The most common Macbook Air logic board failure

The most common Macbook Air logic board failure - how to fix.

Рет қаралды 231,369

4 жыл бұрын

Let's get Right to Repair passed! gofund.me/1cba2545
👉 If our videos have added revenue to your business, consider becoming a patron
🔵 Patreon / rossmanngroup
🔵 We fix Macbooks & offer free estimates. rossmanngroup.com
🔵 Send us your Macbook for repair! bit.ly/sendmacbook
🔵 We'll send you a box with a pre-paid shipping label for your repair! bit.ly/sendyourmacbook
🔵 We offer iPhone data recovery: bit.ly/2BDBX4G
🔵 We offer lab hard drive data recovery: bit.ly/labdatarecovery
👉 LEARN HOW TO DO THIS:
› In-person classes: bit.ly/classrg
› Beginner's guide: bit.ly/2k6uz84
› Support forum: $29/mo bit.ly/boardrepairforum
👉 Donate & post a message: bit.ly/postamessage
👉 Below we list tools & recording gear we use, repair guides to help you learn, online chip sources, & donation links:
👉 BlackBerry, Oreo, & Clinton the cat's wish list: www.amazon.com/hz/wishlist/ls...
👉 CHIPS & COMPONENTS:
› bit.ly/2jaAOXM
👉 Discord: tinyurl.com/rossmatrix
👉 TOOLS USED:
✓ Soldering Irons:
› Louis' Hakko station(no tweezers): amzn.to/2cKkMyO
› Paul's Hakko station(works with tweezers): amzn.to/2yMvWNy
› Micro Soldering Pencil: amzn.to/2d5MWUP
› Hot tweezers: amzn.to/2yMvZsZ
› Atten ST-862D hot air station: bit.ly/atten862
✓ CHEAP HAKKO ALTERNATIVES:
› TS100 soldering iron: amzn.to/2Gy1Fqz
› Recommended tips: TS-C4: amzn.to/33s3jpW TS-KU amzn.to/2QsKT36
✓ Preferred Soldering Tips
› Fine: amzn.to/2d5MgPn
› Flat: amzn.to/2JnsDBT
› GPU wicking: amzn.to/2w8chtB
› Micro soldering tip: amzn.to/2qUSFDh
✓ Microscopes:
› Microscope: amzn.to/2iLrE16
› Barlow lens: amzn.to/2yMKdKf
› LED light: amzn.to/2nzfPT2
› CHEAP alternative microscope: amzn.to/2rTlHbj
✓ Soldering/Repair Supplies:
› Solder: amzn.to/2cKkxUp
› Desoldering braid: bit.ly/2otflOX
› Flux: bit.ly/amtechflux
› Solder paste: bit.ly/amtechsolderpaste
› THICK insulated jumper wire: amzn.to/2rvtD0A
› THIN insulated jumper wire: amzn.to/2I47DQY
› Kapton tape: amzn.to/2yN0xuq
› Tweezers: amzn.to/2d5NBpi
› Blades: amzn.to/2ByWnvF
› Freeze Spray: amzn.to/2BySozw
› Conformal coating: bit.ly/greencoate
› Conformal coating curing pen: bit.ly/uvpen
✓ Diagnostic tools:
› USB amp meter: bit.ly/2B2Lu5W
› USB-C amp meter: bit.ly/usbcamp
› On-Screen multimeter: amzn.to/2jtgY9K
› Multimeter Probes: bit.ly/fineprobes
› CHEAP multimeter: amzn.to/2zjkg8U
› Bench PSU: CSI3005P bit.ly/benchsupply
› Phoneboard: phoneboard.co
› Boardview software: pldaniels.com/flexbv/
✓ Ultrasonic Cleaning:
› ALL MACBOOKS & CELLPHONES: Crest P1200H-45: amzn.to/2ITSQdw
› PRE-TOUCHBAR MACBOOKS & CELLPHONES: Crest P500H-45: amzn.to/2Qrnhf8
› CELLPHONES ONLY: Crest P230H-45: amzn.to/2QsckKG
› Branson EC cleaning fluid: amzn.to/2cKlBrp
✓ Desk supplies:
› Desk: amzn.to/2yMShdZ
› Chair: amzn.to/2LB8bUB
› Fume Extractor: amzn.to/2d5MGoD
› Work mat: amzn.to/2yMtlTR
› Outlets: amzn.to/2yNsZwo
› Gloves: amzn.to/2iUfumS
› Durable lightning cable: amzn.to/2yNHzUt
› Fine tipped snippers: amzn.to/2HGt4XB
✓ Screwdrivers:
› iPhone bottom screw: amzn.to/2yNwX8p
› Macbook bottom screw: amzn.to/2AKMdVb
› Torx T3: amzn.to/2zjtxxH
› Torx T5 amzn.to/2BLNDn4
› Torx T6 amzn.to/2B0XIfA
› Torx T8 amzn.to/2CpWp68
› Phillips #0: amzn.to/2AJaHhM
› Phillips #000: amzn.to/2yNqsCl
✓ RECORDING EQUIPMENT:
› Work cam: amzn.to/2QjHnt0
› Overhead cam: amzn.to/2eAH0oT
› Work mic: amzn.to/2WGIhzw
› Home mic: amzn.to/2xfampC
› Microscope camera: amzn.to/2icVQoG - mine is DISCONTINUED, closest one I can find.
› HDMI capture: amzn.to/2iyGcle
👉 Affiliate:
› Buying on eBay? Support us while you shop! www.rossmanngroup.com/ebay
› Rossmann Repair Group Inc is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com
👉 Leave a tip for us via cryptocurrency if we've helped you out:
› Credit card: bit.ly/postamessage
› Bitcoin: 1EaEv8DBeFfg6fE6BimEmvEFbYLkhpcvhj
› Bitcoin Cash: qzwtptwa8h0wjjawr5fsm0ku8kf40amgqgm6lx4jxh
› Dash: XwQpZuvMvU44JT7C7Uh6xHvkSadzJw9fMN
› Dogecoin: DKetsoCvwa2hF29ssgUA4Wz4hxT4kj3KLU
› Ethereum: 0x6f6870feb48f08388ee345cf0261e2f03d2fa310
› Ethereum classic: 0x671bfd61ba87edf6365c97cea33d66ba73645510
› Litecoin: LWnbTTAjojZQt68ihFJFgQq3cYHUsTcyd7
› Verge: DFumZ5sMhi3JktLQpsTVtV9xUt3zKDrcZV
› Zcash: t1Ko3FkphQYoQroQc8k2DVk4WKMAbmNR8PH
› Zcoin: a8QdvArHmdRYe1MjiqtP6jDNe6Z4JgnRKZ

Пікірлер: 309

@atticbear5098 4 жыл бұрын

Someone who sees a blown fuse and searches for WHY before replacing the fuse? Madness.

@ernestmccollum2397 4 жыл бұрын

Yes troubleshooting is a lost art. I have seen people put in foil to replace fuses and say its ok since it works.

@prjndigo 4 жыл бұрын

He'll also wait for the fuse to blow!

@CyberlightFG 4 жыл бұрын

How else could you find the fault?

@tasmedic 4 жыл бұрын

It's something which is discovered right at the beginning of the learning curve. Fuses are to protect everything between them and their supply voltage. If you don't look downstream and fix the fault, all you will do is blow another fuse. Or, worse, you'll blow more components downstream as well as the replacement fuse. I'm a bit surprised that black sheep didn't check that the short to earth had gone before he powered up. I guess he has seen this fault many times and knows that it's a single component fault.

@BillAnt 4 жыл бұрын

I've seen some "KZfaq mechanics" use a thin speaker coil wire to jumper the fuze. lol While it may work it's not the safest or most elegant thing t do. Also, I was wondering how come Louis never (or rarely) does any iPhone/Samsung/LG board repairs, which is usually the bulk of work most repair shop do?! Hmmmm

@eliminatorxx713xx 4 жыл бұрын

The first thing I think of when I see Louis Rossmann is *PPBUS underscore G3 Haa* I find my self repeating this phrase for no absolutely no reason. 🤷🏼‍♂️

@prjndigo 4 жыл бұрын

he says PP a lot. I wonder how long a video of just pieces of videos of him saying PP would be if it was all put together

@giantsfan7733 4 жыл бұрын

@@prjndigo It would be so long that you would definitely need to take a PP break.

@dutchdrone1249 4 жыл бұрын

I have absolutely no idea what Louis is talking about, but listening to him calms me. I said it before, Louis is the Bob Ross of board repair. 😊 I'm changing my band's name to PPBus and the Fluxxers ..

@mandc20022 4 жыл бұрын

*hot* not haa

@BillAnt 4 жыл бұрын

Those numbers just blow by my brain as meaningless mumbo-jumbo. lol Now if you said the power rail on a MacBook xxx model, well that's completely different. It's usually autistic people who remember such small details.

@ic531 4 жыл бұрын

I write software and don't fix hardware but I like Louis repair videos because I firmly believe that every problem has a root cause and you can work logically to find it and fix it. This and my job are the only few things in the world that still make sense.

@yxzaira5831 3 жыл бұрын

Having the worst day rn as my Macbook Air shut down this morning and wont turn on and I have a deadline this week with everything on my mac. After watching tons of vids today trying to fix my mac, I stumbled upon this vid even though I don’t have the tools or skills. Suchhh an entertaining vid you are so humble and funny! Made my day a bit.

@ernestmccollum2397 4 жыл бұрын

Moment of silence for all people uploading schematics, and bios files for us technicians.

@tetra1974 4 жыл бұрын

Many Bothans died to bring us this information.

@mrsem6670 4 жыл бұрын

Whoever you are; you da mvp

@jumbleofwords 4 жыл бұрын

And Epstein didnt kill himself

@rayshowalter6265 3 жыл бұрын

wish they would send the schematic and board view fairy for Mac Mini's

@uiscestudio 2 жыл бұрын

lol, you are transcendent

@maineiacnorth1243 4 жыл бұрын

"Yeah, get wrecked adblock" - That had me chuckling.

@garethfairclough8715 4 жыл бұрын

You and me both. That face was priceless.

@drawnsequence 4 жыл бұрын

Not me, that ad actually got me to download SponsorBlock. I like Louis but I HATE ads.

@congmp 4 жыл бұрын

ikr ! Like how did that happen ?!

@johang727 2 жыл бұрын

I have sponserblock lol

@Madhawa333 4 жыл бұрын

You make our days save our money. Show people the real path. Thank you mr rossman. Love from Japan.

@mchanslam8313 4 жыл бұрын

I love that you are so real even when you tell people that they can buy from other companies, you deserve a sub

@DeltreeZero 4 жыл бұрын

I am very happy to see your progress finding a new space, and also very happy to see your work in the right to repair movement, but I really love the board repair videos. Thanks for another great repair video! Congrats on your first million subs! O7

@raunokongas5136 Жыл бұрын

Very nice content and superior video and audio quality. Easy to learn, easy to watch. What you do is so huge to us and that right to repair thing also. We love you man!

@RealButcher 4 жыл бұрын

Great respect for your work Louis. Even in Holland you are an inspiration for a lot of people. Thanks man! And. Man, this is like Bob Ross... love to watch this and Louis his voice makes my brain very satisfied. AND we learn something.

@Apple-Bay 2 жыл бұрын

Thanks for all your hard work and for sharing all your knowledge !!!!

@SavageDarkness 4 жыл бұрын

imagine: Refusing to eat the bugs Refusing to live in a pod Accepting a $1,500 Apple repair bill.

@TheGrace020 4 жыл бұрын

Based and blackpilled.

@deebee390 4 жыл бұрын

Always educative, watching from Nairobi ,Kenya.

@c-styl3 4 жыл бұрын

Love your work! awsome videos all the time,very educational...from South Africa

@sebita85 3 жыл бұрын

amazing work! im just learning to rapair this boards.. ands this fantastic information!! Thanks so much!!

@jezeski2011 4 жыл бұрын

Another great and informative video; thank you.

@feenal1234 4 жыл бұрын

It symbolizes perseverance and hope amidst hardship ("' A tree grows in Brooklyn")

@DarthMaul41 4 жыл бұрын

You said the fuses are the most resilient components in MacBooks... Are you sure that's not a counterfeit? :) On a serious note your videos are very informative and nice to watch! Thank you!

@lochanpokharel 4 жыл бұрын

Thank you so much ..

@truthsyrup5764 3 жыл бұрын

thanks for supporting right to repair! techs without much soldering skill, (around here there are no solderers or motherboard testers), we only have part-swapping option and swapping out parts is cost prohibitive because of outrageous prices since they are all salvage because of apple's closely guarded part manufacture process, i presume

@lawsenimsfaoun 3 жыл бұрын

Every city deserves someone like you , to bad there is many scams and uneducated ppl on that field Thanks for that

@AnnaMae525 3 жыл бұрын

You got me at "Get Wrecked Ad-Block!" got me good because I use it

@DasDoubleD 4 жыл бұрын

Louis, I don't mind your shilling about yourself because you're honest and have honest advertising, straight up.

@KyleGP 5 ай бұрын

Years later, thank you again Rossmann.

@macdaddypimpping Жыл бұрын

Hey Louis, I just follow your method to check my 2011 MacBook Air A1369 and found out one of the fuse and a (A1 V7e) capacitor was burned, do you sell these two parts?

@Tuck-Shop 4 жыл бұрын

I just lost it at the "Get rekt adblock"

@TheMetalMag 3 жыл бұрын

Excellent intro, cool thx great job

@vanannavarasan4522 4 жыл бұрын

To repair electronic boards, one needs to understand basic electronic hardware, i.e., capacitors, semiconductor chip and the knowledge how to use and read the parameters shown by these equipments. Also, the knowledge of reading and interpreting schematic diagrams of the circuits boards is also necessary, Apart from that one needs to have an investigative drive to explore the possible issues that could have caused the problems int he board. This will be possible if you have a good amount of experience in doing these activities by trial and error.

@tasmedic 4 жыл бұрын

Among many other things you don't even mention, you'll need a good brain, and at LEAST 1000 hours experience in one corner of the market, say macbooks or TV's, to have any chance of making a living at it. Trial and error will simply take too long to be of any use in a commercial setting. Also, sharp eyes and a good sense of smell, often those 2 things will make everything else irrelevant by bringing you immediately to the failed component.

@TheSushiPlant 4 жыл бұрын

tasmedic what about good sense of smell?

@macintoshimann9892 2 жыл бұрын

Actually got fired for the only time in my life from an electronics factory... really a shame because they were starting to teach me how to do rework on SMT compnents like you showed in this video which I found tons of fun!

@EmptyTome 4 жыл бұрын

This macbook is defective, the fuse blew.

@windhelmguard5295 4 жыл бұрын

it's not a macbook, blowing the fuse turned it into a PC

@flamingkillermc2806 4 жыл бұрын

Windhelm Guard 😂

@SovereignKnight74 4 жыл бұрын

Great job! /subscribed

@thenoeochoa 2 жыл бұрын

amazing software bro

@mpuppet1975 4 жыл бұрын

I love RapidCool® technology.

@Finnyspinnys 2 жыл бұрын

Same problem here... all fixed! Cheers Louis, you're a champ!

@macdaddypimpping Жыл бұрын

Where did you get the fuse?

@Finnyspinnys Жыл бұрын

@@macdaddypimpping From a scrap board used for spares…

@macdaddypimpping Жыл бұрын

@@Finnyspinnys How much was the board? Most of them I see on eBay it says non-working

@nicholasfrancis9303 4 жыл бұрын

Hi Louis what’s a safe temperature to remove board components without damaging the board or nearby components? 🇹🇹

@haustierone 4 жыл бұрын

man, ure my tech Bob Ross greetings from germany

@kimosullivan6929 2 жыл бұрын

What temperature do you normally run your reflow gun at for this type of SMD removal?

@williamhanson8004 4 жыл бұрын

It's amazing - the fuse actually did what it was supposed to.

@one_step_sideways 2 жыл бұрын

Must've been an oversight by Apple Think Different™® department

@sergre1505 4 жыл бұрын

.. i'm spinning .. nice work!

@mikeak7331 4 жыл бұрын

Yes

@A.S.M.S 4 жыл бұрын

What’s going on boss, big fan of yalls work over there. I am a new KZfaqr that has ran into the same problem just yesterday as I was naming my video to post on my channel. I was wandering how much you guys would charge to diagnose and fix the problem.

@keaelectronic5275 Жыл бұрын

Good brother

@Pops180 4 жыл бұрын

You will never see a tantalum capacitor in any piece of automotive electronics because of the ways in which they fail. Apple seems to like them quite a bit for some reason.

@3nigma.3nc 3 жыл бұрын

They have pros and cons like anything.

@Wexexx 2 жыл бұрын

@@3nigma.3nc Pros: They break stuff, cons(pros for Apple): Makes consumer buy new items which break.

@shimondoodkin 3 жыл бұрын

do you have a theory why capacitors fail after liquid? my first guess is like two caps connect together by liquid and over voltage a third cap.

@charlize1478 4 жыл бұрын

Who else has a broken MacBook but doesn’t have a single clue of what he’s saying

@ErictheRedCantona 3 жыл бұрын

I got the bit where he was silent

@3nigma.3nc 3 жыл бұрын

Looks like you should send it to him then so he can worry about fixing it.

@whoisharo4689 3 жыл бұрын

yup

@andrewstoll4548 4 жыл бұрын

A Tree Grows in Brooklyn. I do believe it's a book. It was in several looney toon cartoons

@n4_ku 4 жыл бұрын

Wish you would zoom in more when you are testing components.

@backposedtraveller9886 2 жыл бұрын

THANKYOU FOR THIS VIDEO. I HAVE ONE MORE QUERY THAT WHERE CAN I DOWNLOAD THESE DIAGRAMS OF MOTHERBOARD. THANKS IN ADVANCE

@rebarius 4 жыл бұрын

Do you also upgrade SSDs on MacBooks Pro 2017 (A1707)? I just found new logic boards on ebay, but they cost a tone

@fernandoturkovich1178 3 жыл бұрын

hi Louis and friends , what average of tolerance do u use in lines measurement , for exaple one 1,5v optimal value vs 1,36v do you consider that one like good or not ?

@rayshowalter6265 3 жыл бұрын

Is it always that Cap or could it be one of the others in that area? I have a blown fuse but the caps look fine. I removed the same one you pulled and checked if it was shorted and it isn't.

@ElAndresRodriguez 3 жыл бұрын

How much would something like this cost or do I have to ship it in first?

@adorunderscorebutch 4 жыл бұрын

My 2015 Air died after less than 3 years of use. The Apple service center would charge eye watering prices for it. A non-apple center just told me it had a "dead board" and I had to buy a new board which would cost almost the same as a new one, and that was the only other repair center in my area that had the chops to repair it. I was so dejected, it's now gathering dust in a corner. FML.

@Nija_fans 2 жыл бұрын

Hello, nice work and I really love your videos. I have a 2014 11” MacBook which I have been using since 2014 till date but a month back it ran out battery and it wouldn’t turn on so I tried everything including the disconnecting abs connecting the battery back until I did the smc reset which actually worked and it’s been working fine till 8 days back. The system was fully charged and I decided to shut it down because the airdrop was acting up. Ever since I shut it down it has refused to turn on or charge ( no light on MagSafe), tried different working chargers but it wouldn’t work on my system. Tried the smc reset, disconnecting the battery, touch pad flex and even removing the sscid and replacing back but nothing is happening. I am currently in Nigeria where there is no apple store and am scared to give it to some random repair guy cause they might cause more damage to the system. Can you pls help give some clues as far what could cause the system to breakdown like this. And what hardwares or chips fault could result go this. Thanks for your anticipated response Olivia

@ophello 4 жыл бұрын

Hey Louis! How much did this repair cost them?

@niteshnaik2946 4 жыл бұрын

Ur welcome

@jolsondacosta2017 4 жыл бұрын

Hey Louis , where would I find these capacitors In india. not always I will find donors for various components

@theKashConnoisseur 4 жыл бұрын

1:55 And here we see Louis offering a moment of silent prayer to the Patron Saint of Board Repair.... Paul Daniels.

@cort3933 4 жыл бұрын

Would you buy a surface pro 1796 with all accessories, i7 8 gb ram 256 ssd for 400? Is that a good deal?

@terrypen 4 жыл бұрын

1:45 @Louis, you need some serious help! haha

@parekoykulet9667 2 жыл бұрын

Sir i just want to asked i have a 2012 macbook air A1466 i cant figure out whats wrong.. it turns on but super slow to the point it is unusable

@rexroysequeira1291 3 жыл бұрын

Hi i have a macbook air which is not rueing on no matter wt i have to seevice centre they say that the power managment cheap is dead n dat its not available and need to replace the entire mother board can you tell me if there is a way i cn get it working

@GibusGang 4 жыл бұрын

most common failure: buying an apple product

@BillAnt 4 жыл бұрын

Finally, someone who gets it. ;D

@centralelectronica7534 4 жыл бұрын

hahahahhahahhahahahhahahhaha i Died with this one

@ophello 4 жыл бұрын

So tired of computer elitism. You’re just a child. All computers are pretty much the same, except that Macs run OSX, or Linux, or windows. You can run anything on it. That’s one reason why it’s a better choice than a PC, and it’s the right choice for a lot of people. Get over it.

@gouletpalexandre 4 жыл бұрын

@@ophello I think it's pretty ironic that you are accusing him of being elitist and that you are being elitist by saying that Macs are better than anything else...

@iWinnipeg 4 жыл бұрын

Ooooh, so edgy! You must be proud of coming up with that one. Hurr durr.

@Billblom 4 жыл бұрын

A tree grows in Brooklyn....wasn't that a song back around 1900?

@teambmmedia7919 2 жыл бұрын

After changing hard drive Mac Mini USB drive stop working. what could be the issues? & how can I solve it, please?

@A.S.M.S 4 жыл бұрын

I currently have a 2011 Mack book air that screen and key bored went dark and beeps 3 times consecutively.

@ro4ers 4 жыл бұрын

I'm kinda new to this channel and have only soldered larger items, e.g. headphone wires etc, so I'm a bit miffed. What does he pour over the board before soldering? I guess it might be liquid flux, but I'm a bit short on how it works.

@jamesellis5445 4 жыл бұрын

ro4ers in answer to your question there... 1. A keen eye. 2. An attention to detail. 3. A whole lot of love. 4. And as you stated, Liquid flux....see 15:19

@jeffhung8896 Жыл бұрын

How much is the fuse for a 2011 MacBook Air and a Capacitor "A1 V7"?

@nothinglastsforever0000 2 жыл бұрын

How do you learn about all this as a complete beginner with no experience in engineering?

@jayade5481 4 жыл бұрын

Mine is macbook late 2011,logic board corosive, battery shows repalce now, screen look bad, should i buy new or i can fix it specially the logic board...

@Luminousplayer 4 жыл бұрын

im more surprised that the fuse actually blew

@irukhan07 4 жыл бұрын

"I have employees to feed"...lol

@yahnsolo 4 жыл бұрын

Another damn shorted capacitor..... What the hell Apple make to those caps for them to commit suicide by Puuuffffff... lol Another successful repair hehe. Indeed, I DO learn something every time I watch your videos! Thanks for that

@skildude 4 жыл бұрын

A tree grows in Brooklyn is a book and a movie. The meaning of which is that families "trees" are growing in Brooklyn

@GPSJayDog22 4 жыл бұрын

Number 1. Thank you for sharing. I would like to know if you clean the board after you repair it to get all the flux, yukky hairs, bugs and all the other gross things I see on the boards you repair. I often think you should be waring some kind of contamination suit while you work on them. Way to yukky for me. I watched a friend of mine who owns a Motorola repair facility that works on California Highway Patrol gear actually using a cleaner and a small brush to clean the boards. Please keep in mind this was twenty years ago before surface mounted components which I figure were more robust and could take the beating. Thank you for your work. Jay

@pansepot1490 4 жыл бұрын

Yes, he cleans the boards after repair. Uses a kind of steamer/ultrasonic machine or something. I haven’t a clue because it’s not my job but he talks about it in other videos and I think he sells the cleaning machines on his website.

@GPSJayDog22 4 жыл бұрын

@@pansepot1490 Thank you :-)

@DrFiero 7 ай бұрын

When this video first came out, I'd take a shot every time he said PPBUS. The hospital said I'd never make it. Just got out. :D

@manasbhatt007 3 жыл бұрын

Hey I m in huge problem .. while replacing the dc/power board on my logic board , I accidentally broke the port/stand on which the right speaker cable rests(pried it out). The right speaker doesn't function now and since it's embedded with the logic board I am afraid if there is any hack to get it to work or not; I can't afford to buy a logic board at the moment. Can you pls suggest me some solution. Can this port b fixed somehow? 😟 Model :mid 2014 a1398

@richystocles 4 жыл бұрын

"get rect ad block" Just for that, I rewinded and watched the sponsor part 👍

@superdau 4 жыл бұрын

How come the fuse blew? I thought they are the last thing to go in a macbook?

@jonajell5590 Жыл бұрын

you are the bob ross of computer mechanics!

@ranzali5564 4 жыл бұрын

So what (Win10) laptop do you recommend?

@dennisprah985 4 жыл бұрын

Hi please do you have a contact point in Ghana, i really want to get my macbook board fixed

@byjev7881 4 жыл бұрын

That moment of silence seems incredibly challenging

@jasoncornell2474 4 жыл бұрын

LMAO... "Get rekt AdBlock". Too damn funny.

@DumahBrazorf 4 жыл бұрын

"The Dark Side of the Fuse", written, produced, directed, filmed and interpreted by Luigi Rossmann as himself.

@W.A.REED.The.Fourth 2 жыл бұрын

Yeah, I can see it! Paul and Louis as the uber jedi and apple as the sith lords...

@Raytechable 3 жыл бұрын

do u really recommend flexbv and why

@truthsyrup5764 3 жыл бұрын

a2179 won't pass mac logo... progress meter fills up then hangs... google isn't proving much use, nor the apple care line. 2 reps said they couldn't pinpoint issue and suggested apple store 200km away so that's where i'm going looks like. any ideas?

@tomlearman7704 2 жыл бұрын

Where can I buy the cap 4R7 and diode

@wazulhaque8896 3 жыл бұрын

What to do if +8 volte missing on charging qual and motherboard is not get on

@BlueRidgeGamerz 2 жыл бұрын

Where can I purchase F7140 replacements thanks

@danielszulc9574 3 жыл бұрын

Hey I replaced motherboard on my air and cannot instal Catalina, should I install mojave and then catalina? I suspect old firmware on new logic board since I had to change date from 2015 to 2021 using terminal, not sure how to upgrade firmware... or is it the real reason ;p

@user-jo8yx2xd9l 5 ай бұрын

How you did that? Iam heating since 1h, cant get ic cap up, now 1000$ board is really dead, all nearby caps are gone

@Juniorduke1 3 жыл бұрын

I want to buy this part is there anywhere I can get it

@MrDarkbluewater 4 жыл бұрын

Does anyone know how Louis gets rid of that sticky mess that gets left behind by the flux? I have seen him use a qtip, but what chemical does he use on them?

@shifty2755 4 жыл бұрын

Isopropyl alcohol. Evaporates quickly.

@mif2010a 4 жыл бұрын

“Get rekt Adblock”

@theKashConnoisseur 4 жыл бұрын

Too bad it's still no match for Fast Forward ;)

@niina83 4 жыл бұрын

@@theKashConnoisseur or "Sponsorblock" :P

@Phynellius 4 жыл бұрын

was a funny thing to come out of an ad into

@paulcarmi8130 4 жыл бұрын

@@niina83 is that a real thing??

@niina83 4 жыл бұрын

@@paulcarmi8130 Yes, type it into google

@jezeski2011 4 жыл бұрын

How to fix (if you don't have the tools)? Send it to: Rossmann Repair | 186 First Ave | New York | NY 10009

@CaseyKCRichards 4 жыл бұрын

I spilled coffee on my new Mac book air 2018 , I had it only one month. I handed in x 2 Nd they could not fix it because they are scammers . Right now when I turn on the computer it flashes like there’s something wrong with the Track Pad, mouse . If you can fix it : my email : caseykcrichards@gmail.com I did take the mother board it myself ,

@johnnybegood8049 4 жыл бұрын

An easy one

@TAILSORANGEs 4 жыл бұрын

Louis, Plug your PPBUS into Apple's PPBUS and shoot 50 volts into their "CPU"

@seven9766 4 жыл бұрын

unfortunately, that cpu is made from superconducting transparent aluminium. 50 volts wont hurt it... a bunch of bullshit (should be obvious but still)...

@TAILSORANGEs 4 жыл бұрын

@@seven9766 There's something called "figuratively speaking"