Making a Propane Burner even Hotter

No video

Making a Propane Burner even Hotter

Рет қаралды 301,377

7 жыл бұрын

Want to learn sand casting using your 3D printer? I can teach you!: paulsmakeracad...
Previously, I build an easy to make, simple propane burner. It worked, but not great. Today, i'm making it great. Not only do I modify it a bit so i can adjust the air/fuel ratio, but i do something stupid and duck tape a hair dryer to it. Why? because more fire. That's why.
Turns out when you need more air, you can force it down the burner's throat. Who knew. Forced air propane burners are officially awesome. Also scary. But awesome.
The biggest improvement is capping off the back, and making some kind of sleeve to adjust the air hole openings.
Want my advice? I assume you do, since nobody except truly dedicated viewers ever read this far into the comments. My advice is don't do forced air propane burners. Stick with the normal kind. Forced air is just lots of over complication for what I assume isn't an appreciably hotter flame. I love rube goldberg devices as much as the next guy, but the thing is powered by gas. You don't want to plug the thing in, too.
Mailing Address:
1818 Milton Ave STE 100 #1973
Janesville, WI 53545-9998
We have a community Discord server. To join, send me an email at vloggarage@gmail.com, or click here: / discord
Follow me on twitter at / vloggarage
Instagram: / pauls.garage
Patreon: / paulsgarage
Music: "Quirky Dog" by Kevin MacLeod. incompetech.com/
#foundry #forge

Пікірлер: 370

@PaulsGarage Жыл бұрын

Want to learn sand casting using your 3D printer? I can teach you!: paulsmakeracademy.mykajabi.com/joinus

@paulkurilecz4209 Жыл бұрын

You need what is called a flame screen just before the outlet.

@billydamnit 5 жыл бұрын

My wife needs to see this. Finally, proof that overcomplicating something (an under appreciated talent) can be a good thing. "Awesomer".

@noctem9 7 жыл бұрын

Your deadpan humor never gets old. Keep that quality content coming!

@PaulsGarage 7 жыл бұрын

+noctem9 you got it!

@robertlee6409 3 жыл бұрын

I agree, your humor is right on target. I like how you bounce your ideas off the camera, aka the viewers.

@kevindavis3841 4 жыл бұрын

You are a seriously funny man. Only watched about 5 of your videos but I'll watch more. I don't know what your stressful day job is but I'm glad you can overcome ! Thanks for sharing 👍🏻

@allanlarmour7460 6 жыл бұрын

A simple 90 degree bend just after your air intake helps the cas and air mix much better, it will also cause the gas and air to roll. Take a look at how some of the more experienced smiths set up air forced forges and you will see they all have a 90 degree bend on the burners.

@scottripley6381 2 жыл бұрын

I did a similar thing with an air matress inflator to push the temperature high enough to melt copper and brass. My flare was a 1 1/2 inch to 2 inch adapter like yours, however I used a 2 1/2 inch car exhaust coupler with slits cut in one end, hammered in a little to meet the 2 inch black iron adapter, and tack welded on. Makes a great flame holder. Pulls a little extra air in through the slits. It glows red hot when operating.

@Grizzydan 6 жыл бұрын

I built mine off a design I found online.. No holes in the tube, but I have a flapper on the back, along with a quick gate valve on the propane I can dial it in at any temp. Cheers. Love your humor! Subbed!

@PaulsGarage 6 жыл бұрын

Thanks! Glad you enjoy the vids :)

@a0cdhd 7 жыл бұрын

I have heard that inserting a cup shaped piece of fine mesh, the same diameter as the inside diameter of the burner tube, into the end of the burner tube, just before the bell end of the burner will prevent the flame from travelling back down the burner tube. Of course you will need to ignite the burner at the hot end for this to work. If several pieces of mesh are used, the propane / air mix will be evened out and a more effective burn will be achieved. The principle is the same as was used for mesh covered miner's lamps in coal mines around the turn of the century (and probably before that.) As I said, I have never tried this but it sounds like it would work.

@kattasudhir 3 жыл бұрын

mesh covered miners lamp is called davy lamp. sir Humphry Davy discovered sodium, calcium, magnesium, strontium and barium.

@benprenter6886 6 жыл бұрын

Ok. So I've got a burner I've made. Similar design, but no holes. (Venturi style) I was having so many issues melting copper.. it just wouldn't do it. Then I found this video.. I went and took the hair dryer off my charcoal furnace and ta'dad it to my burner. I always hated how loud it was then suddenly it was quiet and my copper... well it's molten! Wooo! Great channel and great advice. Thank you. Keep it up

@PaulsGarage 6 жыл бұрын

Glad I could help!

@gplechuckiii 7 жыл бұрын

LOL, Paul I love the fact that your videos are all about discovery. You aren't teaching you are discovering with your viewers.

@PaulsGarage 7 жыл бұрын

Thanks! The best way to figure out how something works is to dive in and try it! Sometimes you figure it out, sometimes you get huge blue flames. Win-win.

@cliff6532 4 ай бұрын

hey man don't be so hard on yourself you did a good job and you are man enough to correct your own mistakes that's good stuff keep up the good work

@jeffreydauhmer385 7 жыл бұрын

"Why does it keep doing that." There was no question mark at the end of that sentence. You're clearly an intelligent individual. Who, perhaps more clearly, has a lot more theories than answers. Simply put, "I read about propane once, and I have no idea what the hell's going on. But I'm gonna just keep doing shit until it works" I watch your videos because they are so similar to how I figured these things out (exceedingly low budget and nearly no experience with common tools in a regular setting) , and occasionally I derive ideas from your attempts. Like me, you seem to have an attempt to success ratio that is far out balanced. Combined with the incredibly drab rambling, I really enjoy watching your shit. I love it. We're friends now. You understand.

@PaulsGarage 7 жыл бұрын

yep, sounds like we're friends. Crazy people have to stick together!

@Jonathan-jb5gv 7 жыл бұрын

HAHA! Love that you seem to approach these DIY projects a lot like I do. Also love that you're not afraid to share your failures as you iterate toward perfection. Fun stuff to watch!!

@PaulsGarage 7 жыл бұрын

+Jonathan Bechtold if I hid the failures I wouldn't have much of a video left! Everybody has failures. Some people edit them out so they appear to know what they are doing. I think failures are fun to watch, so I leave them in.

@jacobleeson4763 3 жыл бұрын

I know right I did the exact same thing angling the holes with my drill but when I built my first screw up

@Jped277 4 жыл бұрын

Dont light it at the holes! U need to light it at the end where the cone u installed causes a low pressure zone. That's the purpose of the adapter u put on the end

@stevesyncox9893 Жыл бұрын

Ya man, what he said

@HomeDistiller Жыл бұрын

Also the holes aren't really needed, it will draw air from the back of the tube

@jtscustomcutlery317 10 ай бұрын

Oh good I’m not the only one 😂

@shanepetersen2884 Жыл бұрын

thankyou for making this video i just got an old kiln that i swapped over to propane instead of electric and could not get it hot enough to melt copper. i watched the vid made a few adjustments in my set up and boom!!!!!!!!!!!!! now its a forced air unit lol

@PaulsGarage Жыл бұрын

Awesome! You really can't beat forced air. It's a game changer

@mikelaffosse3233 7 жыл бұрын

At first, I was like "who is this fool!" Now I love your sense of humor and enjoy watching. Your like me using videos to make stuff, new subscriber!

@TimeSurfer206 Жыл бұрын

First off, I love your subtitles. Secundus: I have already decided that, when I do make my forge/kiln, I will just do the simple expedient of getting a multiple Propane Manifold, 4 hoses, and the el cheapo Propane Torches, burning 1-4 as needed.

@PaulsGarage Жыл бұрын

thanks! and 4 propane torches sounds pretty intense! I've only ever used 1 and it's plenty

@TimeSurfer206 Жыл бұрын

@@PaulsGarage I'd only have the 4 AVAILABLE, they don't need to all be used every time.

@mattmcdonald6034 6 жыл бұрын

I loved this!!! You're terribly funny. I loved the slight self deprecation being outweighed by the confident optimism in your next great idea💡!!! THANK YOU!!! You made my day!!! 😁

@Jane-xe8lb Ай бұрын

Same😂

@juan-2-many 9 ай бұрын

This man is a genius. Too bad Mary Jane found him first 😂 I’m just messin bro 🙌🏽

@theaudettes2960 2 жыл бұрын

Gas/air best to mix at the nozzle. Try drilling the holes on that bell reducer and orient the location and angle of the holes to come in with a spiraling action. I’m going to work on mine soon.

@HomeBuiltByJeff 7 жыл бұрын

I have been slack and I have just gotten around to watching this. Great content, well explained and executed. Good stuff.

@PaulsGarage 7 жыл бұрын

+Home Built By Jeff thanks! Same to you! I actually got into the foundry stuff hoping to cast some replica/custom car parts, like knobs and handles that are cast, and some engine parts (assuming I can get machining them figured out). The car projects don't start until the toy jeep is done though. Wish I had something like a 911 to work on!

@HomeBuiltByJeff 7 жыл бұрын

Casting is something I haven't played with at all yet, but maybe in the future it could be worth playing with. One of those torches could come in handy on car projects though. I have often needed to heat something up (like with dent removal) and I don't have an Oxy-Acetelene torch. That could do the trick.

@PaulsGarage 7 жыл бұрын

+Home Built By Jeff yeah the propane burner is super handy, I can heat treat stuff, cast stuff, temper/anneal stuff. Propane has a much cooler flame than oxy-acetylene but the flame in mine tends to be much larger, so lower temps but higher heat affected zone. Also my burner will not melt steel no matter what I do, so it's less likely to accidentally burn a hole in something. As a bonus a propane tank is less likely to blow my garage up. Acetylene scares the crap out of me.

@HomeBuiltByJeff 7 жыл бұрын

Being a firefighter, Acetylene scares the crap out of me too ;)

@rk2045 7 жыл бұрын

good demonstration thanks for sharing such basics for floor level operators thanks

@PaulsGarage 7 жыл бұрын

You're welcome! Glad it was helpful

@MAGATRON-DESTROY 2 ай бұрын

You can put a stainless steel mesh at the end to keep the flame from going inside the tube but that might limit gas velocity

@itsclearasmud7718 3 жыл бұрын

I also love reinventing the wheel. Good job.

@darktideryezing 7 жыл бұрын

Paul - Thank you. This was an issue I was currently having with my design and you helped me figure out how to alter it to make it work properly. It's a bit of a different design that uses a welding tip as a propane nozzle (so it could technically be changed out if I needed to alter the AF ratio). The only major downside is that it lacks a cut off valve at the torch, but it has an adjustable regulator with a flow gauge at the tank (and the hose is only 4' so I'm right next to it regardless)

@PaulsGarage 7 жыл бұрын

glad i could help! 4' is a pretty short hose, i'd want a longer one. The shutoff valve being so close like mine isn't a great idea, the heat could potentially screw it up. So far mine is fine, but that doens't mean it will be fine forever.

@ricoloco2803 18 күн бұрын

Put the air intake behind the propane. The air will follow the propane out. With the propane before the holes it mixes as soon as it comes out instead of pulling the are along behind it to combust at the end of the chamber.

@davidj9729 4 жыл бұрын

its the speed of the fuel air mixture.. thats why industrial burners have diffuses.. they dont do it for the cool swirling effect, the flame is always trying to burn back to the nozzle you need the speed to feed more air and fuel into the flame before the flame can outrun the source. the "normal" versions of these types of burners are mechanically tuned the jet of fuel from the orifice creates a vacuum and the cone shaped intake (reducer coupling) facilitates the correct air volume, changing the flow rate through the orifice changing the vacuum and the air volume giving you a mechanically tuned dynamic mixture based on the supply pressure. the flared burner end (reducer coupling) causes the the mixture to slow down and burn in a controlled manor.

@csimeonides 7 жыл бұрын

love your conversation and dead pan it makes your videos better, your comments are very good. Just love it. keep doing what you do. Thanks.

@PaulsGarage 7 жыл бұрын

+Chuck Simeonides thanks! Glad you enjoyed :D

@curtisrosenkranz1491 6 жыл бұрын

Comedy in forging! Who knew!!!

@revelationcoffee1574 Жыл бұрын

I like that your showing your trouble shooting and not just the "glory shots".

@PaulsGarage Жыл бұрын

If i didn't show the trouble shooting this video would be a short!

@papahajek5383 4 жыл бұрын

At a bronze casting foundry we made drilled 1/4" black pipe "shapes" with 2 feeder pipes that were attached to adjustable natural gas and compressed air sources. Each drilled hole became an individual touch and the "shape" corresponded to the shape of the casting mold we wanted to pre heat.

@kwcnasa 2 жыл бұрын

I learn something in this video. Thanks.

@allenhammer7923 2 жыл бұрын

I am building a double one and you did just what I needed to see. Thnaks

@Comm0ut 7 ай бұрын

Forced air is the classic way to get more heat and every blast furnace is proof it works.

@timhogan427 5 жыл бұрын

Intake for air at top, .023 mig orfice tip in the middle of the top intake, 12" of tube without stupid holes, done. The bell end is not to be put on when burner its screwed into the forge. The bell end is for testing on the bench. It will burn much better with back pressure installed in the forge

@JustinWallaby 7 жыл бұрын

Paul, I'm kind of dealing with the same issue. I also drilled the holes in the tube to try to see if it helped and then realized that the holes would be blocked by the refractory after I stuck it into the forge. I am going to try a longer tube and maybe a larger jet. (I'm using a .025 mig tip) I am subscribed now and will begin sharing my progress on You Tube as well. Keep making these videos. I love your format and videos like yours keeps me motivated to keep pushing forward with my project. Thanks!

@codelicious6590 3 жыл бұрын

I love the chimp and the mushroom cloud.

@archangel20031 5 жыл бұрын

On mine, I added a plenum with a caged fan to push the fuel and air out the front of both burners with some serious force (a lot more force than a hair dryer can supply). Even so I get the same thing out of the air suction holes happens, and I just place my finger over the hole and POOF, the air being forced in pushes everything with force and the flame shoots out the front. The issue is some of the mixture is back flowing out the holes, if you stop that it will have to shoot out the front and forcing the air (with enough force) through the pipe is the best solution.

@chaddesantis4191 5 жыл бұрын

If more KZfaqrs would realize that Grateful Dead music is copyright free, I'd enjoy their videos a lot more.

@troyparsons7253 4 жыл бұрын

One easy trick get a stainless steel scrubby ball then push it in the pipe near burner end. It will work like a back arresting setup forces the flames out past it holding it on one side of it.

@no1medic 3 жыл бұрын

This mans sarcasm is lethal

@lewisgiles8855 2 жыл бұрын

I was like number 2.3🤣too cool 😎. Great vid!

@ShootingUtah 4 жыл бұрын

Maybe this has already been said but I think if you have the holes in the side of the pipe you would want to plug the hole at the end of the pipe. It's letting air mix with fuel right at the point where the gas is coming out. You want the air coming in after the gas, your set-up has air coming in before the gas as long as the end of the pipe is open.

@srobinson1182 2 жыл бұрын

Just gotta light it at the end...not through the holes. It'll still work without the mesh but yeah the mesh is better to use. Also coz the mesh heats up red hot and makes yur flame much hotter...

@GOTOHOBBIES 5 жыл бұрын

PAUL You are absolutely brilliant and funny, just been watching your video, O man I nearly pissed my pants. Please don't stop making the video's really enjoyed watching them and I have learned some valuable lessons. Thanks Paul Best regards Dave

@PaulsGarage 5 жыл бұрын

Thanks! glad you liked the video

@dogsarebest7107 6 жыл бұрын

Hey, the reason your burner wasn't running right is because you have far too low pressure and made a screwy design. It could still work, but this type of burner doesn't run off a BBQ regulator. I didn't see what the reg you were using was, but based on sound it sounded like a bbq reg, or at least under a psi or two and possibly a much too large propane orifice. These types of burners usually run 20psi+ with a .023" or 0.030" orifice. The reason it kept sucking back into the tube is you simply don't have enough velocity to push the propane out the end and suck air in the ass end.

@poowhynot1268 6 жыл бұрын

no it was a 0-60 psi reg

@danchadwick1495 4 жыл бұрын

Do you remember the Bunsen burners in high school? Those screens served a purpose; to block the flame from coming back to the burner. If you place a fitted screen in the end of the burner the flame will stay out.

@uncleknife9887 3 жыл бұрын

Classic, you covered like 10 videos worth of shit in 10 minutes. You were never an uptight bone rub at any point throughout the entire lecture. Great Job Pimp!

@trainerlance 5 жыл бұрын

The jacket gives you legitimacy.

@PaulsGarage 5 жыл бұрын

Dress for success!

@cbsos4u1952 5 жыл бұрын

Drill your primary holes around the circumference of the pipe on the angle as you did on a line just forward of the nozzle outlet. The three holes in a line disrupt air and gas flow, the air should ender the combustion chamber from the same position around the circumference of the inside diameter slightly forward of the jet (orifice)

@TexasLonghornRanch 6 жыл бұрын

You are hilarious. I’m not sure why I watch your channel? You’re one video away from winning a Darwin Award!

@PaulsGarage 6 жыл бұрын

I hope and don’t hope simultaneously to win that prestigious award

@danielengland5 7 жыл бұрын

I have the same general type of torch and i think i know your problem. I have to turn my torch on and get the propane to hiss audibly before I light it. When I light it, I light it at the end of the torch.

@PaulsGarage 7 жыл бұрын

+Daniel england that's a good idea, I think I'm causing the problem by lighting it in the tube. Of course it will burn in the tube then lol

@badsantaclaus4522 7 жыл бұрын

Enjoyed your talking and trying to burn the house down!, Thinking right along with you, Time to melt! Just waiting on you lol

@PaulsGarage 7 жыл бұрын

+andy wilson I wasn't trying that hard to burn the house down, nothing even started smoking! I think. I didn't check.

@badsantaclaus4522 7 жыл бұрын

lol

@LowLumens 4 жыл бұрын

Pretty cool bro

@lyulf0 7 жыл бұрын

Found your channel yesterday just subscribed. You are quite funny and i feel i am learning a lot from your mistakes with some good laughs along the way. Keep up the good work :)

@PaulsGarage 7 жыл бұрын

Thanks! glad you enjoyed :D

@grendal113 7 жыл бұрын

I think we will be reading this guys obituary.

@johnneykrew Жыл бұрын

All you needed was the bell on the back. Lol, keep the new bell, ditch the hair dryer, cover the holes, and use a piece of tape over the back to adjust the amount of incoming air, and you're good to go.

@johnneykrew Жыл бұрын

P.S. love your videos, keep it up!

@PaulsGarage Жыл бұрын

you just described a different kind of burner lol I have modified this one since this, a couple times actually. The burner you suggest is a much better design. My cobbled together nightmare only has 2 modes: Perfect for aluminum, and overheat everything including cast iron lol there isn't much in between

@plutomaster234 7 жыл бұрын

I have a torch that was having the same problem, flames going back down the pipe and creating a terrible racket and very little heat. I solved it by increasing the length of the pipe. For me the problem was that the air and propane was not being mixed sufficiently and backfiring down the tube a dozen times a second. I went form a 6" pipe to a 12" pipe and the mixture coming out the end was then sufficiently mixed and the flare at the end stops the flame from traveling backwards due to the low pressure zone it creates. A well mixed flame produced a sufficient sucking power that you wont need any forced air to push the propane down the tube.

@PaulsGarage 7 жыл бұрын

+Andrew K is that the "popping" noise I hear some burners making? I always wondered what caused that.

@soupflood 4 жыл бұрын

4:50 "it's just temporary" _by which i mean permanent_ When you would like to improve, but the current setup does the job so well, it lasts years and years. 10:31 the rocket fun begins

@taitelennox4514 7 жыл бұрын

very smart

@1ericedwards 6 жыл бұрын

Hey Paul, I have a suggestion for you. A metal working friend of mine suggested to use a spark-plug designed for a coal furnace. If you rig it up in the correct place on your pipe (before where it enters into the furnace), you can flip a switch to have it spark the flames to life. Though this may seem to complicate what you have come up with, getting the fire started could be easier and as we all know how much you value SAFETY, it may be worth the effort.

@PaulsGarage 6 жыл бұрын

That’s a really cool idea! I’ve seen those things, never thought to add one here. I’m a fan of over complication

@1ericedwards 6 жыл бұрын

Awe. I'm glad you appreciate it! I have some casting Ideas myself I want to experiment with... but I need to build a bigger-better furnace. Have you heard of "steam casting" this plus "ceramic shell" could be interesting... and dangerous!

@captdigb78 7 жыл бұрын

Maybe with the dryer you could melt metal faster thus using less propane than you thought. It might be a more efficient burn. Plus you could make a blower bypass just like you made your air intake holes and sleeve but this would regulate pressure going out not going in thus allowing you to fine tune air injection and run less gas.

@PaulsGarage 7 жыл бұрын

That could work. The only way i was able to get a lean flame was using the hair dryer, so i definitely had more range of adjustment using forced air. Not that I want to use a lean flame, but without the hair dryer i couldn't even get a nice neutral flame.

@tobhomott 7 жыл бұрын

Good luck with the burner! If it just won't burn at the flare reliably... well, there's always waste oil! (come to the dark side, muhahaha...) ...Or maybe build a Reil burner. Just slightly oxidizing (lean) is what I aim for when melting aluminum; I figure it's better to skim a little extra dross than end up with casting full of pinholes. Degassing the dissolved hydrogen that unburnt fuel from a rich burn will happily provide is fun to try once (wheee! bubbles!), debatably effective in the backyard foundry, and mostly just kind of a PITA. On the other hand, you'll have to skim some dross whichever side of dead neutral you end up dialing your burner in to. Fun videos, keep it up!

@PaulsGarage 7 жыл бұрын

+Tobho Mott in hindsight a reil burner would have been a better choice, but I'm glad I got this one to work. I hadn't thought about hydrocarbons gassing up the aluminum but that makes sense, I'll keep that in mind. A little extra dross in exchange for less porosity sounds like a great trade off to me

@bravok1lo 7 жыл бұрын

Not sure what exactly I learned but it sure as hell looked cool

@PaulsGarage 7 жыл бұрын

+ThatOnePineapple I learned I can make insane amounts of fire, that's valuable information right?

@napalmholocaust9093 5 жыл бұрын

laminar flow flame holding devices (fine screens) in the bottom of your flare will decrease flame lift and back firing. the screen's depth is your flames depth. rods of different diameter are used also to hold flames. porting and smoothing the inner surfaces i.e. threads, casting lines, will reduce propane combining with enough air to become combustable inside the tube from jetties of turbulent mixing.

@PaulsGarage 5 жыл бұрын

Thanks for the tips! I've considered stuff like that, my forge burner has a screen to hold the flame. Works well

@omm7763 6 жыл бұрын

If you want the best heat/flame the propane nozzle closest to torch tip, Pressurized regulation just behind the propane nozzle and neutral adjustable airports behind pressurized airport.

@dariusroseboomdevris6052 6 жыл бұрын

Next to a child's chalkboard

@bolandvapecompany957 6 жыл бұрын

i have buildt a propane burner but i have used a vacuum as a force in pushing the butane and flame then with a stop cock to regulate the ration of gas and air wich in my opinion is much safer so you dont get any back flash

@steffankaizer 6 жыл бұрын

it lit *AIRHORNS* seriosly your vids are great i like how you hurry things along ang get to the point but also ramble endlesly at the same time

@PaulsGarage 6 жыл бұрын

Thanks! glad you enjoyed

@Kalosmon 7 жыл бұрын

Chalk 101, with Paul / Ruffles. Next, How not to videogames 101 with Mr. Cody and Basics of Glamour, with Mr. Ruby.

@brianoberhausen5153 6 жыл бұрын

First time watcher. You crack me up! Thanks.

@PaulsGarage 6 жыл бұрын

Thanks! Glad you like the humor

@Njennings42 7 жыл бұрын

So that was something I watched today.

@abbasali3100 4 жыл бұрын

I thing you have to make holes in the cup perpendicular to the flame stream your problem is solved but with the blower you need swirler to avoid yellow spot

@ryanstruk1 6 жыл бұрын

When it melts the wrench sockets on your wall, I would call that well tuned

@nitroshortbus5625 6 жыл бұрын

I could help you! I suffer from of the same disabilities and experienced the same problems. Forced air is without a doubt the idiots way of dealing with these problems put a big reducer(bell end) on the end and hook up a shop vac with a Harbor Freight speed control. Oh shit you figured it out!! Anyways, you should be a saftey officer for OSHA. Next video wear roller skates. Keep em coming, good stuff. 👍

@PaulsGarage 6 жыл бұрын

Thanks! :D

@ChaosPootato 7 жыл бұрын

Really love the tone of your videos, you earned a new sub! Keep it up!

@PaulsGarage 7 жыл бұрын

+ChaosPotato Thanks! Glad you like them :D

@nathanielritter8514 2 жыл бұрын

Bro wtf did I just watch. I'm bromancing rn

@adammoon4087 4 жыл бұрын

fun video . forced air burner will use less fuel and is much more controllable than your ventury burner design

@icysteve46 5 жыл бұрын

I put the gas pipe at the end of the burner and did not drill any holes and light it at opposite end sometimes when it's windy and when the gas pressure is to low the flame will travel up the one inch pipe and burn at the source . I just turn it off and relight it. Also in the bell at the business end I put a stainless steel drain strainer. But I see your lighting it right at the orifice. don't do that light at the end. 8*)

@justinherman9443 7 жыл бұрын

Your channel is awesome.

@PaulsGarage 7 жыл бұрын

+Justin Herman thanks!

@TheOffGridFamily 7 жыл бұрын

You Rock!! I love what I have watched of your channel. Keep up the good work man. Its great stuff

@PaulsGarage 7 жыл бұрын

+The Off Grid Family thank you, good sir!

@jukeboxhero1649 2 жыл бұрын

Gimme your lunch money

@grantbrowning4951 Ай бұрын

“By which I mean permanent” every project I do

@PaulsGarage Ай бұрын

This is the way 🤣

@scharkalvin 5 жыл бұрын

You can run a forced air propane burner at lower propane pressure. This will help keep your propane tank from freezing up.

@Tensquaremetreworkshop 3 жыл бұрын

What is missing is a mesh at the end of the nozzle. That prevents the flame moving back into the tube.

@edgeeffect 6 жыл бұрын

Last video I commented that that looks A LOT like a Bunsen Burner... well, now it's even more like a Bunsen Burner. But yeah... over-complicate it to be awesomer... it's the only way to go!

@klixtrio7760 7 жыл бұрын

This video is kinda old but I finally put my burner together after the parts were sitting forever....Anywho mine is the ron reil burner and works great. Maybe you could convert yours to that by using a bell reducer and drilling two holes into it for the gas pipe. If youre curios I used a 1-1/2x3/4 bell reducer, 3/4x6" nipple, 3/4x1 bell reducer for the flare. Gas pipe was 1/8 brass (brass is skinny and allows more air). Oriface was #57 drill bit. Good luck!

@PaulsGarage 7 жыл бұрын

I was considering a different burner but i would probably remake it from scratch. Also, i'd definitely go for forced air next time, maybe not even propane. Who knows.

@klixtrio7760 7 жыл бұрын

I considered force air but others said it used a lot more propane (and more elaborate to make). Now that I have this burner I dont think its needed. This is a picture I took of my burner at about 20psi. imgur.com/a/WKDdl

@zippy3711 6 жыл бұрын

This guy should not be playing with fire.

@PaulsGarage 6 жыл бұрын

Nobody should play with fire

@darylgardiner9820 7 жыл бұрын

u should try to put ur just at the end of a 1" black pipe in the center of a 1.5 to 1 reducer and make an small flat threaded washer to adjust air flow like Alec Steele does with his burners

@PaulsGarage 7 жыл бұрын

+Daryl Gardiner that's more like a reil burner, this is an Oliver upwind burner so it's a totally different design. The reil burner is probably better though.

@darylgardiner9820 7 жыл бұрын

you might be right I don't really know but I know I'm gonna try to build one for a forge and a smelter

@stewartbremner8660 7 жыл бұрын

still loving this guy!!!

@PaulsGarage 7 жыл бұрын

+Stewart Bremner thank you! Glad you are enjoying!

@onehappydawg 5 жыл бұрын

“This will be temporary” “By that I mean permanent” I’ve been watching you not to really learn anything but to have a laugh. Great videos 👍 Hilarious that you wear a suit jacket while building things.

@rustopholis1667 5 жыл бұрын

So i just lit my forge for the 2nd time today, and am having issues with heat traveling up the burner. NOT OK. so this video is helpful, and probably will be again. I may return with QUESTIONS! haha, thanks!

@notyouraveragegoldenpotato Ай бұрын

Man.. it took like 3 minutes flat to make a burner for my foundry that works perfectly😂 none of this nonsense. A T pipe/3 way, a 6" black iron pipe, a flare/ reducer, a mig torch welding tip, a drill bit and a tap😂 drill and tap the T pipe- thread the mig nozzle in so its pointing down the middle of the T, screw the 6" pipe and the reducer (flare) on the end. Connect gas with regulator and valve onto the mig tip.. Works perfect. If i want forced air then i set my compressor regulator at just a couple psi and stick a small hose into the T pipe pointing down the nozzle. Venturi type but also works very well as a forced air without adding excess oxygen into your flame😂

@DrumSmithRich 4 жыл бұрын

The holes in the pipe arent working because theres no venturi effect st the holes so no differential in pressure between outside the holes you drilled and whats in the pipe. A venturi effect needs a difference in diameter between where the air is before it enters the pipe and after it enters the pipe. If you had a cone with a larger diameter than your main pipe leading to the holes in the side you would compress the air coming into the pipe causing a lower pressure in the pipe and pulling the air in (venturi effect.) As it is theres no venturi at the holes hence the backflow of flame. Interesting concept though I wonder if you could make a 2 stage venturi? Good luck Broski

@josephlieberman5324 5 жыл бұрын

Using a refractroy fibre behind a screen just after the air gas but before the flame, this can act as a flame arrestor to disallow your flame from going backwards into the air mix chamber.

@brettphillips3091 5 жыл бұрын

venturiized, love it

@bikerman198923 4 жыл бұрын

If you leave the holes uncovered and had the gas all the way up and light it at the end of the pipe you wont have the flame backing up the pipe to the holes.