Those 3 minutes were the fault of having to explain to us what you were doing and why. It's been studied/proven, that multitasking slows us down. I have a door I have wanted to have replaced. I think you just gave me the confidence to do it myself. Thank you, from an old woman.

I like how you tacked the shims up first... I always find myself wrestling the door and shimming at the same time. Good stuff 👍🏼

I haven't heard anyone say water pump pliers. My dad which is gone now always said it. I think you and I are the only ones that k ow what that means. I'm a retired custom cabinet maker, trimmer, contractor. I love it water pump pliers. In my family it was Channel Locks. Just watching KZfaq and your video came up. Keep up the good work. Ed.

13 minutes is very respectable, particularly as you were explaining everything as you went. If I were doing that, it would take me a weekend. Part of that time bill would be explaining everything to my better half. She usually wants a detailed explanation about what’s happening, most commonly after I’ve applied 5 minute glue but before things have gone together.

A couple of suggestions. I always pre-drill with a countersink bit any screws I put through. The chance of cracking is too high (especially with MDF jambs) even with skinny screws, and I prefer not to risk bridging and to have the screw head guaranteed be below the surface without bulging up the surface. (for when it comes time to finish) I try to have the shims from both sides so I don't create an angle that when the screw goes in could cause the jamb to pull in a bit on the unsupported side. You may notice at the bottom edge below the bottom hinge the jamb curls in a bit towards the door (9/10 prehung doors seem to suffer from this) I'll do a predrill and countersink about one inch from the bottom and put a screw there. The screw allows fine tuning to be able to pull in that bottom leg so that the gap is consistent top to bottom)

For hollow core doors I like to case one side & set the door by plumbing at the hinges & nailing through the casing into the framing. This is enough for a good initial set on a hollow core door & allows the casing to act as a depth stop. It also makes it really easy to check your gaps & make adjustments if needed. Once the door is initially set, you can open the door and go to the uncased side to add shims before nailing the jambs & casing the other side.

I literally can’t wait to try this, I’m heading to the unit I’m flipping now to give it a go. Please show more it’s giving me the confidence to go tackle my career of carpentry.

your doing it the right way. looking good. i have been a carpenter for 48 years

You are a solid 2 mins faster than this old timer 😂. Definitely picked up a few tips on this video. Thank you sir.

When I was building homes we had a pretty slick method. You put the trim one side. Put the door in the hole and (one guy on each side of the door) pushed it all the way to the left and marked, pushed to opposite side and marked. Then it's easy to center the door in the hole based on your marks. You plumb and shoot the trim on the hinge side. Level the top, plumb the other side and shoot away. Guy on the other side puts the shims in. We had it down to a science and knocked all the doors out quick. Very fast and solid install

Great work, so many so-called carpenters mess up the hanging of a prehung door set. They approach it as if it's a standard unit, stripping it down and defeating the purpose of the handiness of prehung. Weel done. Nicely demonstrated, cheers

Great process and explanation but after doing it for over 40 years, I found and easy way to hang the door on a wall that is not plumb. You centered the door frame flush with the drywall by starting at the top but if the wall is off plumb by more than 1/4 of an inch, the door frame is going to be 1/4 inch out on 1 side and 1/4 indented on the other side

REALLY good info, like in my trade, its the little tips and tricks passed down/around, combined with EXPERIENCE of doing makes a PRO

Framer did a good job sizing that opening for the door. Makes door install much easier and faster.

Ya' had me at Hangin' with Bob Ross. Great channel. I've used a number of your suggestions.

Followed this tutorial to a tee yesterday on a coat closet door and results were perfect, thank you! Took me 45 min tho and that included watching college basketball on tv throughout.

Great job - instead of the headless screw I always got a 3" screw and used it in place of one of the hinge screws. Then again, I usually was putting up nickel hinges lol

You solve that problem by centering the door frame at mid height and then plumb it. It will automatically split the difference. Thank you and great videos

I like to put the shims in from both sides to avoid twisting of the frame. But I love the idea of stapling up the shims first. It definitely makes it a quicker install.

That's all fine and dandy for a newly framed opening. Now do it in a 100 year old house where the walls is different thicknesses top to bottom due to lathe & plaster, out of plumb and out of square .

Nice video, I like to tack two boards across the opening to keep the door flush and keep it from falling through, makes is much easier.

I was just thinking.... I remember doing it in under 10, and then you said it! And then that same realization hit me... that was 20 years ago!

Nicely done! I like to add a shim above and below the strike plate for a little extra rigidity.

We just used EXPR Premium Door install kit to replace an exterior basement door. It was the fastest install we've ever done. These brackets attach to the door jam and take the place of shims. they are easy to bend, and have a slotted hole to allow adjustments for plumb and level. I am ordering more kits to install the rest of the doors on our major remodel.

Not fair! You have tools and expertise. Happy New Year!

Great hustle, awesome tips, thanks for sharing!

Those are some extremely secured shims

I use a rolling cart around jobs like these , saves bending over a thousand times ..great video thanks. I learned from it

Just came across your channel Great video next time case the in swing of the door shot trim to wall and go back and shim and you only have to trim one side up everyone one has different ways I only install solid jams no split jam doors Great video again

I'm a rough carpenter by trade but on the few hundred or so doors I've set, I've noticed that OFTEN, the stop moulding isn't perfectly set. So I'd end up chasing my tail trying to get the door to close plumb against the stop. I now check the stop mould reveal before moving the whole jamb to flush up a door.

Srsly!? That was awesome, dude!! If that isn't good enough for somebody you really don't need that person in your life! Haha. Thanks for all the great vids!

Hey your videos are awesome. Love you presentation style, very clear. Brilliant stuff.

Nice work, I have done doors infrequently enough that I end up just hacking them into place with lots of banging and wiggling. Nest time, I am going to watch this video the night before, great clinic. Remember though, go slow like a pro. Could tell you were trying to hurry, and you weren't as efficient. I work hard on that too. Thanks!

Great job man. Guessing you would have hit your mark for time if the old haste makes for waste didn't kick in. We all perform so much better when we can focus on the job at hand and not an eye over the shoulder.

Several things: Start by making a 14" 'Eye shaped' block. 1 1/2" x 1 1/2" with a 6 1/2" taper both sides(1" flat spot on centre). Tapered to 1/4" one side(for finished floors) and 5/8" the other(for unfinished floors). Sand round the taper as to make a rocking block that performs smoothly. leave the two flat faces. This tool is now your DOOR PEDAL. Installation: Do all pre-measurements/plumb checks. Pre-stand your door in place on SPACER. Remove strike lock screw. Open door 90*. Place DOOR PEDAL under door ON CENTER. Angle door into finished position. While using the DOOR PEDAL(you will get the hang of it right quick). Set shims and screw upper HINGE SIDE. Hold level on inside of door to check for PLUMB, then check jamb for plumb. Set shims and screw bottom. Then do the same process. But check your door swing as well. It looked like YOUR INSTALL had a lazy close. I could be wrong. But would suspect by the way you shimmed, you have a trapezoidal/rhombic door opening. Proper shimming would solve this. As well, over time, the slight twist will effect the reveal. Especially on bathroom doors. the difference in a 10 year install and a 40 year install. DO NOT: Kick the door. You have a hammer and a block. Lean door against finished wall. LEAVE IT UNTIL YOU USE IT. Pre-nail shims. WASTE/REDUNDANT. Post-nail door. WASTE/REDUNDANT. Waste time dragging around a compressor from floor to floor. adding time-used to tools you don't need. WASTE. All presents you as more professional. Aaaaaand the painter won't hate you. Probably falls on deaf ears, but good luck. Tyler- Finish/Deficiency carpenter 20 years.

This is fine altogether but as a suggestion...before anything else, remove the door completely from the jamb. Then proceed with plumbing the hinge side after checking floor level and making adjustment to height. Next, use 2 foot level to check upper jamp and secure it to the header opening. Lastly, measure the opening of the jamb at the very top and work your way down the lock set side of the jamb ensuring the same width of the opening. Finally, reinstall door to jamb. This is how I've hanged doors for many years and it's always a perfect install while I never have to fight the weight or bulk of the door itself.

That's right... we can ALWAYS LEARN and get better...!!!

Very impressive. I've fancied myself a "door guy" for years, but am always looking for tips. Your method here is pretty bare bones and efficient. Shooting on the shims is genius. My first worry is the "walking legs" problem. When left and right R.O. trimmers are not in the same plane. I guess that is checked first, but I didn't see you do that. Second: do you shim behind the hinge for running a 3 inch screw through hinge into framing? I've watched most all of your videos, and can't remember if you do or not. Anyhoo...I like your content. I get something from most every video you do. Even if it's a little lighthearted fun, I appreciate it.

I usually pin a brace across the door frame to keep it square, and unpin prior to fixing to the jambs. At least you can keep it in place whilst shims are being located.

I do pretty much the exact same install. Only I put a 3in hinge color screw in the middle hole of each hinge.

The only places I would differ is centering the hinge jam to the drywall instead of plumb. I'm a little OCD about doors swinging (even a little) under their own weight. I'd rather trim a jam if it's proud of the drywall if needed or cut jam extensions if they're to shy. But I know this isn't optimal for production work. The other thing I would do differently is the 3" screw. I shim the top right at the center screw of the top hinge and use a 3" screw the same color as the hardware through the center screw hole.

Enjoyable to watch you. Lotta good tips. BTW, It's been 3 weeks since you did this. Are you and the Fam OK? Hope to see you soon.

At first i thought this was a comedy video when you started to put the door in backwards and then it fell out of the opening. Good redemption.

Great video. I have struggled hanging doors in the past.

Actually THE fastest way is to hire the Funny Carpenter

Luv the real-time action. You should do some more of these :)

can hear your heartbeat start to pick up at the 7:40ish minute mark, thought I was going crazy hahah

Good video. In particular I like the trick of using the level and preinstalling the shims on one side. You might want to consider doing a more thorough version that explains each step in more detail. If I hadn't watched a bunch of other door install videos and done it myself (once, with a lot of fussing and fiddling with shims :-)) I'd be pretty lost watching this.

Pretty close to the way I use to do it but I never used a level b/c all I did was replacement. Had to balance between the paint lines. I would prep all the doors, bottom blocks and the latch keeper. Then put the door in the hole and pop a 16ga. up through the head. That holds it. Shim below the bottom hinge and shoot below it. That way you can pull the shim out if needed. Next it was a 16ga. with pressure @ the top hinge to suck it over. I would shim at the head on both sides, strong enough to hold it in place, balanced between the paint lines. The latch leg could go up or down, as could the hinge leg. Closing the door and temping the bottom of the latch leg. Paint line check... margin @ the head check. Margin check @ the top hinge to latch. Margin check @ the bottom hinge to latch leg. Check door hitting solid on the latch jamb. Nail the head and bottom shims. Always shim behind the bottom hinge shim. That's where the compression happens. Leave the top hinge free. If needed you can come back with a 2 1/2'' hinge screw. Then shim and nail at the latch. Did that for about 20 years. Never went to Door School. That's what worked for me. Got it down to 7 to 8 minutes after the prep. So that equal to your 10 minutes. But I was 47 when I started and gave it up around 67. Keep it up young man ;)

It would probably take me three hours since I would be constantly second guessing every little thing that I did throughout the process haha.

Great tips. Along the way that is how I have learned to do it.

OMG you made that look so easy took me 3 hours to get one exactly square and working. Ugh

Very impressive! Especially in 1.5x speed haha... You've clearly done a few of these ;)

There's another KZfaqr out there who once said: he drives a Bentley, but could he hang a door?

Good job👍 Speed and the right way is the best.

"use the ol' boot hammer" 😂😂😂

In my country we use mounting screws that secures the farme in all direction and i put only two diagonal shims in a door, unless its very heavy

Nail your trim on one side B4 u put the door in it keeps everything strait level and plumb good job though a lot of people will definity not make 10 minz

Under 15 mins and you’ve got a door’ I’ve been “trying” to cut and install door casing for 2 weeks now’ procrastination is powerful

I clicked on this video thinking it was the handyman’s channel!!!

You somehow magically time your videos right when I need to do same project! What/where do you recommend for buying a prehung door? My house was built in the mid 90s and we have a glass panel door at the top of our basement stairs that opens down to the stairs and I want to replace it with one that opens/closes to code so my infant twins that are now all over the place don't somehow push the door open and tumble down the stairs. I love you content and thank you for past responses!

On one side of opening put few straps across opening them door frame can sit against that especially useful when installing heavier doors

Hey Bos, hope you’re keeping well! Still haven’t see you in person, but I try to wear my Funny Carpenter” t-shirt every time I’m out your way, just in case!

👍👍👍 Wishing a happy healthy and prosperous New Year to you and your family.

Why not have chims on opposite side so hanging side can have more support against stud. I'm legit wondering cause I don't know

Camera 1 could have been at a better angle and a bit closer..... would helped a lot better seeing what exactly what you were doing and checking . Thanks for the video though! I will take what I can from it and im hopes when time has come to do the doors I wont f it up! Lol

I've seen guys do it with the arcs/casing fixed on one side I've done it myself once then once it's square depending on the gap between the studs and the frame squirt some foam adhesive in then pop on your other casing/arc

is it just me who would like to see the funniest way to hang a door? :)

Buddy fast cap make counter sink drill bit? Hang your door then remove that hinge just the jam side and counter sink a 3” screw right behind that hinge ! Now it’s hidden & your door will not move when painters come and take off the door paint it and throw it back on!

Timely video, I'm celebrating NYE by replacing 6 doors in my house

Be sure to see the Funny Carpenters other video. It’s less rushed and more explained. Thanks for the tips!

Would love to see an exterior door that is all sorts of out and replacing the jamb and sill plate while keeping the same door.

Very nice. I would love to see your next video with a closer look of what you're doing. May I suggest a camera on top of your hat. Thanks you!

Great video !!! thanks and happy New Year !!!!

Use Quick Door Hangers and will cut your time in half guaranteed or even less. Cost like around $4 for 6 fittings at Home Depot. No shimming needed, just super fast and accurate installation

Great job. Faster than me for sure.

Also keep in mind if the house experiences extreme hot, and cold spells due to the weather changes, and your hanging the doors in the cold (house isnt heated in the fall/winter) then leave bigger reveals as the wood will expanded ehen it gets heated back up.

Great informational video. Thanks Don

Make sure when you remove the shims you don't chip the jambs, but your kicking the door!

Up here in Canada, we don't have the braces on the bottom. They are usually encased in a cardboard wrap

Happy New Year, Funny!

I put blocks under the jambs. I usually don’t nail shims to the rough open bc sometimes the opening is 1.5” to wide which leaves for a great day of hacking crap together and telling my co worker how he should only be allowed to screw lightbulbs in.

Use a door stud tool; ez hang, 3.5” pieces of plywood! Never ever shim behind hinges they move over time however they just don’t call u back! Hang dood chk before & after for cross leg! Hang and remove top hinge jam side place a 3” screw behind hinge so when painters remove the door does not! That’s a pre hung! I use very few of those huge long hinges I make 8” ones!

Your breathing like you just ran a 3000 mile marathon!!

Good jobs

Thank you... Great video. Will help me out

"plumb" is up and down. "Level" is horizontal. Folks still continue to get this wrong. Just sayin...

Man, you got to try them Essve Programa frame screws! No need to mess with shims. 😉

Great video

Much respect

The Funny Carpenter??? More like The Sexy Carpenter!!! 😊 IDK why...This guy is just too cute! 😁😘 Did you move into the new house?

Get yourself a jamb master eh

This was great it gives me confidence that I can hang my own doors

1983 I started trim carpentry work on apartment complexes. Each apt had 13 doors. I made one dollar per door that I hung. Lol….

Psshh ..... 13 minutes 17 seconds. I could do it in 13 flat.... Just kidding. Another great video! Thanks.

They make clips that screw to jambs and then to studs. Those make install a lot faster and a lot less awkward.

Verticle is called plumb where I am from. Six nails in a shim?

Try nailing the casing to the frame first then hang it

Made the mistake of building my own door frame for an old door. It works and is plumb, but for some reason it binds just slightly when you are about to close. It does close okay, I thought after a year it would sow me through wear what's binding, but no luck.

Thanks!