Tech Basics - How to thread a rod

Рет қаралды 55,422

IMAT

5 жыл бұрын

This video is about My Movie 15

Пікірлер: 34

@timhardy6770 Жыл бұрын

Thank you for a clear and simple video. After watching it I reground the taper at the end of the shaft and that finally allowed me to get the die started. Very satisfying feeling when it’s all done.

@markkulepisto1159 7 ай бұрын

Perfect demonstration! thank you for the learning experience

@johnmorrisnyagado6364 3 жыл бұрын

Good content. Thanks for uploading

@bringinghopesup6680 2 жыл бұрын

Thanks man I’m going to do this to my coilover I bout a new set and using my impact I snapped the damn thing now I need to rethread thank you

@hawsrulebegin7768 Жыл бұрын

Very helpful and clear. Thanks for sharing

@bondjovi4595 2 жыл бұрын

helpful hints, good sir

@JenkinsBoatWorks 2 жыл бұрын

Cool

@hvacr3194 5 жыл бұрын

Good👍👍

@apapay01 Жыл бұрын

Good video

@BunkerBlog 2 жыл бұрын

Would this work on a keyed shaft?

@nickschott4217 5 ай бұрын

No adjustment on the die set screw for depth of cut?

@Aviator168 4 жыл бұрын

Thank you. exactly what I was looking for. Does this technic work for a tube/pipe?

@Mikesfilmss 4 жыл бұрын

If I had to guess but idk we use a rigid pipe threader.

@shahadathossainrasel7058 Жыл бұрын

Where to get the DIY and how you determine the sizes?

@scottydiver5114 Жыл бұрын

How do you ensure it starts straight, and not crooked, without a guide?

@BHZ427 Жыл бұрын

What was the actual size of the precut rod?

@pobrichi 6 ай бұрын

How do you measure rod size and match die to rod?

@threadrodforeman Жыл бұрын

Good

@user-cd7jx2td8n 8 ай бұрын

@IMAT - This informative video is getting on the older side, so I don't know if you monitor it these days, but I've got a question about threading pipe that I hope you can answer for me. I've got a project in mind that will require 1.5" threaded rod in 4-foot lengths. As you can imagine, it's extremely expensive to buy this type of threaded rod, so my question is whether or not it is possible to use a ratcheting pipe threader to cut usable thread along the entire length of a 4-foot section of steel pipe? The ideal being to use less-expensive Sch 80 steel pipe to create an alternative to 1.5" steel threaded rod. Thank you for any help.

@Mikesfilmss 8 ай бұрын

i’ve been absent for a while, but I’m trying to answer all my comments. Pipe threads are tapered, it's what makes them seal or are you just trying to use a pipe threader to do this job with regular threads?

@user-cd7jx2td8n 8 ай бұрын

@@Mikesfilmss I'll be needing to run nuts up and down the threads. The ideal is to use multiple threaded pipes as vertical supports for very heavy duty 2" thick wooden shelving. The spacing of the shelves needs to be adjustable; hence, the need for threads along the entire length of each 4-foot length of pipe. Thank you for giving this some thought for me.

@melissanigh7052 8 ай бұрын

A heating and air conditioning shop could cut extended threads on gas pipe for your project. They have machines adept at doing this. You would not want to attempt continuous threads with hand power.

@9Fahim Жыл бұрын

how to stop rod from spinning in the vice. some reason a new tap albeit from China seems to grab the rod

@silverssonyoutube8438 3 жыл бұрын

Is it a harder job to do it to stainless?

@petermarsh4993 3 жыл бұрын

You bet, stainless is a harder metal than mild steel. Be gentle with your dies or they will break.

@nickschott4217 5 ай бұрын

Go slow very slow, 1/4 turn ,(stop and count 1,2,3 in uiur head)1/4 turn ,(1,2,3) 1/4 turn(1,2 ,3)

@RipRoaringGarage 3 жыл бұрын

Is there a trick for doing this to aluminum? The whole rod breaks off like butter after 2 threads. Yes, crappy aluminum, but I cant make the part from scratch anymore...it already cost me a serious injury and I just want to get this this done...

@eviscero Жыл бұрын

what OD rod?

@RipRoaringGarage Жыл бұрын

@@eviscero I managed to do it...it was a very small component in an alcohol pump. About 3/8" I ended up starting over, with better aluminum, or was it a steel piece...I cant remember now, but it did work. The rubber cups ended up being a pain (used vacuum caps that I cut).