Nothing better than getting home from work and then bing a new video from Ivan.....let's go 😅

8 months ago I knew what the problem was but wasn't quite sure now Im back researching and behold same model and engine. I've seen your videos for years and very appreciative. Thanks for your help. Keep people like me make the impossible, possible period.... Hail Pine Auto!!

Hey Ivan, did you see your brake fluid turned transmission fluid leak short made it onto the “just rolled in“ video?

It's really a shame that so many shops are just parts changers. It's made me want to learn more about my vehicle so I don't have to deal with that.

Always love your videos Ivan!!!

I am wanting to say Scotty Kilmer has stated that these model years of Toyota engines have problems. My neighbor has a 2008 Camry with 85,000 miles that burns oil; it seems the piston rings that year were junk. I have a very good friend that works on many Toyota cars. He says he stays busy; but not as busy as techs that work on some other makes. GREAT VIDEO!

The oil control filter is worth changing. It is under the number 1 cam bearing saddle.

Thank you for all your help on how to diagnose

Honestly I would wish you would do more than just one video I would love to see you do one at least every other day there's just something about the way you do videos I love it

Machines break! Some claim Toyota never break. This proves them wrong! Looking forward to the repair, Ivan.

Thanks for the video Ivan.

These are exact symptoms when the intake camgear and tensioner goes bad and it prevents the timing chain from spinning freely which messe with the oil control solenoid and crank position sensor

Quick diagnostic, Ivan! That can get expensive and time consuming, if the phaser or part of it has grenaded. Curious top see the repair episode. Crankshaft and camshaft position sensors replaced just because - no diagnostic made.

Since there is going to be a part two, I can only assume that the customer had approved repairs. Sweet! Hopefully the timing chain is not too bad.

Looks like your fun never ends.

The '13 and up are the intake phasers. I've heard a ton of these rattling on start-up.

I just replaced the timing chain and gear on my 96 Chevrolet K1500, it cost anywhere from $19 for (Chinese junk) to $50 for a Cloyes double roller chain (fit like a glove). I once tried a Engine Tech (Chinese Junk) and it had more slop than the original GM with over 200,000 miles on it. I really don't know why manufacturers are using this expensive complicated cam drive systems (Ford F150 5.4 3 valve instantly comes to mind), maybe emissions and or gas milage (really don't care), but I'm going to keep rebuilding all 3 of my old trucks and save $80,000/truck and avoid dealing with this BS.

My family has a 2012 Venza with the 2.7lL same codes but no stalling but noisy when engine is cold, parts in Canada are $840 for exhaust phaser/gear…Toyota has a big problem with this part design

Can’t wait for repair 🤠

Hey!! There's a guy sneaking around in the bushes behind you!

Thanks Ivan!

I guarantee you it's the camshaft gear what makes me think that is because it rattles on startup even if you already started it up sometimes they do rattle on startup whenever it's a cold start but then once it gets oil pressure it should not rattle so this is telling me that the locking pin on the timing gear is broken or something

4th generation Honda CR-V’s had the same issue with the phaser assembly failing.

Were there any great vehicles produced in the 09-12 timeframe?

The timing chain on the Camry is it the same as Honda as far as inspecting for issues with the chain guides to replace if bad. Is this engine an interference engine?

Replace both intake and exhaust camgear timing chain tensioner, timing chain and guides

What about if you don’t have voltage la vvt selenoyde no going to work too

Shoot, our 2009 1.8 L Corolla was getting noisy enough that I went a step up on oil, 5 - 20 to 5 - 30 so for now its better. Fingers crossed it just a Camry thing!

be care full some of those camery engines have a recall for slugging due to small oil tubes when the engin was built. there was a few class action and extended warranty's on the engine and rings.

Somewhat later model Toyota Sienna engines have a water pump that’s undersized, and bearings wear out at about 100k miles .. they’re a bitch to change, as they are very hard to get to .. lots of tear down required.

What is an oil control solenoid?

Stretched timing chain and needs new intake and exhaust camgear along with tensioner and guides

265,000 2009 ccamry. Runs great

Toyotas are bullet proof… except for the 2AZ-FE oil burning low tension rings engines, 2AZ-FE head bolts recall, rusting frames, head gasket issues…

This is Houston control. We are on standby, waiting for ignition. The weather is fair and lift off should commence shortly.

Great

Ironic that Ivan releases the video on the day that my 17 year old Toyota turd wagon is up on the jack stands getting a used engine put in. In my case the head gasket failed - definitely on cylinder 3 put possibly 2 as well. Coolant was seeping into the cylinder and causing a misfire on start up and difficulty starting and cylinder 1 plug was completely black so the oil burning on that cylinder seems to have been ... bad. Oddly enough if I gave it the beans it would generally clear up and run OK as long as you were maintaining some kind of throttle. I had just been topping it up with water once a week for the last few months but it got so bad it needed sorting. It nearly stranded me the other day. I had to put my spare plugs in and use some easy start to get it to fire.

People don't realize, but them damn VVTI / oil sensors can cause catastrophic failure. 2014 Buick verano under 100,000 mi started dying randomly on light throttle The lightest of throttle, kept getting camshaft codes. Couldn't figure out personally had to take it to a local and trusted shop, $300 later problem solved mechanics that he had to go and look up the symptoms but couldn't replicate himself replace both oil sensors with dorman (😩) parts because this was during COVID and the parts crunch was here and he couldn't get ACDelco as requested. Anyways speed up to about 50,000 miles later same problem arises, but this time funds were low and I wasn't able to fix the problem because it really didn't happen that often and it seemed like the harder I was on the gas It wouldn't die but sometimes it would run rough or die especially at stop lights. Well anyways my repeated driving like this eventually I was taking a corner in a very urban area parked with cars along both sides at a very early morning quiet time, and I could hear on heavier throttle around the corner severe engine clatter and it only seemed to get worse but would only happen on heavier throttle. I immediately baby the car home never going over 1,200 RPM if possible, was very worried was not happy I thought I destroyed something because that noise was severe and like I said I replicated a few times and I knew exactly what it was. Anyways the next day I replaced it with ACDelco solenoids, problem is gone no more engine chatter either. It's funny how these little damn sensors can cause catastrophic failure if not remedied quickly after signs show up that they are failing, when people think of censor they don't think that their engine can grenade or get permanently damaged. I haven't finished watching the video but I wouldn't be surprised if the chattering went away after replacing the sensors with brand new ones and if they didn't go away after that permanent damage has already been done. This is also definitely related to oil changes as well, you have to be exactly at your engines supposed interval if not sooner with full synthetic I wouldn't go more than 4,000 miles on a oil change today. The longer you go on oil changes the quicker the solenoids break for whatever reason.

Fellow shop owner has a Tacoma in his shop for a transmission. Guess the transmission cooler line blew out and they kept going. He said to buy all the pieces of the lines its almost 2k

The solenoids looked different. The pattern of the cutouts seemed different. I wonder if they need to be swapped back.

Sounds like the cam phasers are going out.

Didn't you have a case six or more months ago were there was one of these sensor that had a piece of something in it.

Ivan i would tell the customer to source a second hand part would not pay that price

Replace both phasers. The intake causes a rattle the exhaust fails catastrophically. The rattle breaks the upper guide. Standard motor products phasers are OEM. Read the tsb carefully. The intake phaser must be in the unlocked position until after the bolt is torqued. You CAN NOT replace the exhaust phaser without removing the timing cover. If you see a wear mark on the cover Infront of the exhaust phaser then the ring is moving and it will fail.

Not that it would help in this case but Toyota should have made this a 100K warranty. That part should not break especially that big spring.

The upper chain guide is likely broken.

That's pretty crappy that they put a time/milage limit on warranty repair. They know it's a bad part, they know it's going to fail at some point. Just because you're lucky and manage to last longer than others, it's still a design flaw that's caused the problem. In fact it makes you unlucky because your now outside of free repair.

The Toyota parts are sometimes Super Expensive (Lexus as well) BUT thank god that they actually still have the needed (in the case, so far) part or parts.....life is a bitch, these days....

VVT solenoid?

Its rare Toyotas breakdown. Most of the time is lack of preventative maintenance. Our 09 Toyota Venza has been bulletproof with 215,000 miles. still drives like new. Oil changes on time can prevent problems like this.

Here's the crazy thing. Toyota will work to correct these issues so they may go a few years and then resolve it. FordTechMakuloco recently had a video and he explained a problem Ford has had with axle splines for 10 YEARS and haven't done a thing about it. They add a washer if needed but never changed the detective part. They just keep pumping them out to this day. Even on the new Lightning.

I have driven one of them & they're a bit gutless, they have as much power as the old 127 kilowatt 3.8 litre Buick LN3 V6 engine which Holden bolted into the series 1 Holden VN Commodore in 1988 when the proposed Japanese sourced Nissan RB30E engine got too expensive once the value of the Japanese Yen for against the Australian dollar. It would've been a nice car particularly if they carried the turbocharged 150.kilowatt version (RB30ET) over to the VN Commodore & several prototypes ran that engine. The Buick L36 V6 engine was a brumby (wild horse) in comparison to the silky smooth Nissan six & the U.S. sourced engine was initially a problem as far as coolant Leaks goes where the welch plugs became the sacrificial anode so GM & Holden replaced the welch plugs under warranty with stainless steel items & added 3: aerobic sealing pellets to the coolant reservoir to.seal.up.any potential further coolant leaks around the welch plugs. Holden replaced a lot of the graphite impregnated rope rear main oil seals under warranty as well which wasn't a problem with the Nissan RB30E engine. The next L27 V6 engine had troubles with the 1 piece rear main oil seal sitting squarely inside of the rear main bearing cap which caused a potential oil leak sometimes !

I have found through experience using the OEM oil filter is better for these cars. Better oil pressure and better oiling on the top end of the engine.

Remember the secondary air injection problems on the mid 2000's Tundras? Another defective design. Toyotas are generally great, but some are better than others. There's a guy here that bought a 2016 Sienna - that thing has not been too good to him. Now it's rotted so bad it won't pass PA inspection.

I would also try not to drive it until after it's replaced because if the phasers coming apart there is a high chance that you can crash the valves

had a 2014 drop a chain at 80k, rattle on start up, had gr v6 phaser come apart and eat through front of cylinder head. had oil feed line on gr v6 explode , toyotas are just like the rest, they all break

👍

Time to scavenge a junkyard for a working used gear? I'm thinking that a cheap fix could be to lock the gear in a fixed position that works well for idle and low rpm. Not ideal, but cheap, but that depends on if there are inspections that will fail due to DTCs being set and the car sets a timing DTC.

What happened with the filter?

I would bet you that the owner did not religiously keep up with the oil changes to that engine.

all this new tech is great until it breaks

They break all the time. Both my parents drive Toyotas. Dads Tacoma needed driveshafts at 23K and an AC compressor at 64K. Moms Camry hasn't hiccupped yet but it doesn't have 10K on it. Nevermind the nearly brand new 09 Camry that went full throttle through a busy intersection killing my friend and her 2 kids.

Let's all hope that the phaser didn't take out other components with it. Toyotas don't break often, but when they do it gets expensive.

It seems almost everything is more expensive these days.

My buddy saw how reliable the Camry is as i have the generation before this one. He bought this same generation and had nothing but problems with it.

#Don't tell Scotty

Not even knowing anything about the maintenance history of this car, it is clear that this car has been neglected and abused. The main gauge cluster lens is disgusting.

It's shaking because it's afraid to tell you what is wrong with it.

I think the 09-11 had a factory defect in the vvt-i actuators

Toyota engines are generally well engineered and are reliable if you don't skip maintenance. HOWEVER, it doesn't mean that its parts suppliers don't err occasionally. Toyota is pretty good about going to a different supplier once they identify defective parts, but the customer is still left to deal with them should he be so unlucky as to receive a defective part. They almost always break outside of the warranty period.

I have red four Toyotas they all had problems and eventually broke In one way or another.

Parts are expensive and labor is expensive now. Oh well, what can do.

I'm surprised, an oil change usually fixes that😅

Maybe have AUTOSTOP BUTON...HAHAHA😂😂😂😂😂😂😂

Check the oil level. Those engines burn their oil.

If you want to break an engine, just let me drive it around a while 😂

I only click on be cause tidal said broken Toyota, Toyota's dont break so I had to take a peak make sure it wasn't a newer model with low milage like that 2015 or 16 Cherokee that you had couple weeks ago.......

Looks like owner went hog wild with spraying Armor All on the dials....

I know what Scotty Kilmer would have to say about this...

Camry was heavily neglected.

In this day and age, Toyota is the best of the worst

No they can NOT break. They last forever, it's your misdiagnosis of a perfect engine, shame on you.... Scotty Kilmer

Toyotas have had some weak points here and there, but I’ll still stand behind them over anything else. Though not quite as efficient as some of the newer stuff, the old 1MZ FE is a tough act to follow. 👍👍🇺🇸

Every video gonna have a part 4 now? 11k ppl in 4 hours so i guess ppl like those but man i hate a to be continued on a car bro

An engine with a known issue doesn't manifest that problem until 180,000 miles. I'd say that's pretty darn reliable.

They’re no better than any other manufacturer but Toyota owners tend to take better care of their cars and Toyota has always been waaaay ahead any other brand in costumer satisfaction

They rarely break down, two at our house, both over 12 years old, besides servicing they have cost us £200 in eBay parts and repairs 🤓 ALL Japanese brands are robbing customers with their spare part prices, I guess it’s because they don’t break down so much so the garages have little income from repairs?

I really don’t care what brand it is they all break. They’re mechanical and can and will break. Change my mind.

Still cheaper then buying another car.

Hello

Toyota's and Hondas are still the most reliable cars on the planet

Well, a 2011 Camry with nearly 200k miles is still worth at least $6,000. That is another reason to like Toyota. About the only thing that would make one not worth fixing would be if it had a major wreck or it was a victim of a flood or fire. Not many cars can make that claim.

Scotty has been lying all these years

cheap gas

Seems like Chevy and Chrysler owners can’t wait to comment on how crappy Toyota’s are…this thing has 180k miles folks!!! A phaser going out at that mileage would be normal maintenance in my book. Anyone who watches South Main Auto will know that it is VERY common to have Chevy and Chrysler products only a few years old and with less than 50k miles having MAJOR repairs done. I’ll keep my Toyotas…thank you very much

Toyota's only fail thru poor maintenance only...in which case self inflicted ...

Toyota's are Junk. Way overrated. I stick with Chevy and Ford.

Why not just put it all in one video