Super bro very good thank you so much continue you this tractor valve adjusting full video i am weighting ok thanks
@tractorsmarinemechanic3 жыл бұрын
Ok.I will prepare my video just for you.pls hits like and share.thank you
@marioc92313 жыл бұрын
Hi bro. There were no Valve Seals .
@tractorsmarinemechanic3 жыл бұрын
Yap! I also wondering why No valve seal.
@MrToluen603 жыл бұрын
Very good job !
@tractorsmarinemechanic3 жыл бұрын
Salamat sa panunood.
@josephfriasgalpao21082 жыл бұрын
Idol..🙋🙌
@tractorsmarinemechanic2 жыл бұрын
Salamat din idol
@rolandoquisperoch43762 жыл бұрын
Amigo tendrás cigüeñal de un tractorcito shibaura su1540
@JanJan-tt7jz2 жыл бұрын
Hello, I have a kubote l1511dt with a Z751 engine, I wanted to find out where the cooling pump is in this engine.
@tractorsmarinemechanic2 жыл бұрын
Thank you for watching.please subscribe, share and also hits like. That unit or tractor there is no cooling pump.its only a radiator. after the water is boiling it goes to the radiator.
@JanJan-tt7jz2 жыл бұрын
Guided by such a rule, and just wanted to make sure. Thanks for the info and you have lots of cool kubota videos
@tractorsmarinemechanic2 жыл бұрын
Thank you.
@vaskful2 жыл бұрын
Hi, what are the dimensions (diameters) of valve seal for D750 on b7001. I have problem with it, my local dealer sent me wrong for three times. if it is possible share a link where i can buy it. Thanks
@tractorsmarinemechanic2 жыл бұрын
Inside diameter is 10.5mm.
@rubenmartinez76172 жыл бұрын
need some help, 1979-1982 ford tractor 1100 shibaura LEK752C diesel 2 cylinder what's the compression and where to buy parts thanks.
@tractorsmarinemechanic2 жыл бұрын
I'm sorry sir I have no idea.its very difficult to find spare parts for that tractors
@rubenmartinez76172 жыл бұрын
Ok thanks for your time and help
@rubenmartinez76172 жыл бұрын
Any idea about the compression also the gap of the valve thanks
@tractorsmarinemechanic2 жыл бұрын
The Compression ratio of an engine is a measure of how much the air mixture is compressed in an engine cylinder.it is calculated by dividing the air volume in one cylinder with the piston at BDC by the air volume with the piston at TDC.the air volume with the piston at TDC is called the CLEARANCE VOLUME.it is the clearance that remains above the piston at TDC.are you a student?The gap or clearance for your engine is 0.25mm. thank you for your comments and for watching.
@tractorsmarinemechanic2 жыл бұрын
Please watch also from my playlist on how to tune up or how to apply valve CLEARANCE for your engine if you do not already watched.kzfaq.info/get/bejne/pZp3ds2b19yomKs.html
@janithsithum320110 ай бұрын
Is the valve seal moving when valves are woking?
@tractorsmarinemechanic10 ай бұрын
No
@janithsithum320110 ай бұрын
OK THANKS FOR THE REPLY 🙏
@vovaborovitskij28063 жыл бұрын
あなたは最後までビデオ休憩することができます
@tractorsmarinemechanic3 жыл бұрын
Thank you for your suggestion and for watching.hope you subscribe to my channel.