Team Associated RC10B6.4 91992 Ball Differential Build setting and testing

Рет қаралды 6,397

Күн бұрын

We show you how to build up install break in and set up the ball diff for the awesome Associated B6.4.
This is pretty much the same process for any ball diff
This is part number 91992
00:00 Introduction
00:20 Component layout
00:40 Diff ball install
01:25 Drive rings on to outdrives
02:00 Thrust race assembly
04:00 Diff assembly
04:40 Tensioning spring install
05:20 Tigthening diff
06:10 Diff finished
07:00 Installing in car
08:10 IMPORTANT NOTE
09:30 Setting diff up
10:50 Break in process
11:15 On track testing - awesome
Find our Facebook page to order or leave a message for all your 3d printed needs / customrc3dprints

Пікірлер: 22

@isaiahfurrow7414 Жыл бұрын

Recently built a T6.2 kit, and a B6.4 kit. Tuning the Buggy for an indoor track, fairly high grip dirt, smooth and fairly tight ... Going to throw the T6.2 ball diff in until I can get another one... and some other changes... hope to gain rear grip out of the corner...

@TeamRC3D Жыл бұрын

Ball diff may not last long on high grip tracks.

@isaiahfurrow7414 Жыл бұрын

@@TeamRC3D it's fairly high grip, for dirt... but still dirt not like sealed clay with slicks... I think everyone running 2wd are on ball diffs, but I might ask around ... If I were to go back to a gear diff I think it would need some really light oil, any suggestions there?

@TeamRC3D Жыл бұрын

@@isaiahfurrow7414 if everyone else is running ball diff then go with that - just make sure it is set up correct and not slipping as it will destroy itself if slipping

@cyclonerc1625 Жыл бұрын

Nice driving car looks good on the track. Thank's for Sharing Mate 👍💯✌

@stevekirk2985 Жыл бұрын

I would recommend cleaning off the black grease you have used to lube the gearbox. Its known to quickly contaminate the clear ball diff "stealth" grease. This causes the diff to slip prematurely. Ae recommend using the clear "stealth" grease to lube the gears and avoid this contamination. Keep the black grease purely for the thrust race. By doing this your diff will last a lot longer. Hope this helps.

@TeamRC3D Жыл бұрын

I’ll try that

@AbbyRCToys Жыл бұрын

Thanks for the video mate

@TeamRC3D Жыл бұрын

Thanks love this car

@-1-2-1- Жыл бұрын

I see Spencer Rivkin and others demonstrate adjusting the tension without removing the drive shaft and using the hex wrench. Instead just jamming one drive cup and rotating the other wheel by hand. This seems way easier, so why do you not do this?

@TeamRC3D Жыл бұрын

Never liked doing it like that can fell it better this way but have done it before when in a rush

@FarmerFpv Жыл бұрын

The car performs great. Excellent driving, sir.

@user-ud5xw8ox8g 6 ай бұрын

I may be switching from Losi to AE just for the Diff accessibility alone.

@TeamRC3D 6 ай бұрын

Although the B7 uses a different diff!!

@karlp3840 Жыл бұрын

Thank you. Great informative video. Question, as a rookie carpet racer what is the benefit of this dif over the one in the box and would this dif help me as a rookie.

@TeamRC3D Жыл бұрын

Carpet i would use ball diff - less maintenance and better performance - ball diff off road when bumpy

@johntuffy5721 10 ай бұрын

putting grease between the rings and the outdrive will cause the rings to slip

@TeamRC3D 9 ай бұрын

Never had a problem

@HL-OOI 11 ай бұрын

Nice track and driving but not enough jumps.. 😂there is on-road track there as well..

@TeamRC3D 11 ай бұрын

Best track we have that is near to us. Is a great venue

@jamesreynolds4467 Жыл бұрын

Thrust washers are not the same size. I called Associated they measured some and they were different diameters. No preference for caged ball direction. I would put the smaller inside diameter washer against the thrust bolt head.

@TeamRC3D Жыл бұрын

Yes your are right we have found this on some ball diffs the thrust washers are slightly different sizes to prevent them fouling the drive cup