2 ай бұрын

I really wanna get into miniature building stuff

@smolworldworkshop 2 ай бұрын

I think you should! Making miniatures is a lot of fun!

@alexandre.studio3d Жыл бұрын

Great job. I also love to 3d print accessories and tools for my dioramas.

@smolworldworkshop Жыл бұрын

Thank you! 3D printing has been a great addition for this hobby!

@cherylwatts2739 Жыл бұрын

Awesome job painting!! So informative.

@smolworldworkshop Жыл бұрын

Thank you!!!

@user-wl5ld6qe7u 4 ай бұрын

i like the panasonic and daikin one

@smolworldworkshop 4 ай бұрын

Thank you!

@randybourque3327 11 ай бұрын

Try soaking your 3D prints in some hot tap water for a few minutes and they seperate your parts from the supports with out having to use a knife, it is a lot safer and easier. Use nippers to cut away the integrial supports that might otherwise break the print. You are very talented Blessing Pastor Randy Bourque

@smolworldworkshop 11 ай бұрын

Thank you again for all your help!!

@drowsy4400 6 ай бұрын

Would be cool to fit a small fan and a 9v battery inside

@smolworldworkshop 6 ай бұрын

That would be awesome!!

@HowtoMakeThings 10 ай бұрын

So how about making the indoor units? They could be used in future diaramas

@smolworldworkshop 10 ай бұрын

Good idea!! Not sure when I’ll get around to making those, but I’m sure I will at some point! Thanks :)

@HandcraftedWorlds 10 ай бұрын

Love how they turned out! I just had a question. You always remove the supports with an knife I do the same but to you remove them before or after curing your print? And what resin do you use? What I use seems to be a bit harder and less flexible than yours so damages quickly when removing supports.

@smolworldworkshop 10 ай бұрын

Hi there, thank you!!! I typically remove them before post curing the print which is why the prints seem kind of flexible. Also because the prints are so thin, that might have something to do with it too Also I use Elegoo Standard Grey Resin for my Elegoo Saturn S. Hope this helps!

@HandcraftedWorlds 10 ай бұрын

@@smolworldworkshop Thankyou!

@adamstein5773 Ай бұрын

Would you consider selling any of your 3 D prints outright?

@beltex63 10 ай бұрын

Why not use a clear decal and print the rust or dirt and apply decals?

@smolworldworkshop 10 ай бұрын

You could do that! I personally prefer to use as little decals as possible though, I enjoy weathering and painting with brushes. Thanks for watching :)

@DaveSCHS 9 ай бұрын

Looks fantastic. 1/24?

@smolworldworkshop 9 ай бұрын

Thank you! Yes, these are 1/24 scale

@jakecalrow 11 ай бұрын

Amazing work mate. What printer did you use for this job? Cheers

@smolworldworkshop 11 ай бұрын

Thank you!!! I used both an elegoo Mars pro (the first one) and an elegoo Saturn S. I hope this helps!

@jakecalrow 11 ай бұрын

Nice! Does it matter what printer you have? Could you just use one of the printers for this process?

@smolworldworkshop 11 ай бұрын

@@jakecalrow yes you only need one of the printers! Both do a great job, and honestly I think most if not all resin printers would work!

@jakecalrow 11 ай бұрын

Ah awesome, and I would need a resin printer for miniatures right? Thanks for your help btw. Can’t wait for more uploads.

@smolworldworkshop 11 ай бұрын

@@jakecalrow Yes, resin printers are very good at capturing fine miniature details, so I'd definitely recommend them! Of course, and thank you so much, I'll have some more videos out shortly!

@DOTTYTIME Жыл бұрын

What brand of 3d printer do you suggest

@smolworldworkshop Жыл бұрын

Hello! I currently have an Elegoo Mars Pro and and Elegoo Saturn S. My Elegoo Mars Pro has printed well for me for two years now and was a great beginner printer when I was getting started. I hope this helps!

@DOTTYTIME Жыл бұрын

@@smolworldworkshop thankyou