The 3 DAY Timing Chain Job On My CHEAP V6 Camaro Is DONE

Рет қаралды 352,703

4 жыл бұрын

I bought my $4,000 2011 Chevy Camaro RS with failed timing chains. The 3.6L LLT V6 might make 300HP but it's notorious for timing chain failure. The sludge build up inside this engine probably contributed to the chain guides wearing out at only 128,000 miles. Replacing the chains is no small job but I do think it could be done in any home garage. Just take your time and use this video as a reference: • Melling Timing Kit for...
VERY EXPENSIVE TIMING CHAIN SET:
www.oreillyauto.com/detail/b/...
Timing Cover Gasket Set:
www.oreillyauto.com/detail/b/...
Valve Cover Gasket Set:
www.oreillyauto.com/detail/b/...
Accel Ignition Super Coils:
www.holley.com/products/ignit...
MERCH: shopWatchJRGo.com
Shop Motul: motul.com
---------------------------------------------------------------
Common Questions:
What motorcycle do I ride? A few. Ducati 1198, Honda Goldwing, Honda Grom, Honda Ruckus
What do I do for a living? Make KZfaq videos.
Can you wheelie? No, I suck.
Are you fast? Sort of. I suck mostly though.
Where can I keep up with you off the bike?
Instagram: WatchJRGo
Facebook: WatchJRGo (or JRGo, FB hates my branding)
Do you go to school? College, for 2 classes.
Why do you ride so dangerously? What do mean? I was doing 25.
Do you go to the track? Of course, hopefully there will be videos in the future.
Do you play video games? No, but I might stream N64 Goldeneye at some point. Twitch: WatchJRGo
Are you afraid the police will watch your videos and arrest you? Something something evidence something something warrants and due process of law
#CarRescue #V6Camaro #CheapCamaro

Пікірлер: 876

@DKTPAirsoft 4 жыл бұрын

Get the camaro w the 8 explosion holes

@WatchJRGo 4 жыл бұрын

I have one of those, but it's the older 8 exploder and probably makes less power than this V6 😂

@DKTPAirsoft 4 жыл бұрын

WatchJRGo thas crazy man rock on

@darinr9424 4 жыл бұрын

Yea but if it was me? I might.... And I say might put an lf3 or lf4 in there there.. ever seen the specs of that crazy v6?. Holy chit the lf4 is crazy.. then modify it a little ... Gawd

@terrybaptist795 4 жыл бұрын

How picking up ZL1 camaro for the channel?

@pervertedspeed164 4 жыл бұрын

@@WatchJRGo that V6 makes maybe 15 - 20 more HP at a very high rpm, and that old LT-1 makes a lot more torque at much more favorable rpms. I'll take the older V8 any day. Plus, they respond well to mods and they don't sludge up like this modern junk. I love the 90s LT-1! And then, that sound....... mmmmm

@eric1985elcamino 3 жыл бұрын

As a GM tech, one tip is that you want to pin the gas pedal to the floor and crank it before firing it up after doing timing chains. That disables the fuel injectors and prevents the engine from firing while still allowing the engine to build some oil pressure. Occasionally these 3.6L engines as well as the 2.4L engines will jump timing if you just fire them up immediately due to the lack of oil pressure present to back the newly installed spring assisted tensioners. The tensioners use a "locking/ratcheting" mechanism to hold tension, so after they have cycled oil pressure through them initially, they're good to go.

@armandotorres6879 Жыл бұрын

So basically press gas all the way down and start it up? Gotcha, thanks for the tip!

@christopheroliveriii3985 Жыл бұрын

Thank you Eric for this input, I'm on my 3rd time timing chain on my Buick enclave and this was the perfect explanation that I have been looking for!

@kamistake Жыл бұрын

you do you mean "crank it"

@gordfam1 Жыл бұрын

Pedal to the floor makes the computer cut the injectors it’s a clear flood mode it does work

@jtmartin8445 Жыл бұрын

Meh it was just a timing job. It’ll be fine as long as you lubed up the chains and guides when you out everything back together

@JonBlondell 4 жыл бұрын

It's extremely nice of the Ninja to let you take up space in his shop!

@MuitoDaora 4 жыл бұрын

He is probably paying for that.

@jeffeastman625 4 жыл бұрын

Yeah, those chains would be an ABSOLUTE NIGHTMARE on the floor of your garage at home. Bad enough in a shop.

@Cragified 4 жыл бұрын

@@jeffeastman625 This timing chain job is easy compared to some other GM products. Where you have to nearly disassemble the whole front of the vehicle like the GMC Canyon. kzfaq.info/get/bejne/Y8p5ZdOE0rPdaIU.html

@corbingreiner9879 4 жыл бұрын

I'm still geeking out The Car Ninja and The Wizard are buds. We need a third channel Adventures of Ninja and Wizard. lol

@biggmikemaynetvtx 4 жыл бұрын

Hosted by John Ross

@LegitCheckers 4 жыл бұрын

I would definitely subscribe!

@oguzgonul2584 4 жыл бұрын

It sounds like a RPG game

@kim.jong.skillz 4 жыл бұрын

@@oguzgonul2584 it basically is lol

@BoopBobBeep 4 жыл бұрын

D&D adventure lol. D&D= Drag & Dyno

@805NAVE 4 жыл бұрын

I freaking LOVE that Tyler is driving the Nissan Quest LOL

@djizzynyc 4 жыл бұрын

i love that van!

@ceetwyce335 4 жыл бұрын

He loves that van. He did a video on it. 🤣

@racer98 3 жыл бұрын

somene needs do a rear mount turbo kit on the van with NOS !.........................plz !

@scottfirman 3 жыл бұрын

I own one, he won't keep it long. They are a pain in the rear doing timing chain and guides on them. I just did mine. Never again.

@bryantmatthews93 3 жыл бұрын

he is original

@emericaman16 4 жыл бұрын

I'm loving this Camaro content way more than I thought I would. Also, would love a other boat rebuild.

@danegrossnickle2550 4 жыл бұрын

Congratulations, your mullet is growing

@chrisnorton2837 3 жыл бұрын

Isn't everyone's? 😃

@gooondie 4 жыл бұрын

Last time I was this early, JR was still flipping old Accords ❤️

@805NAVE 4 жыл бұрын

Both got V6s, but the accords were actually reliable haha

@MrWarneet 4 жыл бұрын

A joint design and development with Holden here in Australia... JR we have hundreds of thousands of them on the road over here where they've proven to be ultra reliable when regularly serviced. We even exported them to SAAB for their high end models... You may need to drop the sump to clean the oil pickup screen given yours had so much sludge.....

@_dmfd 4 жыл бұрын

Speaking of Saab, they had a really bad design with the pickup screen that would clog and starve oil back when GM started doing the OG 9³ / 9⁵ from 98 - 04 with the ecotech. They made a PCV update to fix them tho. Super easy fix but people pick them up dirt cheap, don't wanna maintain them and drive them into the ground. Kills me man.

@_dmfd 4 жыл бұрын

@I Know Better people don't wanna spend the extra $10 for dexos during oil changes and this is what happens 😂😂😂 it blows my mind how people can just run their cars to the ground

@ToasterCoasterAdventures 4 жыл бұрын

@@_dmfd its not the real fix, they sludge up because of many reasons like extended oil change and the exhaust running right next to the sump which is made of really good heat conducting alloy, I still love saabs but...

@ToasterCoasterAdventures 4 жыл бұрын

they are a shit pile motor even when serviced as gm requires, you do the chains only to find you need to replace the cam phasers... just burn it haha

@_dmfd 4 жыл бұрын

@@ToasterCoasterAdventures yea thats what I was saying in my 2nd comment. People don't wanna maintain them, use proper oil etc and drive them to the ground. The PCV helps alot tho, I've owned many Saabs haha, cleaned many pickup screens 😂

@ajw828 4 жыл бұрын

That expression of joy and happiness when it all works when you turn the key :) Great job man! I'd love to tackle a timing chain job someday.

@navaho5430 4 жыл бұрын

Hey I'm a mechanic and I'm impressed, THIS IS A VERY COMMON PROBLEM WITH THIS ENGINE AND IT IS STILL A 6 HOUR JOB, BUT YOU HAVE TO DO THE PCV MOD CHEERS FROM OZ.

@ericupchurch6167 4 жыл бұрын

Wth is that

@andreypaliy6508 4 жыл бұрын

GOBBLESS BROTTDR

@_dmfd 4 жыл бұрын

Does the 3.6 in the 2012 Malibu need the PCV update as well? I noticed his pickup screen was super clogged up. I bought my GF a 2012 3.6 Malibu last year with 50k on it for her daily and so far so good. Don't want her starving the engine tho if it has the same pickup screen design..

@jefferyepstein9210 4 жыл бұрын

David Dawson Even if the motor doesn’t screw up the transmission will go out. Sell it before 100K miles. Malibu’s and Impalas are junk.

@StreetKid247 4 жыл бұрын

Coupla ve commos aye?

@billynunns 4 жыл бұрын

2:15 I hear Tyler's intro music playing 🤣

@WatchJRGo 4 жыл бұрын

The Car Ninja and Mike were watching the trip video 💯

@danielseelye6005 4 жыл бұрын

Good catch. Didn't get it until you mentioned it.

@unbiasedcobra6672 4 жыл бұрын

There are dedicated bolt holes for removing the timing cover. No need to risk prying it off just screw two bolts in and the cover falls off.

@mambi74 2 ай бұрын

🙏

@eddiepatterson5025 4 жыл бұрын

That job looked very intense and took a lot of patience with time. Looking forward to seeing the headers installed and giving it a performance Tune. 🏁🏁🏁👍

@meatbeansandcheese 4 жыл бұрын

I loved the Camaro content. Seeing someone's disregarded mess get restored to running condition was really interesting. Definitely need something similar in the future.

@GrosserCronox 4 жыл бұрын

Loving this channel and how you're fixing and modding a V6 Camaro hope to see more performance mods to it!

@pops55650 4 жыл бұрын

Hooker exhaust, that’s the name on the box he pointed to

@juxtarepublic6106 4 жыл бұрын

Currently under harsh lockdown in Australia.... Always look forward to the JR & Co. vids..... to brighten my day... Great to see the comradery with Hoovie....

@allypaly2149 4 жыл бұрын

Really enjoyed this EP, felt like I'd been waiting on the timing belt ep for ages. Keep it coming JR 💪💙

@michaelbaka4777 4 жыл бұрын

Watching because of my '11 Traverse with the same engine! I mean, I love JR's channel; just that I have that same engine and this job was done right before I bought it. Not sure if the PVC was done up, though. When John does his, I'll be taking notes!! Congrats on a well-done job.

@colescrustycars 4 жыл бұрын

I heard a cam phaser raise hell on startup. Every 3.6 that I put chains in I ALWAYS replace all 4 phaser.

@wall4xxx 3 жыл бұрын

good job you dont want come back to that nightmare on engine lol

@jimpert6752 3 жыл бұрын

Had the same thoughts!

@dextersmithbsee 3 жыл бұрын

I'm an electrical engineer but I have to really focus to keep up in this tutorial. I'm not master automobile technician by any stretch of the imagination but I've learned a few tidbits from this session. It's a lot of fun and I thank you for the displaying a tiny fraction of your overall knowledge.

@mikenonya3167 3 жыл бұрын

Just snagged a 2010 V6 with the LT package for 11k with only 74k miles 😉. I really dig it.

@intrepid5684 3 жыл бұрын

Great job JR. I love your passion. Keep up the good work!

@tbskirk 4 жыл бұрын

Hey JR did you by chance modify the PCV so this 3.6 doesn't sludge up again?

@214blackandwhite 4 жыл бұрын

"This video is sponsored by 2 Chainz" LMAO

@atx-cvpi_99 2 жыл бұрын

It’s 3 chainz

@timchilders3535 Жыл бұрын

Hi guys. I just did one of these, complete timing set, the chains were absolutely stretched to the max, and ridiculously loose. The crank reluctor wheel had also slipped. So, I did a new crank, all new timing chain components, all new guides, chains, phazers, crank gear, crank idler gears, plus all new tensioners. Pulled left side head also, due to very low compression, middle cylinder. Found both intake valves both just slightly kissed enough to explain the very low compression in that cylinder. Put it all back together, and it's a sweet running car now. We just let the motor/transmission/front suspension, all out with the subframe, one nice complete unit. It's stupid easy to drop that drivetrain, as long as you have a lift, and a big metal table. I call mine the operating table. We had this last one, motor/trans/lower suspension/subframe, from pulling the running car in the shop, out, on the table, in slightly less than 45 minutes. That's with myself, and a guy that works for me doing it. Sweet car to work on.

@superfred6063 4 жыл бұрын

Great video. Nice to see what that job entail and will be interesting to see if the check engine light goes away now.

@Smokezors 4 жыл бұрын

I'm super early, thanks for great content! Watching you makes me more adventurous when I'm fixing my cars! Thanks!

@rickyzlab9910 4 жыл бұрын

Great video very informative and great steps to cleaning and repairing. And fun times with Tyler

@scottcol23 4 жыл бұрын

Last time I was this early John was still waiting on the crank shaft for the john deere

@andrewhillman9632 4 жыл бұрын

So happy to see the Camaro come back to life. Funny to hear Tyler say ‘it’s been a while since he’s been John Rossed’ 😂

@JackBWatkins 4 жыл бұрын

All these car you tubers in Wichita, is this the heart of the Mid-America Car Mafia? Daddy Doug, the Don, runs the whole nation with Hoovie, Ed and Freddy running their own territories. Don’t know what their game is yet, but the investigation has just begun.

@Gabe-ABNCW3 4 жыл бұрын

😂🤣

@fazejones215 4 жыл бұрын

Oklahoma too

@Robsav-yx6vi 4 жыл бұрын

Awesome work John Ross , that was more complicated than it even sounded No wonder they charge 6 hours . Whoever buys that car from you will be very Lucky because its just like NEW . Thanks again for explaining process for all Of your viewers to follow along please know it’s appreciated.

@timfenrich5328 4 жыл бұрын

Best one armed mechanic on KZfaq 👍

@ProjectZGarage 3 жыл бұрын

I have been putting off doing the Timing job on my F150 and you just reminded me i need to get it done. I already got all the parts just need to find the time to get it done.

@williamscoufaras7045 4 жыл бұрын

Great job, JR! The car sounds pretty healthy now! 😁

@kennethrogers3687 4 жыл бұрын

We love torque settings! Always helpful! Thumbs up bud!

@jaredmauldin8309 4 жыл бұрын

I love these videos at the Car Ninja's place. Great progress with the Camaro. I'd love to see you rebuild an RX-8 and flip it

@d0cx 4 жыл бұрын

Same!!!

@garykuhn1921 4 жыл бұрын

The motor is so small. Should be easy??? I love the RX8 and those taillights.

@WatchJRGo 4 жыл бұрын

RX-8 is on my list, and there are always tons of broken ones for sale 🤔

@jaredmauldin8309 4 жыл бұрын

@@WatchJRGo Absolutely! A lot of demand for sorted examples

@A589C 4 жыл бұрын

@@WatchJRGo My dad gave me his 2004 which is in need of a good tune-up and probably other RX8 things. It'll be great video material!

@AOG_ETH 3 жыл бұрын

I could watch JR GO for hours hands down the best KZfaq channel ever.🇺🇲🇺🇲

@CarWizard 3 жыл бұрын

People!!! DONT buy a GM 3.6 V6!!!

@ryandickerson6395 3 жыл бұрын

The Wizard speaks Truth

@slasher9883 3 жыл бұрын

Finally, someone here that knows what they are talking about. Those motors are complete utter garbage no matter how often you change the oil.

@tomasnokechtesledger1786 3 жыл бұрын

Yep. Never will or Chrisley goats too.

@Walangord 3 жыл бұрын

Don't buy any GM actually

@NeedForSpeed45Racer 3 жыл бұрын

Hey its not a bad. Engine. With some mods it can be reliable

@JT-un7dc 4 жыл бұрын

That Milwaukee light is boss!

@artfisher1235 3 жыл бұрын

Great series of vids. Luckily, the timing chain replacement was so intuitive. Kindofa job you do without reading the instructions and it comes out great.

@edwardpate6128 3 жыл бұрын

Great set of videos! I'm sure it will help me when I go to do this on my 2012 Cadillac CTS Coupe!

@rhetericalpha 4 жыл бұрын

legit smile right after start up. Those success smiles!

@corsair3886 4 жыл бұрын

I love this series glad you saved a Camaro. Hope to see more if it and your older LT1 Camaro

@wendystarita7996 4 жыл бұрын

This is Brian. What a nightmare! And that huge timing chain cover. I'm glad I'm not doing it! Good work and thanks for sharing it.

@chrissuarez8300 3 жыл бұрын

Man I remember doing these all the time as a dealer tech. Gm tells you to set the left and primary chain then rotate the engine to do right chain. Cleaning everything was so satisfying to me

@jacobnicholas376 Жыл бұрын

Hello Sir!! I did see the melling video where they did the whole job in stage one timing with the cam special tools locked in, was wondering your thoughts why that is wrong?

@itsmephil2255 4 жыл бұрын

You are a brave man for doing those chains 👌

@vladimirmacko1481 3 жыл бұрын

this is waiting for me on my torrent 3.6. it's all disassembled already, it just needs my time... this is a very good refresh video for everything I've learned in theory so far. good channel! for cleaning the surface I used the white disc instead of green, 100 grit instead of 80. it takes a bit longer but I believe it's more friendly for aluminum.

@zigzagrz 4 жыл бұрын

always good to see Jonny make an appearance

@jeffeastman625 4 жыл бұрын

If O’Reilly’s isn’t sponsoring you, they should be. Milwaukee too. You give those companies a LOT of love! Great work on the Camaro, that chain set is NOT EASY!

@Purdue03b 4 жыл бұрын

I love that at 2:14 I can hear Hoovies Garage theme music in the background...the ultimate crossover channel.

@jasonp410 4 жыл бұрын

Awesome job! Would love to see you keep it along with your 4th gen Camaro. 🍻🍻

@luispalacios5132 4 жыл бұрын

I was waiting for another upload so I decided to watch all his old videos and as soon as I saw him post, I clicked on the video as fast as you doing a flip on Honda’s and selling them lol

@Gabe-ABNCW3 4 жыл бұрын

😉🍻

@tropmonky 4 жыл бұрын

Nice "Cake" Song reference.

@WatchJRGo 4 жыл бұрын

Love Cake 🎧

@MrWoodyBalto 4 жыл бұрын

I caught that title Intermediately! I have been binge watching 80's and 90's rock over the past couple of days. (not that I needed to be to get the reference) Maybe we will discover that Jerry was a race car driver.

@scooder33413 4 жыл бұрын

Take my thumbs up for Cake

@ddfred2u 4 жыл бұрын

@@MrWoodyBalto Jerry was a race car driver, and he had a lot of fans that were blue collar tweekers.

@towboatjeff 3 жыл бұрын

Started signing the dong when i seen that. Cake is one of my favorite bands.

@elrantraxplaza 3 жыл бұрын

Great work man love the details you give on point great videos

@DocMackGarage 4 жыл бұрын

Welldone JR. The car sounds better and the engine ticks nicely.

@theduke2398 4 жыл бұрын

I'm in love with the prowler.

@jean-marcandjoshua-petsjournal 4 жыл бұрын

Hoovie’s Garage intro in the background? Awesome!

@05milmachine90 4 жыл бұрын

Every time I see that guys super clean shop I think about cleaning mine.

@sufru6244 4 жыл бұрын

Love the vids bro keep up the good work

@hpelisr 4 жыл бұрын

Cleaning is the most important part, I would not consider the time to do as important. You are doing the work yourself.You have one chance to make right.

@uncommonsense5876 3 жыл бұрын

Have done timing chains on that engine. Cam lock is not actually needed if you assemble chains in proper order and timing marks are followed on chains/gears. The cam phasers actually have a proper static position that once you know where they go, its super easy to reassemble.

@richardfarmer6570 4 жыл бұрын

Nicely done JR.

@mikem5922 4 жыл бұрын

Watching you use that puller makes me think of the nightmare of Tyler’s BMW V8. What a difference!

@WN_Byers 3 жыл бұрын

Poor Car Ninja 🤣

@surfdude7575 4 жыл бұрын

Way to go JR! Awesome job. Looking forward to next video on header install. You gonna throw on a cat back exhaust as well?

@thecman26 4 жыл бұрын

"It's been a while since I've been John Rossed", Tyler Hoover 2020. Epic! I have a 2016 GMC Canyon with the V6, apparently Accel coils aren't available for it... 😭 Too bad! Those are sweet!

@kens97sto171 4 жыл бұрын

Good job guys, boy that thing made some hellacious noises when it first lit off. I think it may have been better to crank without fuel until oil pressure was built up first. Get all those new parts nice and lubricated before actually lighting it off

@michaelgraham2347 4 жыл бұрын

Time to drop the pan n change oil pump n screen

@kevins7093 4 жыл бұрын

Nicely done, good job!

@GIGABACHI 4 жыл бұрын

Great job ! Thanks for sharing. 👌🏻😊👍🏻

@doug960 4 жыл бұрын

My girlfriend's 2.4 Malibu snapped a timing guide at 60,000 miles. Car had been serviced somewhere between the "severe" and "normal" service schedules by me since it was purchased new. I used a Cloyes kit and fixed it. All new chains and guides. I had never attempted that kind of engine work before. Thousands of miles later, still good. I didn't learn my lesson and bought a used 2013 Camaro LFX. I hope I don't have to fix the timing system, but I know I could do it. Thanks, JR.

@muskokamike127 4 жыл бұрын

Post back if you have problems, I've heard CLoyes are only slightly better than Dorman and Dorman sucks......

@RichieRouge206 4 жыл бұрын

Done a great job John! So glad it started and ran so well but then I expected to if you did it lol

@GuitarsandDrones 3 жыл бұрын

JR and Tyler compliment each other’s channels awesome again guys. Good job on the chain, camera off two hand job ehh lol 😂

@noideaautomotive774 3 жыл бұрын

Good job man! This stuff is so inspirational. Also we have the same phone case.

@hacatan24 4 жыл бұрын

I had a 2007 GMC Acadia ..... Same 3.6 motor.... Mine was rattling so I took it in then they told me I needed a timing chain.... And on the Acadia or any SUV you have to pull out the motor or drop it from the bottom to do it.... It seems that the 3.6 always has timing issues.... But I am surprised that they got rid of the 3800 motor.... I think that border was the best motor that Pontiac ever push out..... It was a very reliable engine..

@AutoAuctionRebuilds 4 жыл бұрын

After watching, I bought that awesome Milwaukee MLW2125-21XC

@WatchJRGo 4 жыл бұрын

That light is perfect but my Home Depot is always out of stock... guess I should just order it. 💯

@jeffkersten5076 3 жыл бұрын

Hitman: Been an ass for long?

@gs3504 4 жыл бұрын

Nice going JR! Sucks how so many people don't change their oil regularly...

@LynxStarAuto Жыл бұрын

This video is what sold me on that BG engine cleaner. That engine was sludged ridiculously.

@1noneya10 4 жыл бұрын

Hats off to the car ninja for letting you use his workshop. I somehow don't think the car wizard would have let you use his space.

@muskokamike127 4 жыл бұрын

You can bet there's a "deal" going on, no way a shop would "let" someone tie up a bay for that long for free.

@keasbeydave 4 ай бұрын

Good job JR.

@wendellgreenidge3362 2 жыл бұрын

Amazing video fellas

@michaelcarter1963 4 жыл бұрын

Great job!! Hope you can finish the grey ghost (Rolls Royce) soon!!

@notrut 3 жыл бұрын

4:10 '....a whole bunch of compression ... Spark Plugs are out'

@grumpydumps2858 4 жыл бұрын

Yay good job man it looks great

@clonestarr3466 3 жыл бұрын

You make repairs look fun.

@Czechbound 4 жыл бұрын

"Smooth, quiet running engine". It sounds like a diesel !

@ducknorris233 4 жыл бұрын

Czechbound it sounded like three diesels before

@suburban404 4 жыл бұрын

No, sounds like a sewing machine.

@maxim430 4 жыл бұрын

Engines are often noisier on camera.

@matwilliams3299 4 жыл бұрын

The direct injection for the fuel ticks like that on all the new gm cars

@Cragified 4 жыл бұрын

@@maxim430 This is true. Built in sound balancing, shadowing, and response amplification often makes things louder then they are in person.

@setevcorker9104 4 жыл бұрын

That timing cover is ridiculous! No... actually it is ludicrous!

@WatchJRGo 4 жыл бұрын

Yeah, it was pain to clean too... scrubbed and scrubbed to get it right 😬

@muskokamike127 4 жыл бұрын

welcome to modern engines....the Ford 5.4 and 4.6 3V's are like that as well. Every double overhead cam engine is like that.

@kwinterburn 4 жыл бұрын

Seems wildly overcomplicated for what it has to do

@Njazmo 4 жыл бұрын

@@kwinterburn yeah those push rods are waaay simpler, and car is more safe because less horse power. ;)

@muskokamike127 4 жыл бұрын

@@kwinterburn THAT is the problem with modern auto engineers. They think they are smarter than they really are. Case in point: I think it is BMW who no longer put a dipstick in their engines to check oil level. Instead they use a complex sensor and the computer to monitor it. Another example: Ford's IWE system in 2004 to 2010 F150's. The engineers decided "hey, let's engage the 4wd ALL the time, and use engine vacuum to DISengage it" That's like having your bedroom light on ALL the time and you have to stand there and hold the switch OFF when you want to turn off the light. Brilliant? .......NO!

@marlenesanchez6370 4 жыл бұрын

O'Reilly's manager: hey guys keep an eye on Jr we need to get the parts that he needs. 🤔😆

@michaeljames9333 4 жыл бұрын

You just gave me hope for my darn enclave 😕

@JohnCurtisPiano 4 жыл бұрын

so glad you finally fixed your audio lol

@martinvelasquez9674 4 жыл бұрын

Good 👍 job, I really enjoyed this video.

@dontgetlippy9436 4 жыл бұрын

I like Johnny he seems like a cool guy hehe always smiling :)

@jimbobtheimpaler8403 4 жыл бұрын

Sounding awesome.

@spyderbuddy 3 жыл бұрын

I'm glad some one took the time to fix a Six'r

@mjjr1000 4 жыл бұрын

Love something good to watch to take my mind off toothache. Great timing 👍🏻👍🏻

@Gabe-ABNCW3 4 жыл бұрын

We’re here for you!😉🍻

@muskokamike127 4 жыл бұрын

I feel you, I needed some work done back in March on 2 teeth but the dentist closed due to Covid. 3 weeks ago I got an abscess in my upper right jaw, worst pain I've ever felt. I've shot framing nails through my hand, had knee surgery, nothing compared to that......call your dentist, get them to phone in a prescription for anti biotics and NSAIDs......

@mjjr1000 4 жыл бұрын

Richard Gmail mines possibly root jobbie in morning they say lol

@mjjr1000 4 жыл бұрын

Muskoka Mike good luck getting sorted out, luckily i got in on emergency appointment and referred to someone still practicing under strict conditions. On par with man flue lol

@mjjr1000 4 жыл бұрын

Gabe cheers Gabe 👍🏻👍🏻

@brandonsanders9674 4 жыл бұрын

Great job! 👍

@juanmespinoza65 2 жыл бұрын

GREAT JOB !

@roygunter3244 4 жыл бұрын

I almost bought a 2011 Buick Lacross with a 3.6 new in 2010. Instead I bought an Impala with a 3.5, the 3.6 was so much more powerful and for a few years I thought I should have gotten a car with a 3.6, boy I am glad I did not. I am an old man and fast is not really important to me but I drive cars until they are well worn the 3.5 isn't fast but boy it lasts forever.