Tremec TKX 5-Speed Manual Transmission Conversion at V8 Speed and Resto Shop

Рет қаралды 32,430

2 жыл бұрын

We're Hiring! v8speedshop.com/online-job-ap...
Tremec TKX 5-Speed Manual Transmission Conversion at V8 Speed and Resto Shop
Manual transmission conversions are getting easier thanks to the new Tremec TKX 5-speed overdrive transmission at the V8 Speed and Resto Shop. The TKX offers not only a smaller case design, but also improvements in shift quality over the popular TKO series transmissions. The TKX makes it easier to fit into cars like this 1966 Pontiac GTO, or early Mustangs, Camaros, Chevelles, GTO, Galaxies, and other popular Muscle Cars.
We recently completed the install of a Tremec TKX with a hydraulic clutch from Modern Driveline, and we were impressed with the fit. The TKX has a torque capacity rating of 600 lb. ft., and they claim 8000 RPM maximum shift RPM thanks to the Sintered carbon and bronze-Hybrid double-cone synchros with a non-leading edge profile direct from the T56 Magnum. The case design is “front loaded”, and features increased strength with a three-piece aluminum housing. Gaskets at all flanges simplify installation and eliminate fluid leaks.
- Here's another 5-Speed Chevelle Video: "1969 Chevrolet Chevelle SS Big Block 5-Speed Upgrades Feature Video V8 Speed & Resto Shop V8TV"
The TKX is available in GM 3 & 4 speed Muncie/Richmond pattern, as well as Ford wide pattern 3-4 speed cases to suit many applications. Multiple gear ratios are available, which allow you to tailor the transmission gear spread to your driving needs. They all feature overdrive. This video contains a Tremec TKX review and TKX install overview.
- More information about the Tremec TKX is found at www.moderndriveline.com and we are always happy to discuss installing one in your classic or Muscle Car at the V8 Speed and Resto Shop. You can reach us at www.v8speedshop.com today.
314.783.8325
SUBSCRIBE: goo.gl/RIkdDS
www.v8speedshop.com/contact
The V8 Speed & Resto Shop is a full-service classic car and muscle car restoration service ready to perform everything from simple maintenance on vintage cars to full frame-off restorations and modifications. Whether you are seeking a stock restoration, a pro-touring muscle car, or a custom restomod, the V8 Speed & Resto Shop in Red Bud, IL, can help. Contact us today to put the V8 crew to work for you. Transport services are available.
V8 Speed & Resto Shop
817 S. Main Street
Red Bud,IL 62278
314.783.8325
www.v8speedshop.com/contact
Email: resto@v8speedshop.com
#TKX #5speed #v8speedshop
• 1969 Chevrolet Chevell...
V8 shirts, hats, and more:
v8speedshop.com/shop/

Пікірлер: 43

@V8TV 2 жыл бұрын

You can reach us at www.v8speedshop.com/contact to plan your TKX swap!

@charlesdalton985 2 жыл бұрын

Man, you want to talk about a dream come true! That is a game changer. Thanks for sharing 👍

@AnnatarTheMaia 2 жыл бұрын

I have a TR-6060 in my car and it is the smoothest, most precise transmission I ever drove, and I drove everything from Trabant's column shifter to a Subaru to a Volkswagen to an Alfa Romeo and many more to the TR-6060. Absolutely fantastic. My next project will have a Tremec Magnum.

@jameshutchins3396 2 жыл бұрын

Sweet. A win win for everyone

@waynehoffman1791 Жыл бұрын

Well presented video Kevin! I installed the TKX in my '70 Chevelle SS396 L-78 a couple months ago. I honestly fell in love with the '70 all over again...what an incredible upgrade from the Muncie M-22. The TKX's performance is second to none, plus peace of mind that I'll make it home as the Muncie was, in my opinion, a piece of junk. If the M-22 wasn't so valuable to old school purists, I'd toss it in the nearest dumpster!!

@V8TV Жыл бұрын

Thanks for the kind words, they are fun transmissions!

@marx769 2 жыл бұрын

Great info! I REALLY want this for my 70 Chevelle that is currently an auto car.... time to start saving! I'll look you guys up

@V8TV 2 жыл бұрын

Thanks, we'd be happy to help!

@jasonhull5712 2 жыл бұрын

Looks alot easier to install than the TR6060 I just put in my ol Camaro.

@BrightStar3862 2 жыл бұрын

Fabulous install, and great looking machining - even though not seen.

@V8TV 2 жыл бұрын

Many thanks!

@bruceh92 2 жыл бұрын

Kevin love your vids man.

@V8TV 2 жыл бұрын

Thanks Bruce, appreciate you taking the time to check them out!

@ClockFixer 5 ай бұрын

Tremec's had a lot of problems with Bearing Failure back in the day............hopefully they have Resolved that!!!!!

@V8TV 5 ай бұрын

The TKX is an amazing transmission. Tremec really improved so many aspects of the 5-speed that these are a complete joy to drive. They shift at high RPM, have smooth actuation, and handle power. Very nice units.

@adammcilmoyl4278 2 жыл бұрын

Is that trans mount location the same as the Muncie and T10? Sure looks like it... this might be a whole lot easier to deal with than my T56

@artcrow1968 Жыл бұрын

I am just wondering what is the usually cost without any tunnel modification for this type of job? Just labor estimate? I know each job is different but wanted to get an estimate? I want to get one put into a manual 4speed big block on a 1971 chevelle. Also do you have to change the bell housing and if you don't change the factory bell housing do you still have to do these measurements on the alignment of the bell housing? To keep the Tremec warranty valid?

@user-wd3mv9kt7e 2 жыл бұрын

What about mopar? 68 charger fitting.

@txnetcop 2 жыл бұрын

Saaaawwweeeetttt!

@johnmilner7603 7 ай бұрын

I’m rarely on the highway so I’ll stay with my Muncie in my 70 Z/28. I don’t want to take a chance on having to butcher up my floor.

@jagco2594 4 ай бұрын

What parts needed to make this with work chevy 350. Clutch, pressure plate - they make fingers that don't stick out some much, flywheel. 2 peace main, What's the specs on the bearing fully close. I need to lose 0.44 spacing. To use a hydraulic bearing. 1.710 bearing closed press in on the clutch fingers.

@ModernDrivelineInc 3 ай бұрын

Hello here;s a little info for you... For GM applications there are multiple pressure plate configurations. 3-Finger Style All are tall and cannot work with hydraulic release bearing. Diaphragm Style Flat finger, tall, for mechanical bearing Flat finger, short, for hyd bearing, requires radius face bearing Raised finger, tall, for mech bearing Raised finger, short, for flat-face hyd bearing A Tilton brand bearing is 1.78" tall. ALL hyd bearings need 0.125" ideal set-up for new clutch; this provides wear clearance. So... if you have 1.71" + 0.125" set-up gap... your ideal minimum is 1.835" This can vary slightly based on new or used clutch, and type of friction materials. You will need to tell us what you have. Options: Add a spacer plate, 0.250" Trim base of bearing retainer tube IF there is enough material to do so - this is assuming you have a slip-on style bearing. If you have any further questions please call us at 208-453-9800. We are always available to help, we love working closely with the professionals at V8 Speed & Resto.

@MrTwins3950 Жыл бұрын

Can u provide rough estimate? Interested to upgrade from Four speed Muncie? 67 Lemans Convertible!

@jagco2594 Жыл бұрын

will it handle sticky tires

@Brass_Heathen 2 жыл бұрын

what's the msrp on one in cdn $?

@jagco2594 Жыл бұрын

Can you drag race this trans with slicks on a car.

@bikesandmore2320 Ай бұрын

What brand hydraulic throwout bearing do you guys recommend?

@michaelclarke9488 2 жыл бұрын

Is there any provision to allow the stock, left offset, shifter position that the 64-67 Pontiacs use?

@V8TV 2 жыл бұрын

Good question, we'll ask!

@cyclonekevin6199 2 жыл бұрын

That car would b cooler, if it had a Pontiac engine instead of a Chevy. Just my opinion.

@V8TV 2 жыл бұрын

Thanks for the feedback and being cool about it even though it's not what you would do. Appreciate it man!

@cyclonekevin6199 2 жыл бұрын

@@V8TV Not hating on the build, to each it’s on. It’s such a go to thing to drop a Chevy engine in every car.

@bigredc222 2 жыл бұрын

@@cyclonekevin6199 I like cars all original, but once you start turning it into a restomod or pro-touring car, you may as well go all the way. LS's are so much easier, cheaper, and almost headache free compared to getting equal power out of a Pontiac engine.

@cyclonekevin6199 2 жыл бұрын

@@bigredc222 That makes sense

@moo.johnference869 2 жыл бұрын

@@cyclonekevin6199 tell us about your car Kevin. Your real car not one you think you might want .

@thephantomzoneboxing 10 ай бұрын

what car on the tumbnail??

@V8TV 10 ай бұрын

1966 GTO.

@rm6330 2 жыл бұрын

5:14 what happened Mr Drifter?

@BigBoob734 2 жыл бұрын

Do you guys build big rim car’s?

@V8TV 2 жыл бұрын

Depends on what you call "big".. we've gone up to 19s - 20s on Muscle Cars, 20s ish on classic trucks, but not bigger like 24"or bigger on cars.

@joshuafuller9898 2 жыл бұрын

@@V8TV There's a vote for good taste...

@moo.johnference869 2 жыл бұрын

It doesn't matter the name on the block chevy,ford, Chrysler, what matters is the right name brand of parts and the correct selection and machining that work together with each orther to suck in air and spit it out with the least effort ! Chances are that chevy engine transported in another name brand automobile body doesn't have a single chevy made part in or on it , so is it a chevy ? FU.K NO ITS YOUR ENGINE ! You dreamed it, you nursed it, you built it your way with your selection of vitals with your hands . It's not a chevy, ford or Chrysler it's your engine.