SUPER SIMPLE PROPANE FORGE BURNER!

SUPER SIMPLE PROPANE FORGE BURNER! - ELEMENTALMAKER

Рет қаралды 1,155,273

6 жыл бұрын

CLICK DESCRIPTION FOR PARTS LIST
Lets build a propane forge burner out of simple parts from the local big box store! This burner will be used in an upcoming video to melt a ton of aluminum cans, and to make Magnalium!
Parts list:
20PSI Propane Regulator - Here is the one I bought: amzn.to/2fsPgsn
Here's a cheap numbered drill bit set. I used a #53 but you may need to adjust slightly for your specific setup: amzn.to/2PqoN16
1/4" Ball Valve: amzn.to/2UgOdTI
3/8" FL x 1/4 MIP union (to adapt regulator output to 1/4"): amzn.to/2UfaxNx
1/4" Coupling: amzn.to/2UrxBJa
1 1/4" to 3/4" Reducer: amzn.to/3qk3gIu
1" to 3/4" reducer: amzn.to/3xE3EDP
8" section of 3/4" threaded pipe: amzn.to/3d38Mtz
1/4" x 2" nipple: amzn.to/3iYHE2D
1/4" square head plug: amzn.to/3qguI9L
Two 1/4" hose barbs: amzn.to/3xE3egJ
1/4" ID vinyl tubing (if you want to run your burner further away from your tank): amzn.to/3djxTZl
The above links are affiliate links which give the channel a small kickback to help fund projects.

Пікірлер: 1 100

@ElementalMaker 6 жыл бұрын

Hope you guys enjoyed! It would a HUGE HELP to the channel if you save this link as your amazon homepage, so when you shop the channel gets a small kickback: goo.gl/x1ehvA Please consider helping to keep these videos coming. *Parts List Below* : Parts list: 20PSI Propane Regulator - Here is the one I bought: amzn.to/2fsPgsn Here's a cheap numbered drill bit set. I used a #53 but you may need to adjust slightly for your specific setup: amzn.to/2PqoN16 1/4" Ball Valve: amzn.to/2UgOdTI 3/8" FL x 1/4 MIP union (to adapt regulator output to 1/4"): amzn.to/2UfaxNx 1/4" Coupling: amzn.to/2UrxBJa 1 1/4" to 3/4" Reducer: amzn.to/3qk3gIu 1" to 3/4" reducer: amzn.to/3xE3EDP 8" section of 3/4" threaded pipe: amzn.to/3d38Mtz 1/4" x 2" nipple: amzn.to/3iYHE2D 1/4" square head plug: amzn.to/3qguI9L Two 1/4" hose barbs: amzn.to/3xE3egJ 1/4" ID vinyl tubing (if you want to run your burner further away from your tank): amzn.to/3djxTZl

@_AZAZEL_ 4 жыл бұрын

Jeff Bezos is smaug dont give him your business.

@troysimon9933 3 жыл бұрын

What modifications would be neccesary, in order to make this design into a "forced air" burner???

@manuelmendonca8482 3 жыл бұрын

@@troysimon9933 with this system you don't need forced air. My furnace melts , Aluminium , Brass , bronze, steel the whole furnace turns white inside. One more thing forced air erodes your crucibles faster.

@harrisoncrane360 2 жыл бұрын

Would it work to drill the nozzle with a 1/16 of an inch bit

@julioc3845 4 жыл бұрын

This is the cleanest flame I've seen on burner videos. Great job.

@bugsbunny8691 5 жыл бұрын

My Grandpa taught me that the three holes in the drill chuck weren't there for convenience and that they were all three supposed to be used when tightening down on the drill bit. After that Drill bits didn't spin nearly as much. great video as always..

@d.faulkner8210 5 жыл бұрын

would not recomend using plastic tubing for a propane supply line,invest in a high pressure hose meant for propane,would be ugly if that plastic tubing melted from the heat while using that burner.nice burner design ,be safe..

@JustinTopp 4 жыл бұрын

I’ve heard that but it never had made a difference in my experience

@rufuscrackle 4 жыл бұрын

Heard that once in the 15 machine shops I worked at. Don't believe it and only that one guy out of a 100 did it.

@-yeme- 4 жыл бұрын

dont see it myself, all three tightening points are turning the exact same part in the chuck. could it make a difference where on that part you apply the turning force? idk. could be that just by taking the key out, putting it back in and tightening again youre making sure the tool is snug in the chuck, whether you use the same hole or a different one

@joeestes8114 4 жыл бұрын

Bugs Bunny thank you! I was going to comment the same thing!

@rikkimaru7705 2 жыл бұрын

I don't know why I waste so much time watching several videos made by several jokers before I end up watching yours. Someday I'll get smart and start at the finish. Your da man

@ElementalMaker 2 жыл бұрын

Thanks for the kind words Rikki

@carstenm 3 жыл бұрын

This content is so good, been binge watching @ElementalMaker for the past week!

@thomaswilliams3982 5 жыл бұрын

I really appreciate the content, super informative. I'm new to forging/blacksmithing. I'm going to give this a try. The one thing I wish you would have clarified is the process of the propane end of the burner. I'm kinda lost on the configuration. Thanks again man.

@andysalagaj1476 4 жыл бұрын

I loved this video - Thanks for the info. I used your plan for making a forge burner but had to use a 30 psi propane regulator to make it work. I live at 8500 ft elevation so I assume thats why. Again thanks!

@KusaKorat123 5 жыл бұрын

Very nice video Mate. Thanks for that. One of the Best Step by Step descriptions right here. The burner System is very good and Works like you said

@johnkennedyswenja 4 жыл бұрын

I appreciate you, you were so straight forward even I can make one, off to the hardware store.

@wavydave 2 жыл бұрын

I guess this is a popular and much used design. I've seen dozens of videos through the years that are all almost identical starting with TKOR back in 2016. Great video with everything explained step by step, just like your other videos. As long as you keep making these cool build videos I'll keep watching and sharing.

@ElementalMaker 2 жыл бұрын

Thank you. Yes this is called a Reil burner. Very popular style coined after the man who designed them originally

@billy19461 4 жыл бұрын

Loved the video! I have made several torches to pre-heat pipe before welding and I always just took an grease zerk and filed the end off, then removed the ball and spring.

@johngaudi8546 4 жыл бұрын

Do what? I can't picture which kind of grease fitting?

@tomt9543 3 жыл бұрын

John Gaudi A zerk is a standard grease fitting! Kind of like the proper name for the thing you inflate car tires through is a Schrader Valve! I love to call it a Schrader valve in general conversation because it gives the false impression that I know much about everything! Ha!

@gordonfischer8484 3 жыл бұрын

Thanks for making, this is the best and easiest design I could find. Definitely going to make this.

@paris466 4 жыл бұрын

Well, I started my foundry build and of all the burner designs I looked at, yours is the one I went with. Fired it up and it works fantastic. Now I just need to finish building the foundry itself and I'm all good to go. Thanks

@ElementalMaker 4 жыл бұрын

Nice! Glad it was useful for you!

@derekbryant6137 4 жыл бұрын

I actually learned something thank you for the information most informative

@petermartin9478 5 жыл бұрын

I built this in no time . Put a 30 lb. Reg on it . Works like a charm. Thanks ! This will go into a propane tank forge. Just a note ... doesn't seem to need but 10 lbs of pressure , at least for mine .

@adamgravelin3002 2 жыл бұрын

So I made this exact burner, and tried to use it in my propane tank forge but it just seems like it wants more air. Can't seem to figure out how to get it more air either.

@timkohn7770 2 жыл бұрын

I am watching your video for the last time before I go to buy the parts. I am excited and your instruction is easy to follow and I can't wait for MY results....thanks again....Great stuff here

@anthonyleggio4877 3 жыл бұрын

I made this following your instructions but used a 1/2 cap, 1.5 inch to 1 inch reducer coupling, 1 inch pipe and a 1.5mm hole for the orifice with a 10 pound regulator and it worked very well! Thank you for your contributions to the DIY community! I was just about to give up on making my own burner after my old one with the same regulator failed to produce a blue flame. I think my problem was the amount of airflow in the old system that reused a burner from a furnace with a 1" coupling welded on. I still ordered the new regulator because I want to see how hot I can make it but overall a wild success! Thank you again!

@jaywethington1934 3 жыл бұрын

I've watched a bunch of these videos and I found that yours was easiest. Definitely be using your design for a double burner. - the galvanized tip. Im not very fond of getting poisoned

@tikitavi7120 3 жыл бұрын

Yep, that galvy has got to go.

@lx2077bob26 3 жыл бұрын

Just dip it in muratic acid and in seconds the coating is GONE

@Nubby007 2 жыл бұрын

@@lx2077bob26 or just leave it on vinegar overnight, lots cheaper

@oak_meadow9533 3 жыл бұрын

As a mathematician I can tell you that drilling your set screw holes 120 degrees apart would have allowed redirection of the flame down the center line of the burner very to be exceptionally simple.I admire your desire to always use the most efficient methodology for your diy build projects. I always enjoy watching a talented experimentalist in his element. You are like seeing Michael Faraday reborn; without him there would not have been an Edison or Einstein, or a Niagara power station humming with Nicolai Tesla's AC alternators..... Mr. Elemental for a while I thought that you might have been an alchemist like Isaac Newton, but there is no turning lead to gold, alas..... In the meantime carry on with the brilliant production of video material. Bye from Central Texas, USA.

@andrewroberts3187 2 жыл бұрын

That would work, but you would need a very long drill bit and have to line it up on both sides. The way he did it lowers the tolerances.

@richvandiverdds4311 2 жыл бұрын

I’ve watched at least 15 of these on how to make a burner, and I think this one has been the most simplest and comprehensive covering all the unknowns. So after months of trying to decide on the right burner today I started buying the parts, though I AM curious why so many people use the welding tips drilled out yet this one works just fine with a quarter inch plug drilled out with a “60k bit” Which by the way seems to be about 2.65 mm. Hard to find locally but Amazon did have it for about eight dollars in tungsten. Thanks for making it sensible and doable. The flame seems to look right for the square forge I’ll soon weld up. I hope the lack of a Venturi doesn’t impair.

@seanwilson9219 4 жыл бұрын

Dude what a great video beat I've seen, your the man! I appreciate the knowledge. Thanks

@tomstegner1294 5 жыл бұрын

Hey man, just want to thank you for this video. I have never done anything like this before but I followed your instructions and...OH MY!!! My initial test was incredible. No need to change anything, working just like you said. Sounds like a hot air balloon and my neighbours are getting nervous. lol. THANKS MAN!!!

@ElementalMaker 5 жыл бұрын

Glad to hear it Tom 👍 stay safe and enjoy!

@conquerant8804 4 жыл бұрын

what size bit did you use

@wezerd 2 жыл бұрын

@@conquerant8804 30 thou

@KendrasEdge757 6 жыл бұрын

Minute 8:07 YEAH! SHAMELESS KY PLUG!! LOVEIT!

@ElementalMaker 6 жыл бұрын

Si Vis Pacem Para Bellum KY and plugs usually go together in another way butt I'm not quite sure how to break it to you.

@KendrasEdge757 6 жыл бұрын

ElementalMaker that’s cool, I’m not judging you, you’re into what you’re into. You don’t need to explain it to me!

@richardrounce7138 Жыл бұрын

Made one the other day, used a number 54 drill bit. With a 20psi regulator it rips. Flame is about 12" long and hot as hell. Thanks for the video and parts list, cheers 🍻

@boriskarloff598 2 жыл бұрын

I'm going to build mine just like this. No mig tip, no threaded damper, just wide open using a 1/16th jet orfice. Great work!

@R1ceau 4 жыл бұрын

Hey, great video!. I'm just wondering how hot this burner is able to get. Cheers.

@michaelvilloria5032 4 жыл бұрын

i ain't livin' yet bro... need that gold plated Allen wrench in my life

@danielmaciej5764 5 жыл бұрын

I built this exactly like he showed on the video. It works great! This bad boy puts out A LOT of heat!! Now I just need to make the forge to put it in. Thanks for the great video!

@ElementalMaker 5 жыл бұрын

Awesome! Glad its working great for you Daniel!

@rubencardoso635 5 жыл бұрын

Excellent video, great project. Thanks so much, I will definitely do it.

@ElementalMaker 5 жыл бұрын

Glad you enjoyed Ruben 👍

@jmcbc1963 6 жыл бұрын

Nice video with the exception your internal flare needs to be black pipe and NOT galvanized. Zinc poisoning can kill you. The galvanized coupler on the back doesn't matter it's not directly exposed to the flame. I know you said you'd probably only use it outside but still, many who watch this wouldn't/don't know that. Stay safe everyone, and be informed.

@ElementalMaker 6 жыл бұрын

Very good point Jay. If KZfaq still would allow annotations I would make note of that in the video.

@AmericanPiddler 6 жыл бұрын

Jay Cee good sound advice! Care to check mine out? kzfaq.info/get/bejne/qp9_n7V5p87DhKs.html

@ytSaipan 6 жыл бұрын

The amount of zing on the flare will not kill you. As a precaution set it in a wood fire outside for about 20 minutes and the zinc will burn off.

@wonhuanglowsoverylow5000 6 жыл бұрын

Lmao. After the first burn the tiny quantity of zinc will burn off. The threat of zinc poisioning is insignificant compared to the fumes that will come from what is being melted or heated lol

@unmanaged 6 жыл бұрын

en.wikipedia.org/wiki/Metal_fume_fever#Treatment I would not be worried about such a small amount ....

@henryhamilton9574 5 жыл бұрын

Love the design (it should be noted that galvanization should not be anywhere near the fire).

@ElementalMaker 5 жыл бұрын

Thanks! And yes zinc and fire generally dont go together. In this case it's all the hardware store had, and it's such an insignificant amount you would need to be huffing it LOL

@lucienkpoikpo9288 5 жыл бұрын

GBEZE

@skeetfontenot4922 4 жыл бұрын

Just soak it in vinegar and then brush off the zinc.

@turninandburnin8798 3 жыл бұрын

I built one from the plans, works great, I have the stuff here to build a second one, hopefully I can get started on it soon!

@charles4958 4 жыл бұрын

So, I didn't have an 8 inches pipe and I didn't have a #53 drill bit...I tried with a 10 inches and 1/16 orifice with a 0-30psi regulator...this is an inferno! I didn't even try full pressure haha. Thanks for the tutorial, I had an idea of a venturi burner, but it required much more work.

@64t120r 6 жыл бұрын

Nice job. I would like to make one suggestion. Use a cordless drill to tap your holes. Generally speaking, people break less taps using a cordless than they do when tapping by hand.

@ElementalMaker 6 жыл бұрын

64t120r thanks for the tip! Oddly enough the only time I've ever broken taps was with a drill LOL. I'm bass akwards though, so that might be why.

@64t120r 6 жыл бұрын

Well . . . go break some. That is funny. I have to say, very good technique then. We get more broken taps when people do it by hand. Either way, I'll have to look through your videos and see what other goodies you have.

@NRDavis-wl8vn 6 жыл бұрын

Try tapping with your Drill Press. Drill hole, remove drill, insert tap. Everything is lined up. Turn and feed by hand or..... Get Tap Spinning, turn off power and feed down. Use to do it a lot in the machine shop for Quick and Dirty Jobs.

@ElementalMaker 6 жыл бұрын

David Dedrick some day I'll rack up the balls to do some power tapping on my drill press. I do it on my cnc mill, but I know there isn't any flex there, where as my drill press isn't super rigid, despite being "Rigid" brand.

@NRDavis-wl8vn 6 жыл бұрын

But.... Think of making a Video of trying the process. Scrap length of Aluminum and say a 1/4-20 tap. Not really necessary to keep everything locked down super tight. When you drilled out the Brass Plug you let it float a bit. In tapping that "float" is o.k. Just keep downward pressure and with no power you can stop the chuck by hand it you need to. Still have to back it out by hand but much faster than hand tapping both ways. In joy!

@jrhattenstein 4 жыл бұрын

That's how we got metric and SAE sizes in our vehicles "I'll use metric since I have some lying around."

@therealjamespickering 3 жыл бұрын

Oh I know all about that. I used to have a Land Rover and it was anyone's guess what manner of bolt had been used.

@wianbason2984 4 жыл бұрын

so use to seeing the other channels taking a thousand measurements to make sure its center glad to see im not the only one eyeballing things

@mackdaddynutjob 4 жыл бұрын

Best burner flame i have seen out of 10 KZfaq builds.. good work!

@ElementalMaker 4 жыл бұрын

Thanks!

@dooleyknoted5951 3 жыл бұрын

I concur! Plus, it's a better design than most commercial burgers available!

@paris466 4 жыл бұрын

Little bit of motor oil in a squirt can does wonders when drilling... The final build is bad-ass, though. Great work

@suzukiclaus3028 4 жыл бұрын

SparksFly vd40 ;)

@robertidenya1432 4 жыл бұрын

He did say a little KY jelly would do the trick 😊

@japudjuha 3 жыл бұрын

@@robertidenya1432 saving that for the spare nipple ;-)

@robertidenya1432 3 жыл бұрын

@@japudjuha hehehe

@PACstove 4 жыл бұрын

5:17. Thank you for filing correctly.

@HYDROGENTEK 6 жыл бұрын

I've watch multiple design for a forge burner, this is by far the best design. thank you for sharing.

@ElementalMaker 6 жыл бұрын

HYDROGENTEK I appreciate the kind words! Thanks for checking out my channel!

@JACKHAMMER82A1 2 жыл бұрын

Thanks to your video i made this single torch for my foundry and a 2 burner torch for my forge.

@bunyanforgings7849 5 жыл бұрын

I believe "Blueblock" for fitting joints as opposed to teflon tape.

@TheIrishdriven 3 жыл бұрын

Or the yellow tape

@ChozoSR388 5 жыл бұрын

Ah, yes, the German standard of holding force; guten tight

@ElementalMaker 5 жыл бұрын

My favorite standard as well!

@TrojanHorse1959 5 жыл бұрын

I thought that "gutentight" was German for "virgin?"...LOL!

@ChozoSR388 5 жыл бұрын

@@TrojanHorse1959 Ha!

@treygrubbs2550 5 жыл бұрын

What if your guten free? How tight do you get it then?

@Michel251167 3 жыл бұрын

it is not a German word..aim German..

@RGun90 3 жыл бұрын

Now need to do a giant "garage heater" version! Would be awesome to see what you'd come up with

@DIYPhil Жыл бұрын

thanks for the video. been looking at other designs and yours is the one I will go for

@pwrovld 5 жыл бұрын

Very nice burner You have built here. However, you should not use the Teflon tape in the BLUE package, it is for liquid, like water. They make Teflon tape especially for gas pipe with a YELLOW outer ring. Be aware, be safe.

@joshavant4386 5 жыл бұрын

Thats not true at all. You can use blue ptfe tape for gas. No problems. If anything skip over the ptfe tape and use dope.

@sliderdrago8189 5 жыл бұрын

Colour usually determines thickness. Check approvals for your jurisdiction. But as Josh said. Use the dope man. I dont know anyone who uses tape for gas or oil.

@joshavant4386 5 жыл бұрын

@@sliderdrago8189 in my jurisdiction, once the pipe hits a certain size, you use both. I thinks it's after 1 1/2 inch.

@capt.craiglehrke4395 4 жыл бұрын

Seriously folks remember the build is an occasional use forge burner outside or in a shop. I wouldn't worry about what teflon tape to use unless I was hooking up a stove, furnace or water heater in the house.

@JonJon501 3 жыл бұрын

Don't need any of that.. its low pressure!

@TMRYZF 5 жыл бұрын

What the diamètre you dril the square head plug please?

@TMRYZF 5 жыл бұрын

Thank you tributary House Ltd😉

@Bspstroke_ 6 жыл бұрын

Very simple and easily attainable design. Saved me a bunch of time designing and scavenging the parts stores!

@ElementalMaker 6 жыл бұрын

Bs6.0pstroke_ 28 glad it was helpful for you! Thanks for checking out my channel!

@alphazuluz 5 жыл бұрын

Very cool. I just made one like yours but with a 5 psi regulator from a turkey fryer (I’ll get a bigger one, but I had it on hand) and it actually works well. The flame it puts out is about 2/3-3/4 what yours does. It should be enough for my small forge.

@jakemakes 6 жыл бұрын

How hot is this burner? You think it would be sufficient to power a gas forge on its own? (able to reach forge weld temps fairly quickly) A lot of guys use two burners, but I am wondering if it is necessary.

@AmericanPiddler 6 жыл бұрын

Jake Makes mine is hot enough for a forge check it out! kzfaq.info/get/bejne/qp9_n7V5p87DhKs.html

@ArizonaVaporTrails 6 жыл бұрын

You can check lp gas orifice charts on Google for btu and pressure. Run mine at 22psi and get 250000 btu

@AmericanPiddler 6 жыл бұрын

Jc Polston kzfaq.info/get/bejne/qp9_n7V5p87DhKs.html

@peterzingler6221 6 жыл бұрын

Actually these things work good i work AS a Metall builder\Knife maker in a little shop (2 men) and we got those propan torches Mount in diy furnaces made Form gas bootles ! Its more than enough for blacksmiting hardening and melting brass silber copper and so on

@justinpyle3415 6 жыл бұрын

in the correct envireonment, this temp flame can be used to get to welding temp, however the refractory materials and forge shape have to be pretty efficient. i suggest a dual set up of this, by using the 30psi regulator and adding a tee for a second burner, you wont need as long to get steel to welding temp with two, and it could pretty handily liquify the steel in an efficient forge/ foundry

@scottfain3629 6 жыл бұрын

Can use a MIG welder tip instead of drilling-out that tiny hole in that pipe-nipple cap.

@n.b.customtackle2017 6 жыл бұрын

Scott Fain yes

@yesdeere1376 6 жыл бұрын

What size, .025?

@Bspstroke_ 6 жыл бұрын

YesDeere13 .060 would be the same as his. I'm sure .045 would work, you could use a torch tip file set to widen the hole.

@americanrebel413 5 жыл бұрын

COOL! thank you for sharing this. Now I had better get busy in build mine.

@Maine307 4 жыл бұрын

Today .. I make this ! I will let you know how it turns ! Semper Fi from Maine !

@fredwild190 3 жыл бұрын

I have limited experience, but it looks to me that videos like this almost always show the burner burning beautifully in the open air. They rarely show how the burner performs in an enclosed furnace without additional air to support the flame. That is the question. Does the burner draw enough air for a strong and efficient flame in an enclosed furnace?

@DetailingJourney 2 жыл бұрын

It does

@oh8wingman 6 жыл бұрын

That "cheap steel" is in fact ductile iron or malleable cast iron. You can tell by the chips when you are drilling it. Steel will spiral, even with a dull bit. Cast will give a granular chip just like the ones you got. Home Depot doesn't normally carry steel fittings as they cost more and few if any would ever know the difference. A better way to mount your burner gas jet might been to have used a 1 1/4" pipe plug with a hole drilled in the centre big enough for your gas jet to go through. Since the pipe plug has a 4 sided boss cast onto it you just drill and tap one hole to retain your gas nozzle. To get your air flow just drill 4 or 5 suitable holes through the plug around the boss. Much stronger and less likely to fall apart.

@marcandrei8061 5 жыл бұрын

Norman May no one cares smartass

@TheChoncho212 5 жыл бұрын

You can also tell it's cast be the mold marks on the side.

@willchoate7072 5 жыл бұрын

You do know steel can be cast, just because something has casting marks doesn't mean it's not steel. The chips or spirals is accurate.

@armandorodriguez2694 4 жыл бұрын

Woooohhh, de 5 videos que he visto éste es el que más me ha gustado, gracias, nada de flama amarilla

@JasonVladimir 5 жыл бұрын

Good show as always, thanks for sharing!

@chrisvenable5218 4 жыл бұрын

For everyone worried about the galvanized coupler. IT'S BEHIND THE FLAME. therefore it's not burning

@superdave54811 4 жыл бұрын

It is a mistake to hold a object in your fingers/hand when drilling. I have seen so many accidents caused by holding with fingers/hand.

@JustinTopp 4 жыл бұрын

Lana yea I agree. I drilled into my finger by holding it in my hand too close. Had to get stitches wasn’t fun

@timothycasey6877 4 жыл бұрын

He also states never touch a spinning chuck.... Then proceeds to stop a spinning chuck by hand twice...

@Terry-cx3tl 5 жыл бұрын

Will be making this! Thanks for the video

@ElementalMaker 5 жыл бұрын

Your very welcome Terry! Good luck on your build!

@celioyam997 6 жыл бұрын

Nice! Simple and functional

@symalus 5 жыл бұрын

It cuts to commercial right when you're lighting it "And then he died"

@tygs6984 5 жыл бұрын

Almost perfect! If you used a dye on the 2" nipple and extended the threads you could cut a piece of metal drill and tap it to fit those threads and then you will have an air control valve! Or get a nipple with longer threads .

@TheTradesmanChannel 6 жыл бұрын

Good job, building one right now on my channel and this helpful.

@mikegrant8490 4 жыл бұрын

When drilling, tighten your chuck in two places or more... lessen the likelihood of the bit loosening.

@senatorjosephmccarthy2720 4 жыл бұрын

Yep, tighten all three.

@FPChris 4 жыл бұрын

And use cutting oil

@karolciezkiewicz3232 5 жыл бұрын

"So many nipples, unbelievable" :D Great video mate. And not just because the nipples tho.

@liquidwarriors6793 4 жыл бұрын

great job man¡¡¡¡ thanks for sharing this kind of knowledge

@francescozambuto1713 2 жыл бұрын

Having some fun when showing laymen how to make a homemade torch makes it entertaining.. I learned from this, Thank you

@ElementalMaker 2 жыл бұрын

Thank you very much Francesco

@bsunderland13 6 жыл бұрын

You say to not touch a "spinning chuck" but you touch it everytime to stop it!!!

@ElementalMaker 6 жыл бұрын

bob sunderland do way I say not what I do LOL

@seanogr8044 4 жыл бұрын

Do as I say not as I do 😆😆😆😆😆

@manuelmendonca8482 3 жыл бұрын

@@ElementalMaker Old hands or professional always touch the chuck we know what we are doing through years of experience and mistakes.

@jmbstudio6873 6 жыл бұрын

Not bad. Unfortunately you cannot run this type of burner with forced induction. I used a tee and brought my propane into the side of the tee and used a .6mm mig tip for a nozzle. Super efficient and runs way longer on way less gas. No brass needed in my setup either. Everyone copies Majestic or Diamondback forges. Those need about 30 psi of propane to get up to forge welding temperature, mine achieves the same temp at 6 psi. I run mine at 3 psi for forging. Also...as stated, zinc will kill you. BBQ regulators have enough psi....but are low flow regulators and will not work. Get one from Suburban Propane or a Propane supply outfit.

@ElementalMaker 6 жыл бұрын

What are you using to provide the forced induction?

@jmbstudio6873 6 жыл бұрын

This little blower motor works great! www.zoro.com/dayton-blower-75-cfm-115v-045a-3016-rpm-1tdp3/i/G2510164/feature-product?KW2&gclid=EAIaIQobChMI18a3qIbQ1wIVlddkCh3AlwXwEAAYAyAAEgKU1_D_BwE&gclsrc=aw.ds

@jmbstudio6873 6 жыл бұрын

This is the burner I made. facebook.com/media/set/?set=a.1794002967556385.1073741831.1692028454420504&type=1&l=5fb7f4a34f

@jeffbobold 6 жыл бұрын

Studio 68 the FB link you posted isn't working for me. Do you have a video anywhere that shows your set up?

@6969smurfy 5 жыл бұрын

Studio 68 would have link to seen your burner, but I dont do that BS facebook ch!t no more....

@scott-kf1bi 4 жыл бұрын

Awesome build, love it.

@ElementalMaker 4 жыл бұрын

Thanks Scott 👍

@abdel-hadikaddourn2bricola725 10 ай бұрын

Meilleure vidéo , meilleure flamme bleu ,meilleure conception , bravo

@JaakkoF 6 жыл бұрын

Why do you sound like AvE :D

@odczynnik 6 жыл бұрын

I thought for a second that I play AVE vid:D

@milos_radovanovic 4 жыл бұрын

I didn't believe it wasn't him until I tried pitch correction and couldn't get a perfect voice mach.

@elalguazil 5 жыл бұрын

That is a kick ass video Mister 👍🏽

@SandroSGeraldo 6 жыл бұрын

Really cool. It's look like so easy to build and works so good.

@ElementalMaker 6 жыл бұрын

Sandro S. Geraldo it is a very easy build and works great! Thanks for checking out my channel!

@contrerasSAM 4 жыл бұрын

hehehehehehe he said "nipple" hehehehehehehe

@hypothalamusjellolap8177 4 жыл бұрын

It seems K Y gelly is the ticket.

@mattcerbone4313 6 жыл бұрын

Watching you work is painful.

@atrumblood 5 жыл бұрын

We've been spoiled by watching AvE and This Old Tony. Lol

@WayneEarls 5 жыл бұрын

Machinist nightmare. but it worked.

@monkeyship74401 5 жыл бұрын

Probably painful for him too...

@rudawgs5418 5 жыл бұрын

Haha.....someone is gonna be miss digits soon...and NO I don't know how to make sandwiches...haha

@nathanbalaich9110 3 жыл бұрын

Nice video, will by using this for my build. Only thing is to be careful with galvanized steel used in heating components. Those parts shouldn't get too hot here, but if they do they can release toxic fumes. Best to de-galvanize first just to be safe.

@bunyanforgings7849 5 жыл бұрын

I just test fired my burner based on your design last night. Worked perfectly. Now I can start building my gas forge. I made two changes, however. First was to the end cap. I drilled and tapped it to take a mig tip. The other was to the squared coupler. I used the drill press to put four dinples in where the screws that hold the burner tip assembly can seat themselves. My thinking was that this way I don't have to over tighten in order to prevent the assembly from shifting. Regardless, greatly appreciate you taking the time to research and make a video on the subject. Stay safe. Cheers.

@beshkodiak 5 жыл бұрын

Axel Heinz i like that four dimple idea to hold the gas input. I have used a coal forge for 30 years but now that i live in the woods, propane is easier to get than coal so I am building a new propane forge.

@bunyanforgings7849 5 жыл бұрын

@@beshkodiak My new problem is setting up an efficient ventilation system. On my second test of the forge I set off the CO detector and then the wife (that was scarier). Hope to be using the forge soon. Good luck, Besh.

@ronniejeffvanderboegh4359 5 жыл бұрын

I have found that when drilling soft metals it is much better to grind the cutting surface of the bit to a - 5 to 10 degree angle as to the face you will avoid the catching or grabbing effect at the end of your drill as it punches through. What is happening is as you go through the end of your cut the face angle vs the cut angle are too inclined and the softer metals tend to let the drill dig in too quickly. If you reduce the angle of attack it will not tend to pull in as the surface begins to punch through the last portion of your cut therefore reducing the likelihood of your tool ceasing at the end of the punch. Good vid and thanks for filling me in on the foundry. keep it up.

@randychubey5457 3 жыл бұрын

Good instructions, as a long time machinist I recommend Wiha Allen wrenches, but , Bondhus are a decent 2nd to them.

@thomasgallaspie9040 4 жыл бұрын

That's what I needed to see. Thanks

@phaitoon8183 4 жыл бұрын

I really like it. The work is great.

@brookswerner9975 3 жыл бұрын

Thanks so much. I now have a full functioning forge and burner

@ElementalMaker 3 жыл бұрын

Awesome! 👍

@blackfordoblique1965 2 жыл бұрын

00:12 Awesome! Man that was quick too! I'm gettin' one!

@lemix69 3 жыл бұрын

Wow, that was pretty simple, wish I would have watched this last night, could've saved me some cabbage. 🖖😎⚒

@suzukiclaus3028 4 жыл бұрын

Just made it my self works like a champ

@frisaregood 6 жыл бұрын

Maaan, I keep running into your channel. Love the content, keep up the great work!!

@ElementalMaker 6 жыл бұрын

BCox thank you! Glad you like it!

@frisaregood 4 жыл бұрын

@@ElementalMaker 1 year later, I am going to finally build this today! I'll let you know how it goes! :)

@ElementalMaker 4 жыл бұрын

@@frisaregood awesome! Let me know how it goes!

@frisaregood 4 жыл бұрын

@@ElementalMaker Worked like a charm!! Took me awhile because I was building a small foundry at the same time, but this burner functioned great. I was able to work some rebar into a knife while casting some aluminum at the same time! Also, the flare at the business end of her had me a little concerned, so I have it soaking in vinegar because its galvanized and I assume it can't healthy to burn with. :) Many thanks for posting this design. Is it normal for your propane tank to sweat and loose PSI?

@jureloar 4 жыл бұрын

Excelente video, muy claro Muchas gracias, saludo desde Colombia a

@thepolygoners7165 Жыл бұрын

thanks so much, great video

@axemanmike4390 4 жыл бұрын

Great build, EASY to follow instructions! LOVE THE VID, love the humor! Always been interested in black/bladesmithing...just bought first anvil (Hay Budden) 160 pounder! Gotta start somewhere! Now the forge and burner! This vid is perfect, THANK YOU! Greetings from Salem, Oregon! Keep up the GREAT work! SUBBED! 👍👍

@ElementalMaker 4 жыл бұрын

Thank you!

@mystbourne3432 3 жыл бұрын

That’s a hell of a place to start. Good find.

@timothyhackett7372 2 жыл бұрын

i made one with random 2inch stainless tube I had lying around from customers car exhausts and some air fittings I had. cant say it burns as cleanly as yours but it certainly puts out some heat. i also soldered a 0.8mm mig welding tip into the barb fitting for the nozzle seems to work the best

@jeffmarstaeller6540 6 жыл бұрын

Just finished making a modified version of this. Instead of buying the regulator and other propane fittings, i bought a $35 basic weed burner and cut the flare off the end. Comes with a 10 foot hose, dial valve and squeeze control. Just file the edges and slightly enlarge the tip hole for better flow. Great video tho!

@msp3298 4 жыл бұрын

Great video! just started building one today, I hope it works

@pashaveres4629 3 жыл бұрын

a year later... did it work??

@sinisteredgecustomknives7087 5 жыл бұрын

Thanks for the advice. I’ll take a look.

@markscarberry531 4 жыл бұрын

Very nice

@hannable3871 5 жыл бұрын

Great video I've watched a few videos now on this subject. They all have made it so complicated. Yours however right to the point and easy to follow. So thanks.

@ElementalMaker 5 жыл бұрын

Thanks Chris! Glad you found it informative!