Removing factory primary clutch and install the 100% clutch MOD.
Пікірлер: 34
@jeffwilliams314 Жыл бұрын
I'm new to UTV's and wanted to service the one way bearing. This showed me everything I needed, thanks for the great video
@toddnmichelle4 жыл бұрын
Great video! FYI anyone with a gen1 Outland 400 the primary clutch bolt is a left-hand thread! I just broke mine by accidentally turning too far left thinking I was loosening. Now in a world of shat trying to fix it
@TheAcefirearms4 жыл бұрын
If it’s left hand thread a standard right hand drill bit may possibly spin it out while drilling it .
@coreygilmore70732 жыл бұрын
@tiddnmichelle did you get your bolt off I just did the same thing on mine....🤬
@toddnmichelle2 жыл бұрын
@@coreygilmore7073 I had to take it to a mechanic - they got it out no problem. I wound up with too much money in the whole project and sold it once completed to break even
@gildemarlinspimenteljunior86344 жыл бұрын
Good Job friend !
@truth2power5286 жыл бұрын
Thanks for the video. Going to replace one way bearings in my father in laws 05 can am/ bombardier outlander 400. Haven’t looked at it yet to see if it’s similar setup. I’ll be finding out soon.
@gordoncullen71762 жыл бұрын
i dont mean to be off topic but does someone know a tool to log back into an Instagram account..? I somehow lost the account password. I would appreciate any tricks you can offer me.
@lucahugh72092 жыл бұрын
@Gordon Cullen instablaster ;)
@gordoncullen71762 жыл бұрын
@Luca Hugh Thanks so much for your reply. I got to the site on google and im in the hacking process now. Seems to take a while so I will reply here later with my results.
@gordoncullen71762 жыл бұрын
@Luca Hugh it worked and I finally got access to my account again. I am so happy! Thanks so much you saved my ass!
@lucahugh72092 жыл бұрын
@Gordon Cullen glad I could help xD
@POPPING4178 жыл бұрын
Alright, preciate it.
@peterlogan16232 жыл бұрын
Beware the 400 engine has a left thread on the primary clutch retainer bolt
@POPPING4178 жыл бұрын
Thinking of sending my 2013 commander clutch to get the lock up mod. Since your install, have you had any issues? Also, what other parts (besides the sealed bearings) would you recommend I upgrade while I got the clutch assembly apart?
@TheAcefirearms8 жыл бұрын
Dalton clutch kit with low engagement spring. And a 212 Maverick belt.
@amelsahman24144 жыл бұрын
how did you block the pulley when you unscrewed and turned the primary screw, was it possible to damage something inside from the pressure, rollers or weights or roller shafts or weights
@TheAcefirearms4 жыл бұрын
Amel Šahman that round stock is 1/2” I think. And no it fits in through the hole in the governor cup and just binds the two sides . Plenty of aluminum to get it loose or tighten it with any damage. At least I haven’t ran into any issues and have done that one in video at least 6 times . Not to mention all the others .
@roadrnnr20089 жыл бұрын
What about out backing off the Bolt and retorqueing when putting it back together?
@TheAcefirearms9 жыл бұрын
roadrnnr2008 Only reason for backing off primary bolt would be for bolt stretch. I have had several of these off with no issues. Not saying it wouldn't be a good idea. But for me I don't find it is needed.
@montanaelkwhisperer17442 жыл бұрын
How about using a fat rubber band to hold the cups and springs in place while you push the one way back on? 🤔
@TheAcefirearms2 жыл бұрын
Putting the one-way back on isn't typically when they launch. It's when you remove the one-way. But yes as long as the band slides off the cups and can then be removed its all good .
@pricetag30 Жыл бұрын
Watched twice and never saw any MODS??
@faycelouedrhiou95383 жыл бұрын
What is the lenght bolts of clutch please
@TheAcefirearms3 жыл бұрын
Not sure and I don't have any laying around to measure them or I would. Sorry I couldn't help.
@jasonadkins56006 жыл бұрын
does this mod work for the 2013 maverick?
@TheAcefirearms6 жыл бұрын
Jason Adkins no the hp is to high. You might look into the Mav turbo clutch.
@nathanrobinson11745 жыл бұрын
@@TheAcefirearms does this work for 2018 commander 1000r
@TheAcefirearms5 жыл бұрын
Nathan Robinson not sure if it’s been done yet or not . Check out uatv-tech.com send them email. For a update .
@pricetag30 Жыл бұрын
Where does the LUBE go??
@TheAcefirearms Жыл бұрын
The factory bearings are only sealed on one side. The skf bearings are sealed both side. Run them till the go out then replace. I have ran the skf bearing for 4000 miles no issues.
@veseljkovesic23804 жыл бұрын
Hat Jemand Videos von tgb 1000 von variomatik.ich brauche wechsel aber keine Chancen geht nicht draußen Achse von Kurbelwelle
@TheAcefirearms4 жыл бұрын
Veseljko Vesic sorry your comments not in English. So I have no clue?
@TheAcefirearms5 жыл бұрын
Ok I have got a couple email notifications recently of question being asked but they aren’t showing up here in KZfaq. So if still needing answers email me directly at . Acefirearms@gmail.com thanks