Hello from San Antonio, TEXAS! Depending I guess on the application as to how much force this gear is taking I would have pressed/heated it in using an interference fit followed up by a nice roll pin but that is me.

I really respect the way you work to design damaged items to be rebuilt. I'm a mechanic who finds it difficult to find pineapple-shaped gear and has a difficult structure

These guy's are fabulous fabricators

Amazing to watch excellent work it's good to see how parts use to be made much respect.

Undoubtedly, master machinist. Thanks

Похоже, парнишка, уже один глаз повредил. Но всё равно работает без очков

Well this is a turn up for the books. Keith Rucker has a go at cutting helical gears, having to make up some elaborate set ups, and takes for ages. Never mind the hours and hours spent reading up on it in the machinists handbook and others, and all the calcs to get the job done. Abom79 wouldn't even go there, too many calcs and trig for him, lol. Whereas these guys have the right machine for the job and get it done in no time.

В этом адском конвеере я упустил из вида термиста. 😄

You guys are very talented, good luck

Excelente maquinista , aprendo mucho

Ele deixou a engrenagem folgada no eixo ❗, e posteriormente soldado com solda amarela ❗, condeno esse trabalho , a engrenagem deveria ser argolada a quente , e a solda com o eletrodo 7018.

Excelente trabajo

👍👍👏👏

Creative video, thanks :)

Te pasaste de la medida , el piñón está flojo. Te pasa por trabajar alocadamente, sin micrómetros. Mejor era con chaveta en el eje y piñón y el ajuste de prensa.

Good Job 👍

Prindapan pancen expert... 👍👍👍

Meu sonho é comprar um torno 😃😃😃😃😃😃

Já trabalhei numa retificar 😃😃😃😃👍

مصنوع من مادة A 60 خاطئ المادة غير صلبة

Это запчасти для хаймерсов или челенжеров?

nice eye precission setup on the lathe ;-)

It should have been preseed on and brazed after that

Beleza muito legal 👍👍

Kitna time lagta hai isko banane mein?

good tell 23:57

Measurement blue print before lathe...?

Припой хоть на мм протёк?

Eu só torneiro mecânico a 34.anos sempre usei ipis segurança em primeiro lugar

Nice job, nice photography, try a bit if slow motion photography. N. E. U. S. A. Quincy, Massachusetts

Não aceita erros se errar perde toda engrenagem aí que falo da trabalho pra fazer aí e puxar o escorpião pelo pé e caro. Trabalho top exelemte

Já caiu um cavaco no meu olho, e eu usava óculos de proteção, até hj depois depois de 38 anos como torneiro mecânico não sei pq esse pessoal Não Usa óculos

No pues el que sabe sabe...muchos que se dicen torneros....no saben ni usar un Vernier pero pa cobrar que tal....y más aquí en la alcaldía de Tláhuac

It's good to let the swaffs fall out of the work piece if it's long swaffs can get tangled to the arm or around your neck u know it's always sharp

Muito folga entre a engrenagem e o eixo Nota 0 Vai fica exentrica a engrenagem do eixo Após a soldagem

Hello j nanga innum speeda seivom

He eyeballed the runout to 0.02 mm.

Te pasaste con el torno 😅

don't no what it's for but nice jub 😎👍

M Karachi se

Im a time served Fitter/Turner and this is most definitely not the proper way to do this in so many ways. Definitely scrap heap challenge engineering at it's best LOL

New technology?

به تراشکار بگو با اعتماد به نفس کامل کار مردم رو خراب کرد. 😂😂❤❤ درود

Geeeeez >> He could have Thrown that Helical Gear onto that shaft from 20 feet away ..and it still would have gone on side ways !

Old USA when they made parts in the states, now we have to wait months.

Надо закалку сделать шестеренки

Не один резец не возьмёт хорошую шестяренку а такая сыромятина и ходит не долго

I like to see the tidy shops. Working in filth doesn't give people confidence in your work. These guys put the effort in.

Cast iron bar? I think not. But, far better work than most of these backwater machine videos. At least I saw actual measuring tools and proper wrenches.

it is not cast iron

I won silensar maruti car 800 5 speed brother halp me.

Ok

An old pair of calipers and a can do attitude.

That was wrong in so many ways

Nos profissionais tem que respeita a máquina porque a maquinas não respeita ninguém

I see you are amateur machinist.. Good luck.

There900 0NThanks

Я боялся что бы его футболку не наматало на станок вместе с ним 😂