Great video. All the parts he tested are most of the normal 5 or 6 parts that typically break on almost all makes and models of a standard gas dryer. Take note of the igniter turning white hot. They will sometimes still glow when they are actually broken. The white hot glow as opposed to a lesser reddish glow is necessary for the igniter to complete the cycle in order for the gas valve to open.

Thank you very much for making this video and helping us learn how to repair our own dryers . Thank you again,Have a bless day

Thank you very much for this excellent video about the Maytag gas dryer. Your instruction was extremely helpful towards resolving a gas dryer not heating. May God bless you and your family

Replaced thermal fuse with your help, and yahoo, our dryer is heating again! Thanks for the informative video!

Thanks for taking the time to create this video. Your detailed steps saved me a $200 service call! Much appreciated.

Very good video! For me, it was a dead fuse. I never would have known where to look. Thanks for sharing!!

super job on this video - showed me exactly how to disassemble and diagnose the issue - much appreciated.

Thanks for this video. With your instruction, I was able to successfully troubleshoot and replace the bad part.

Thank You very much for taking the time to make this video....I was able to figure out I had a Bad "Cycling Thermostat" I replaced same and was able to breathe New Life into my 25+ yr Old Maytag Dryer...more Beer $$ 4 Me!! :)

Thank you for your video! I had the exact same dryer and issue! God bless you!

Great Video got the same dryer had no heat. Bought maytag spare dryer parts off of amazon. I opened the back 8 screws swapped 2 parts put back together and bingo dryer back to normal. Thanks so much for the video.

Thank you, I fixed my dryer because of you.

Not exactly my model, but helpful to know about the peephole (no other vids for my model discuss it) and seeing what the parts do.

Helpful additional tips besides the one below: 1.You will need something to hold open/support that top lid while it is up. 2.Be careful of sharp edges on all of the metal panels. I cut myself a couple of times. 3. By moving the dryer around with a ridge copper connector like this one you are taking a chance of disrupting the gas connection which could cause a gas leak. I suggest you at least try to tighten the connections before putting back in place. The best scenario is to have a modern flexible gas connector. 4.

Very well explained. Thanks

Great video and explanation. 👌

Very details, thanks

Great video A+

Great video! Helped me out a lot. Thanks for posting!

Thank you for uploading this! It helped me to fix mine and save me a lot of $$$

Thanks for the video

Does dryer got to be on when you relight pilot light t

💯 Helpful Thank You

great video i have same dryer no flame thanks ill chk the back first I figured most of these can be jumped out but i wont keep them jumped out deff not safe Thanks again excelant video

Thanks for the full diagnostic, now I know how to get at my felt seal! I see that your dry has black/carbon on the hot air supply grill. Seems odd, our machine is about a year old and I was wondering about it. I don't know what tugged my felt out but it didn't tear so I can remount it.

Thank you for taking the time to record / post this. Saved me a fist full of Ben Franklins ! $6 part fixed it. MAGA

MY dryer has a little blue disc in the wire loom leading to gas solinoid what is it and how to test it.

What do you do if everything has continuity? Still no glow or heat. Same dryer as the one in the video.

My dryer only heats on the timer setting. On auto the flame never turns on. Do you think it's the same sensors?

That is my dryer.. When tested the flame comes on but when the clothes are put into the dryer then the flame won't come on consistently.

Mine has fire on for about 5 minutes, than fire shut off completely. So the problem is on the coils ? Thanks

I'm having an issue with my Maytag but the igniter is working but won't fire up. I glows for 30 seconds then faded but the gas won't kick. It's not a supply problem. What could it be?

thanks!!!!!!!!!!!!!!!!!!!!!!!

Is it normal for it to smoke after changing the heating element?

Thank you for this video. So the only way to test the part that you replaced is to do the bypass? It can't be tested with the multi meter?

great video the only thing u did not do that u should do next time is open the piece where blower motor sits in especially if u already took lint screen screws out there are 4 more screws and in that metal duct its usally full of dirt lint and sand witch can cause over heating because blower wont pull out air this will also cause thermal fuse to blow How do I know I did the same thing and blew new fuse when i opened up duct it was loaded with heavy dirt and blower blades were also full of dirt Thanks again great video

Did you fix the problem?

Where is the pilot light so I can relight it

Can I safely jump out the thermocouplibg for now

Pilot light is off need to light it to dry clothes

FYI Buy A Flashlight. SO you and the Viewing Audience can SEE👀

Jesus Christ, all you had to do is take the back panel off to test these elements! Don't follow these instructions folks, unless you're just genuinely curious on how your dryer works as a whole, and you have a lot of free time.