TBS Crossfire Beginner Guide (2023 Update)

Рет қаралды 71,769

Күн бұрын

Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: www.fpvknowitall.com/ultimate...
SUPPORT ME ON PATREON at: bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: www.fpvknowitall.com/support-me/
---
00:00:00 - It's time for a new Crossfire setup guide!
00:00:22 - Update the firmware on your module
TBS Agent Web is at: www.team-blacksheep.com/agentm/
00:03:59 - Receiver wiring to FC
00:07:14 - Configure Betaflight to recognize the receiver
00:08:54 - Download TBS Agent Lite script
Download the script from this link: www.team-blacksheep.com/tbs-a...
00:11:22 - Configure controller for external module
00:12:28 - Bind receiver to module
00:15:51 - Crossfire options: Region
00:17:33 - Crossfire options: Frequency
00:18:26 - Crossfire options: Max Power
00:19:37 - Crossfire options: Dynamic Power
00:20:37 - Crossfire options: 8ch vs 12ch
00:21:24 - Crossfire options: RF Profile 50 Hz vs. 150 Hz
00:23:57 - Tracer options: Output power
00:25:10 - Tracer options: TX Antenna
00:25:34 - Have I earned your support today?
00:26:52 - TBS Agent M is not just for flashing
00:27:33 - TBS can control your video transmitter? Yup.
My tutorial about setting up TBS MyVTX is at: • TBS MyVTX | Never powe...
00:28:14 - TBS Sixty9
For more information about TBS Sixty9: • TBS Sixty9 should prob...
00:28:49 - What if you brick your hardware?
How to unbrick your TBS hardware: • So you bricked your TB...

Пікірлер: 222

@jpaul8589 Жыл бұрын

Josh...I hope you realize that without your knowledge lots of folks would have given up. Thank you so much!

@stephenwalker3127 Жыл бұрын

Purchased a Boxer, Crossfire mini Tx and Nano Rx here in the UK. Followed the video to set it all up and all went very smoothly. A thousand thanks.

@CDRaff Жыл бұрын

Thanks for the video! I almost forgot I have a pile of Crossfire stuff that I need to list on FPV Exchange.

@thepoorboychannel Жыл бұрын

Never misses a single step. I can always count on you to have everything I need to know about my gear. Good job! I love the fact that I can configure my vtx via the receiver.

@tonymorgan328 Жыл бұрын

Thanks so much Joshua for this tutorial. This will help me out alot by having all this info in one easy to follow video. Keep up the good work.

@cyruscatfisher Жыл бұрын

This is, as always, useful! Cheers!

@dennisvandervloet8640 Жыл бұрын

This was the video I needed after all those issues with agent X and crsf v3 failsaving with betaflight 4.3 Tomorrow is update day ✌️🤘

@audiogek Жыл бұрын

I know it's a beginners guide but maybe helpful for some: If you can't reach the bind button, reset the receiver before updating tx module, it'll go into bind mode next power up automatically.

@NorthStarDrones Жыл бұрын

Excellent

@sshdrones Жыл бұрын

Thanks Joshua....Very informative

@DavidOwensuk Жыл бұрын

Excellent video JB, thank you!

@shotbyarian Жыл бұрын

great video, just bought a new radio with a crossfire module and want to switch from the dji remote - great timing

@maximumdrone5334 Жыл бұрын

Well I did learned a lot today! Thanks Joshua!

@Bikepro07 Жыл бұрын

Thank you so much for the toutorial. It helped me so much ;)

@NorthStarDrones Жыл бұрын

Another excellent video thank you JB

@chrisclark3503 4 күн бұрын

You're a huge help, thanks man!!

@npc178 Жыл бұрын

Thank you Mr. Bardwell

@skyreadyrc5873 Жыл бұрын

Hey, I recognize that quadcopter :). Love the guides!

@jurijcelestina5292 Жыл бұрын

Nice video JB

@MANTA_FPV Жыл бұрын

Still using my OG full size 2W module from these days and that thing just works and never dies and never failsaves. I even accidentally forgot to turn it off and it full powered without an antenna until the battery was emty and it survived. TBS is just making really good tuff. Also went through a lot of their receivers and VTXes through all these years, no problems!

@GC-sg9jv Жыл бұрын

Crossfire was a great upgrade to rid myself of the Frsky protocol using my QX7. No complaints and a bit better user friendly experience than ELRS. I left Crossfire for 2.4GHz ELRS last year and have no regrets with a superior F1000 radio link for LOS flying.

@gamesforkids143 Жыл бұрын

Sorry im new to this fpv, so what makes it better with 2,4GHz, and what is LOS flying?

@MCsCreations Жыл бұрын

Thanks for the tutorial, Joshua! 😊 But... Binding phrases... ❤️ Anyway, stay safe there with your family! 🖖😊

@mayberrywj 11 ай бұрын

A great informative video.....thanks...:)

@andyschmid7259 6 күн бұрын

Excellent!

@ericschellenberger612 9 ай бұрын

FWIW new Boxer old CRSF. I module followed your instructions TBS Agent Lite came up "searching for devices". After a few power cycles and trying to figure out where I went wrong XF Micro Tx came up and I'm good. Thanks for everything. I'm going to make a contribution. Soon.

@marklitvin9291 Жыл бұрын

Thanks! as usual

@bladesfpv4179 Жыл бұрын

Great refresher course on crossfire. Made me realize I haven’t updated in a while am I’m behind. Lol. I hope to see you do an updated video on the ghost system soon. @JoshuaBardwell

@MatrixQuadFPV 11 ай бұрын

great vid

@EvGen0378 Жыл бұрын

Спасибо. Отличное видео. Все понятно и доступно простому новичку.

@mrrevengaa Жыл бұрын

Thank you for your worok sir

@stevo43068 Жыл бұрын

Thanks for the update. My Tango2 is still on 6.07 😆

@PipeZnBonGz Жыл бұрын

Still on 4.11 here!!!

@4QFiles 9 күн бұрын

thanks. I learned something.

@Fly_High_FPV Жыл бұрын

The "My VTX" feature eliminates the need for fiddling with vtx tables ( BF4.3+ now makes vtx tables easy, but MyVtx means no tables). I was also surprised how many situations it is more useful than the BF OSD Smart Audio, because you dont need to have a video feed to change your vtx settings. Great if you're crashed out in the field, or on the bench.

@kenfeltman3320 Жыл бұрын

11 Days late on saying thank you got cross fire for qx7 tuesday 17th missed the post thanks again

@ericcoker8784 Жыл бұрын

I totally appreciate your hard work and these tutorials. My Tango 2 was shipped with everything wrong. Biggest problem was the gimbals, too much *grease* and calibration errors. Could not get it perfect until I took it apart and did some spring cleaning. Only then, was it perfect. My BetaFPV Lite Radio3 and Zorro were perfect with gimbal calibration. All others needed help. Then it was shipped 868 or whatever! Changed that too...(even though at close range there was not difference). But step outside of that range, my FRSKY was better or the same. But was it? The antenna looked attached, but not really....just silly how that was my fault for not checking when it was taken apart. But again, No buyers remorse. The gimbals feel really good, the binding was easy and the less is more approach is nice. I also had not a clue about *dynamic power* and some of the other functions. Ohhh, under settings called "Op Mode" , it was on *Forced Tele*...so I switched that too. Now in binds up/makes connection real fast. Not sure why, but everything seems better too.

@UnmannedSky Жыл бұрын

Yeah my Op mode was also on force telemetry which I think makes it run at 5hz packet rate which is basically unflyable on a multirotor. Almost lost my quad over a mountain as a result. Doh!

@mafiafpv3469 Жыл бұрын

My zorro came with tbs agent already loaded thank god and thank radiomaster

@kurtzFPV Жыл бұрын

You can use tbs agent to change ELRS settings also, if you like the ui better.

@SCFPV Жыл бұрын

@@kurtzFPV Not all Zorros have the Elrs radio.

@lenny0272 Жыл бұрын

I would be screwed without your info. Thanks.

@EnglishTurbines Жыл бұрын

Good job JB....I wonder when the RX prices will fall??...🤔😳😏🇬🇧

@norbertgeider5744 Жыл бұрын

Great channel and great work at all! Thank you! I just updated my crossfire micro TX to 6.19 which says it reenable the CRSF V3 protocol. But in my TX16S it still shows me CRSFshot. Could you explain me why? Is this right? Is V3 a kind of shot? And on the external module screen I could set the baudrate. Now its on 400k. Could I set this higher or is this the max. rate CRSF micro TX supports?

@rcthomas7090 Жыл бұрын

1st like ! What up Bardwell?!?! Thx 4 the great content!

@ab.flicks 11 ай бұрын

🐐 🐐

@eikepape3920 9 ай бұрын

I really appreciate all the help through your videos which are super informative and helpful so far! Anyway my crossfire Rx and Tx seem to be faulty or unable to bind. Rx shows a solid green light (FC solid red) and pressing binding buttons doesn't get me into binding mode at all. Tried everything I found in the web and followed manuals RX TX versions are the same but still don't know what to do now. If anyone has a lead where to start troubleshooting I would more than appreciate it.

@flaperon35 Жыл бұрын

good evening and happy new year my friend I need your help. I have a graupner mc-20 transmitter and I want to make it long range. has not set for an external module. Is there a way to change the transmitter? thank you very much and keep up the very good work you guys on youtube.....

@crussell5584 Жыл бұрын

thanks once again!! @joshua bardwell which sd card file should the tango 2 pro have if its updated to all the latest public firmwares i keep getting a bad sd card content error on startup and wont bind to any rxs after even after reset.

@demitrisgalanakis1634 6 ай бұрын

Hello Mr. Bardwell and thank you very much for your videos and invaluable guidance! I have a Taranis X9D Plus bound to a TBS CROSSFIRE TX LITE Long Range Transmitter and my OLED screen, in the back of the TBS agent, is so dim that you can hardly see it's working! Does this sound familiar to you? Thank you very much in advance and I am sorry for any inconvenience!

@yellow-jz4bf Жыл бұрын

we need more beginners tutorial like how to bind elrs iflight quads with elrs radiomaster tx16s

@lopesdev Жыл бұрын

Hello. I need to use a mark5 o3 crossfire version with a dji fpv remote controller 2 (using the o3 air unit). How is it possible? Do i need to disconnect any cable from the crossfire? Thank you a lot.

@kennykobi Жыл бұрын

hey JB Im just wondering my rssi changed i looked into the sensors. Is it currently rfmd 2 and rsnr 80 tsnr 70 with rpm as a value ?

@HermyH66 Жыл бұрын

There is also an option in crossfire to control the max. dynamic output by a switch, i use it to prevent the module from going to 2W when there's no rx plugged in.

@twinturbostang Жыл бұрын

If you do this, very important to link it also to the ARM switch, so that you don't forget to change the output power before a flight!

@HermyH66 Жыл бұрын

@@twinturbostang depends on what output levels are used, i have set it to 250/1000/2000mw, but yes if the lowest one is 10mw then you might want to put some logic with an arm switch in there.

@gratefultedd969 6 ай бұрын

I really thought that this guy was "brick" from an old tv show. No offense Josh. Your content is so valuble!

@sethvane669 10 ай бұрын

Hi Joshua, I have Tango 2 Pro V3, a lot of articles online talking about TBS Crossfire Nano RX tracer that you mount in the back of the controller, can you share some thoughts on it. Thanks

@helmuthuneke1775 8 ай бұрын

I had to update from 4.03 because of a new v3 RX i got low rsssi and found the rx jumps to 0w pwr after power cycle i use the channel 12 for Rssi/lq .. so my problem is the rx dont save power output max pwr. i run dynamic set up. would be very thankful for your advice

@swetunafpv1856 11 ай бұрын

i have a tx16s and a tbs nano rx that i just put in my quad i stuck in the step where the tx16s i having a blue ring light on the modulke and reciever(nano on the quad) is green. but it will not respond to activationb ocn the killswitch to set quad in idle and take off.

@BikeGuyFPV Жыл бұрын

Can't wait for the next TBS Crossfire/Tracer how-to video in the next two years!

@tweekFPV Жыл бұрын

👍🏻👍🏻

@lukaskonrad3059 Жыл бұрын

hello joshua i have a question i hope you help me, i'm lukas and i have a taranis qx7s with a tbs crossfire module a buddy tied my 5" quad back then (a year and a half ago) now i've bought a meteor 65 crossfire editon and i've been trying to connect it for a month but i just can't get it to work i've tried so many things but i'm no tech genius. I hope you help me :D

@h-dawg969 3 ай бұрын

Alright Josh? As soon as I plug a Lipo in, my quad starts beeping and doesnt stop. How do i get it to shut up? I've turned off usb tab under beeper configuration in Betaflight, but it's just constantly beeping as soon as it has power. It's well annoying as Im waiting for update/bind etc. Thanks.

@itunes530 Ай бұрын

Cant figure out the connection now. Starting to think my cross fire rx is bad. Doing this wierd thing where the rx is green like its paired. (And it sort of is). But my tx shows like a yellowish light. Which it should be green (meaning binded) and I dont know why its yellow. When i push the button on the tx. The tx goes into the green blinking mode. Which is pairing. It also makes my rx red (not bound anymore) Soon as i stop binding mode on tx. It turns back to the yellowish on tx but rx is now green like if it was connected

@nick138 Жыл бұрын

I have a Spektrum IX14 for all of my Helicopters and planes. Is it worth it to buy the module or just buy another transmitter for drones? I'd like to use my IX for all of my aircraft.

@reddexrose Жыл бұрын

Wow..... No full size crossfire love..... Savage JB

@snowhack8903 Жыл бұрын

So after I dragged the files over to my RM TX16s SD card I can no longer get the long hold scroll wheel menu to show up. Long holding the scroll wheel does nothing now. What happened?

@raffman4266 8 ай бұрын

Sir Joshua wondering why tbs agent lite lua does not have a setting to adjust the nano rx telemetry power output? Hope the devs can answer why?

@BaldBeard_BlackShirt Жыл бұрын

I have noticed with binding out of the box is that my nano and sixty9 were shipped in 868 and I would have to temporarily set my Tx to 868 then it would bind and I could set it back to 915

@JoshuaBardwell Жыл бұрын

That's surprising. I haven't encountered that.

@matttatts Жыл бұрын

So today I resurrected my X9D-plus flashed up to date firmware no problem. Flashed new TBS crossfire micro also no problem but when I open new model on my radio and try to set external RF to CRSF the radio simply blinks out and returns to the menu with out changing to crossfire. Tried different models and reflashing everything and searching but it doesn’t even seem to be a problem anyone else has had? Any help would be extremely appreciated.

@timmyhanstine9508 Жыл бұрын

random but what do you hink would be the better option the mambo or the tango 2

@doraymon4797 5 ай бұрын

Thanks @JoshuaBardwell. My crossfire telemetry is giving me big headaches. Rxbt is continously jumping from the actual battery voltage to 100% voltage, messing up the battery alerts on my radio which require 4s or more below 3.6V per cell to activate. Similarly I have continous drops of the signal and RSSI and all connected values go to minimum for a fraction of a second. I did weeks of troubleshooting, including buying a new radio (good excuse, lol), testing 2 different drones with the same TBS Nano RX module (same result), changing frequency, power, RF profile etc... Is there anything else I can try? PS Note that my drones were purchased 3y ago with Betaflight 4.1 and I now updated to 4.4 with some trouble in setting them up again...

@JoshuaBardwell 5 ай бұрын

Did you uodate crossfire firmware on your module?

@doraymon4797 5 ай бұрын

Yes, on both receiver and transmitter. It’s very strange, really. I did lots of research online but could not find anyone with the same issues. It looks like a continuous interference causing this, but I would understand that being an explanation for the signal drop, but battery at 100% really doesn’t make any sense

@dannycooper1574 9 ай бұрын

Hi Josh, can I connect this to a spectrum or radiolink transmitter? Thanks

@JoshuaBardwell 9 ай бұрын

No I don't think so.

@user-pd8yb6hh6m 6 күн бұрын

👍👍👍👍👍

@mandel4889 Жыл бұрын

Whats the diffrence between the tbs nano and micro? I want long range and live in the EU

@MANDOXsquid Жыл бұрын

I have a question for you, how long does it take to update these? Im stuck on 6.17 since I have gotten my micro. There has been 6.19 since atleast september when I first got mine. It seemingly fails each time going on 6.19. Bricks the module and its a whole hour process to get it back on 6.17 and working again. Half the time on 6.17 it fails to update. What am I doing wrong lol. Doesnt matter the pc I use, or web or desktop versions.

@abouchard2903 Жыл бұрын

I would email him or ask on a live stream, this great question might never get seen.

@JoshuaBardwell Жыл бұрын

If the module refuses to update over USB, I think I would have to contact TBS support about that. It should only take perhaps 5 minutes to complete the flash. If the flash fails, bootloader mode should restore it in the same amount of time.

@MANDOXsquid Жыл бұрын

@@JoshuaBardwell perfect thank you. maybe an issue with mine then.

@cesargurc911 8 ай бұрын

Hello, I updated my tbs micro module to version 6.19 and now I don't have telemetry, I use a taranis qx7 Open tx 2.2.2, what did I do wrong?

@M.TTT. 24 күн бұрын

I have the same issue, did u ever solve? Idk if I have to update my radio?

@ca_maple8970 2 ай бұрын

16:10 Of course I had to press FCC. How do I set it back to open? That option disappeared.

@pedro449 Жыл бұрын

Is it possible to move Crossfire Tx V2 module between two radio transmitters? I have one TX module and want to move it back and forth between my Radiomaster TX16s and Jumper Pro and be able to fly the same quad without setting up all switches (arming ...) each time. Appreciate any help

@JoshuaBardwell Жыл бұрын

Yes you can do it but you need to manually set up the switches on both controllers to be the same.

@pedro449 Жыл бұрын

@@JoshuaBardwell Thank you very much for your kind assistance 👍🙏

@loveofnature6266 Жыл бұрын

I really wish someone would put together a buying guide, TBS crossfire fpv whoop/controller/goggles etc. video. There is literally no video out there explaining this. Only "get a DJI goggle/controller" for easiest use.

@vaas2642 Жыл бұрын

Power switch also should be mentioned, great thing to have on arming switch for example...

@PMB15 Жыл бұрын

In the last video you recommended staying on 8 Channels. Do you meanwhile know the "disadvantages" when switching to 12 Channels as you know recommend to use all 12 Channels now?

@JoshuaBardwell Жыл бұрын

Yes finally the answer has been revealed, and it turns out it was what I guessed all along. When you switch from 8ch to 12ch mode, the aux channels are polled at 1/2 the rate. So 25 Hz or 125 Hz. Instead of sending ch. 4-8 in every packet, it alternates between 4-8 and 9-12. So if you were using the channels to drive servos, the update rate might be unacceptable, but if you are simply using them as aux channels with a multirotor, it's fine.

@WATCHMAKUH Жыл бұрын

Anyone know if TBS will be releasing the PRO version of Crossfire Diversity Nano RX with 500mw output power?

@shotbyarian 4 ай бұрын

what baudrate should i chose on my edgetx remote? 400k? 921k?

@JoshuaBardwell 4 ай бұрын

400k is sufficient for Crossfire.

@eraneichler4732 9 ай бұрын

If i have updated my cross fire module will i lose my recover binding?

@undeze 8 ай бұрын

After updating my crossfire module I had to rebind the receivers on my quads.

@PavLosMavRis 6 ай бұрын

Is it possible to change my region after I select it? If i'm traveling to Europe I want to change it from FCC to CE

@JoshuaBardwell 6 ай бұрын

Yes I show how to do it here. kzfaq.info/get/bejne/obKZid2gs7momGg.htmlsi=x4O0OM4QIRIsthee

@soflo_fpv2 Жыл бұрын

Im on Betaflight 10.9 configurator runninf BF 4.4 on my Diatone mamba f722 APP, and for the life of me i cannot get stick inputs to show up in betaflight. I checked the ports amd tried rewiring the rx and tx wires to different port numbers with no luck. also running agent lite version .92 with tango II xf version 6.19 and the RX firmware is also v6.19. Has anyone else been having this issue at all? This video was great help for me to get to know this radiomaster boxer i just got. With all of this crossfire hassel i might have to swith to 2.4 and move to ELRS but I do like TBS and crossfire but this hassel just may not be worth it any help woullld be aweeeesooomeee

@zenzfpv6304 Жыл бұрын

Is it still possible to get the full tx

@RoyCruse 6 ай бұрын

Before you recommended to use their latest firmware, including beta versions. Is that still the case ?

@JoshuaBardwell 6 ай бұрын

Yes.

@RCCRAZYSTUPID Жыл бұрын

Great video on crossfire, I would like a video on ELRS just like this video. Nice job jb🔥🔥

@JoshuaBardwell Жыл бұрын

Ok here is it's 😊 kzfaq.info/get/bejne/gJl4mpWXnLiwYXU.html

@gregorydahl 7 ай бұрын

How much do you want to show us how to make a ground station tripod with a walksnail and a crossfire module on it ? So we can fpv inside with a projector screen and have the spotters outside ? Or is that even possible ? A small whoop or radio controlled car even ?

@calypsocostelo2482 Жыл бұрын

I still remember the days when you and TBS wanted to "kill" each other. It's nice to see that you are friends know. Today I learned from you how to make friends with former enemies and I got a looong list... 🤣

@coleslaw5560 10 ай бұрын

i need help, why my receiver not flashing any lights Thanks

@lionelttl Жыл бұрын

Is there a way to update my crossfire TX without having to rebind and update all my receivers again?

@antoineozaneaux6881 Жыл бұрын

if they are already bound , just update the TX and the RX will get the updates over the air . once you power up the quad

@JoshuaBardwell Жыл бұрын

After updating the TX, the receiver should still be bound. If you power up the TX and put it into bind mode, then power up the RX, it should immediately say, "Update RX?" without needing to press the bind button.

@saturn_fpv Жыл бұрын

@@antoineozaneaux6881 Depending on the version jump you have to rebind all recievers. Another comment mentioned the workaround to reset reciever first, so it will go into binding mode next time you power it up. Makes it a bit easier.

@KaraiAleru Жыл бұрын

I'm following through this guide, but my nano RX does not enter binding mode (blinking red) even after I push the button. What could be the problem?

@JoshuaBardwell Жыл бұрын

What is the LED doing?

@KaraiAleru Жыл бұрын

@@JoshuaBardwell Stays in red, no matter how much or little I press the button. Pretty strange. However, a couple of desperate restarts got it working and binding correctly now! No clue of what it could have been. After that, the rest of the guide helped me with the rest of the configuration! Thank you very much!

@w1llyFPV Жыл бұрын

@Joshua Bardwell I'd like to ask you about 8vs12 channels before (2 years ago) you claimed that 8 channels is the better than 12 channels (because TBS said so without any reasonable explanation) and now 12 is OK? What has changed?

@JoshuaBardwell Жыл бұрын

TBS revealed that the only difference is that in 12ch mode the aux channels are updated half as often.

@dinkermcplinker7324 Жыл бұрын

@joshua bardwell hey Josh Hoping to get some helpful answers if your are willing, I just finished my 5 in tbs one and watched your vid on motors revving by them selves on the bench with out props, I understand that’s normal, but with mine with the props on when I try to fly it it gets of the ground at about 15 to 25 percent throttle then shoots straight into the air full throttle like a bat out of hell no control until I smack disarm and catch it, in receiver on bet flight it looks fine when I move gimbals and rotate drone. driving me nuts searching google so I thought I’d try to ask you. I have 1900 kv emax ecos skystars 55amp f405 hd2 stack fly sky a8s receiver and rush fpv race 2 vtx.thankyou josh so much look forward to a response love your vids man! Thankyou!!!

@JoshuaBardwell Жыл бұрын

My guess is your motors are spinning the wrong direction. Assuming you are on Betaflight 4.3, go to the Motors tab and first run the Motor Order wizard, then run the Motor Direction wizard.

@dinkermcplinker7324 Жыл бұрын

@@JoshuaBardwell thanks man ! Even if it takes of fine? It doesn’t flip around or anything it goes full throttle instantly. Flies straight as an arrow up till it hits the ceiling. I’m running a f405 55a skystars hd2 with a 3s lipo 2200mah 35c and 1900 kv motors. Your supposed to flash in blheli and then flash in beta flight right? Thanks man I appreciate it!

@SCFPV Жыл бұрын

@Dinker Mcplinker Sounds like your filters slider may be set too high or low. A lot of noise getting to the gyro. Had this problem on a couple builds myself. I'd arm it, bump the throttle, and to the moon she goes. Adjusting the filters fixed it.

@QuadographyAustralia1965 Жыл бұрын

Josh, Mate help please, Boxer......Did the agent lite update, But where you skipped those files to update, I replaced them to update to 0.96, Now Tbs Agent lite will not load form the first TOOLS menu.....Error message reads......(Syntax error ?:0 attempt to call a nil value)......It will load from...Scripts/TOOLS...This is the only way to open Tbs Agent Lite.......and I'll be buggered if I know! Cheers mate, Jas.

@JoshuaBardwell Жыл бұрын

Are you sure you've got the latest version of the script?

@QuadographyAustralia1965 Жыл бұрын

Well that was an adventure, I deleted the 2 TBSAGENTLITE lua scripts in tools...Not the TBS agent lite folder... Then went to my taranis saved sd files on pc and used those 2 lua scripts from it's sd card.....which is on EdgeTx 2.8.3.....Copied the 2 lua scripts over to the Boxer sd and Bingo! All there and working as it should....still weird! Cheers mate.

@tomblanckaert6055 Жыл бұрын

Had an issue where i bound the crsf nano rx and after replugging it started to radiply blink green.. after some digging i tried to reflash current software (6.19) no luck same scenario, downgraded to 6.17 same scenario.. back to 6.19 and tried the emergency update, same problem.. replaced with an older nano rx.. works fine.. so maybe just a faulty one? Unless somebody has some extra insight for future events? Current faulty one has met the hammer

@TheFruitcake1983 Жыл бұрын

Try to write to the official technical support, attach to the message all possible information with photos.

@gregorydahl Жыл бұрын

Press and hold til it blinks , let up button( blinks slow ) press again within 1 second hold blinks or something . , un power plug in again and bind mode is slow blink or double blinks Hard to remember elrs and crsf are similar and months go by . And the button is small and . Jb says press once it blinks red for bind . Mine never does that but don't throw it away . I used a phone charger and the red and black usb wires are 5v for testing 5volt 2.5 a. Stuff

@gregorydahl Жыл бұрын

Thats why you are not to press " region" . Or all the recievers need to rebind .

@n8zfpv Жыл бұрын

Mombo, tsk tsk tsk :) 3:48 - 3:58

@n8zfpv Жыл бұрын

I find it hard keeping it all straight myself :)

@digitaltitan Жыл бұрын

I tried the 150hz preset with dynamic mode off. My Tango 2 was yelling at me way too much about LQ so I went back to Dynamic mode. I don't mind it but maybe I would be a better pilot without it....who knows.

@JoshuaBardwell Жыл бұрын

Rather than use dynamic, I would recommend locking at 50 hz.

@digitaltitan Жыл бұрын

@@JoshuaBardwell I’ll give it a shot. Thanks JB!

@BlockHeadsCreations Жыл бұрын

IN YOUR UPINYUN WUT IS THE BEST PV DRONE FOR BAD FLYER

@ericmac564 10 ай бұрын

When I go into radio setting in Agent Lite on my FrSky DX9 Plus, I dont see the option to set the region. My menu is: Max Power, Dyn Power, Power Switch, Encryption. As of late, I have switched my FrSky from ACCST to EdgeTx and have a Crossfire Tracer Tx module with a Tracer Rx on my Flywoo LR. I have flashed the board in beta flight to the latest firmware, added the lua script to the Tx and setup a model. I am able to bind to the model but cannot get any channels to work. My stick inputs dont show up in beta flight or the Edge Tx companion in simulation or calibration. I can plug the FrSky into my computer and play Uncrashed, but nothing seems to work outside of that. I have tried both UARTS in bata flight, reflashed the both the FC board and the controller with no luck. Anyone have any ideas? Im about to give up on this.

@JoshuaBardwell 10 ай бұрын

Tracer operates in 2.4 GHz and does not have region setting. Region is just for 2.4 GHz.

@ericmac564 10 ай бұрын

I wished this helped, sadly, it does not.

@ericmac564 10 ай бұрын

@@JoshuaBardwell I bought the quad a few years ago and believe it originally had a frsky receiver. I put a TBS Tracer Rx on it… if I flash the quad with the suggested firmware, could that be why it’s not receiving a signal?

@JoshuaBardwell 10 ай бұрын

You would need to reconfigure the FC to work with the Tracer RX. It won't be a drop-in replacement.

@shanmuganathan3738 10 ай бұрын

hai sir, i have installed crossfire filmware and sdcontents. the folder appear on my taranis qx7 then after i executed i found my crossfire nano reciever but i cannot select or click it. can you help me with that?

@leea4839 3 ай бұрын

Did you ever find a fix? my QX7 doesnt want to run some lua scripts and 'crossfire.lua' says waiting for Crossfire

@shanmuganathan3738 2 ай бұрын

@@leea4839 yes, i fix it.... install Tbs on laptop than or use qx7 to update your crossfire, then only you can access. but for my i cant do with qx7, i use laptop.

@M.TTT. 24 күн бұрын

@@leea4839 same issue here after updating my cf module, any help?

@leea4839 24 күн бұрын

@@M.TTT. Hey mate, I ended up following a different video and manually bound my receiver to my QX7 which worked. the youtube video is called 'How to bind Crossfire and Taranis - the EASIEST and FASTEST way (no luascripts!)'

@M.TTT. 24 күн бұрын

@leea4839 ah alright, thank you for replying! I actually ended up updating my qx7s to the lastest openTX x.x.15 and then it finally worked with the crossfire nano TX module with 6.36 firmware. Both my nano receivers also bound and updated fine. I see they have "edgeTX" for radios now, but I didn't feel like risking it switching over.

@bhuvanverma7223 Жыл бұрын

Will tracer work with f7 v3?

@JoshuaBardwell Жыл бұрын

Yes it'll work with most any FC.

@twinturbostang Жыл бұрын

I hate software that forces you to register an account with the company for no good reason. The Agent X application allows you to skip account registration/login. At least for now anyway. But the Agent Web does not. You have to create an account to use it.

@madladdan Жыл бұрын

Agent X is now called TBS Agent. It's still an application.

@JoshuaBardwell Жыл бұрын

TBS recommends that you use Agent M / Agent Web as of about 6.17 I believe that was the case. There was some problem with Agent for PC and it was causing issues. Maybe they fixed it.... I don't know I just switched to Web.

@madladdan Жыл бұрын

@@JoshuaBardwell Ah didn't know