How to Replace Front Wheel Bearing 2008-12 Chevy Malibu

Рет қаралды 50,153

3 жыл бұрын

Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com 1aau.to/ia/1ASHF00192
Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision. This video shows you how to do the replacement yourself on your 2008-2012 Chevy Malibu.
• Check here for more videos on the 2008-12 Chevy Malibu: • Chevy Malibu 2008-2012...
This process should be similar on the following vehicles:
2004 Chevrolet Malibu
2005 Chevrolet Malibu
2006 Chevrolet Malibu
2007 Chevrolet Malibu
2008 Chevrolet Malibu
Tools you will need:
• Pry Bar 1aau.to/oa/1AXAA00020
• 19mm Socket 1aau.to/oa/1AXAA00043
• 36mm Socket 1aau.to/oa/1AAST00006
• Torque Wrench 1aau.to/oa/1AXAA00044
• Gloves 1aau.to/oa/1AXSS00048
• Rust Penetrant
• Safety Glasses 1aau.to/oa/1AXAA00343
• Floor Jack 1aau.to/oa/1AXAA00068
• Hammer 1aau.to/oa/1AXAA00091
• Razor Blade / Gasket Scraper 1aau.to/oa/1AXAA00280
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Chevy Malibu 2008-2012 7th Generation: • Chevy Malibu 2008-2012...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 23

@TRQ 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@orionsimerl6539 Жыл бұрын

This is not the video you want to follow. There's no need to take off the tie rod end or the knuckle.

@Ken-1 3 жыл бұрын

Is this like a 1A Auto spinoff channel/brand? Dude, I recognize your voice anywhere haha, great work as always though!

@Jayyak47 10 ай бұрын

I found taking the knucke off to be helpful i couldnt reach the hub bolts with my impact wrench

@ChrisShipley-ec5qz Ай бұрын

Question can ur wheel come off riding on bad wheel bearings?

@venomrogue1 3 ай бұрын

I don’t like leaving just the lower ball joint connected. Great way damage it. Not required to remove strut bolts to do this job.

@brandtrichardson4049 5 ай бұрын

Great vid

@michealmiller6630 Жыл бұрын

Just give it a couple loving bonks!!

@MPLVT69 3 жыл бұрын

Awesome step by step video👍👍

@annaperez7383 3 жыл бұрын

Any info on the front passenger sliders and where they would go plunger side top or bottom?

@DevJB 11 ай бұрын

The top guide pin is metal. The lock pin (lower) has a plastic ubber anti-rattle tip. The lock pin is a few thousands smaller than the solid metal guide pin. Lock pins go on the lower or front most hole toward front of vehicle. Imagine car is rolling forward and hits the brakes, the force of the calipers go downward and forward. We want this lock pin to be on the lower forward spot of the down force. This lock pin rubber sleeve comes in a boot kit and should be replaced because it may swell with age or wrong grease and cause pads to stick\wear.

@tetris3289 11 ай бұрын

Wtf why did u take the knuckle out? U had enough room to take the bearing out without it.

@alanbrooks3670 2 жыл бұрын

Great step by step guide with all the info for torque specs and bolt size and you make it look easy but after installing should you have to get a alignment you did change the tie rod end wouldn't it possibly change the toe in and with un bolting the struts the camber may be off? Or is that adjusted another way

@thatvegashighrisedude2757 Жыл бұрын

Do you need to do a alignment after doing this ?

@TRQ Жыл бұрын

+ThatVegas HighriseDude No alignment is needed if you are just replacing the wheel hub assembly.

@thatvegashighrisedude2757 Жыл бұрын

@TRQ man you guys are awesome ! I bought the 2 wheel hubs from you guys , came in 1 day , and you guys reply on KZfaq ! This is why I recommend you guys to everyone I know .