Unboxing the PwnCNC Spindle Kit

Рет қаралды 10,632

Күн бұрын

Do you have questions about what's included with our PwnCNC Spindle kit? This video will help you answer those very elusive questions.

Пікірлер: 25

@lstineman 7 ай бұрын

Awesome.. finishing my shapeoko 5 pro build tomorrow and will unbox the PwnCNC spindle and hook it up. Thanks for the video, great explanation.

@k9rdog Ай бұрын

Do you have a video for the open Builds 1010 lead machine?

@talegunner4414 Жыл бұрын

Did you do a tram on the spindle after installing it?

@Kathyoftheglade 3 ай бұрын

Just bought a tramming tool from you. It's perfect. The sticker is now on the side of my controller. Thanks for a great tool. If I upgrade the 300w spindle I may go to you.

@F4CreationsNJ Жыл бұрын

I am about to purchase a Sienci Longmill MK2 and looking to use one of the 65mm Spindles. Is there any video or documentation on that?

@PwnCNC Жыл бұрын

Installation on any CNC machine will likely be super easy. Most machines accept the PWM/GND signal for control which is perfect. Our vfd can be modified to support 0-5v or 0-10v which is the most common voltage ranges or anything inbetween. All you'll need to do is identify those two pins on your Longmill controller and you're golden. Plug in our control wire and you'll be set to go for automatic g-code control of the spindle motor.

@AppleBag1000 19 күн бұрын

what benefit other than it being a plug and play set up, and better quality VFD you use, is it to buy your 220v metal working spindle kit, oppose to buying the g-penny spindle kit with the same specs?, 700 is a major price difference

@PwnCNC 19 күн бұрын

support.pwncnc.com/kb/article/182-why-should-i-buy-a-spindle-system-from-pwncnc/

@velocityacoustics 7 ай бұрын

Whats the difference between your 110 volt and 220 volt spindles? is 220 something i really need?

@daveyJ213 6 ай бұрын

What touch screen computer/device are you using? Currently I have to carry my Mac laptop out to the machine and connect with USB. I have an iPad also, but I don't think there is a version of Carbide Motion that runs on an iPad. Thanks.

@PwnCNC 6 ай бұрын

That is an external 20" touchscreen monitor hooked up to the Onefinity BlackBox controller. It's based off from the BuildBotics controller which has an embedded Raspberry Pi installed in kiosk mode to show the web browser and the cnc controllers software. I've used a similar setup with a Raspberry Pi running CNCjs in order to have a similar setup. ( seen here: kzfaq.info/get/bejne/arWqYNh4s7vecqs.html ) Unfortunately no, CM doesn't run on an IPad, however finding a low-cost windows surface might work out well. CM doesn't require a lot of power to run, especially if all you're doing is CM. This would give you a very small dedicated PC for your Shapeoko.

@Bill-gb9kf Жыл бұрын

I noticed that you added the 65mm spindle to you onefinity machine... It is my understanding that there is an issue with spindle/z-axis motor clearance when putting a 65mm spindle on onefinity.... have you figured out a way to overcome that problem?

@PwnCNC Жыл бұрын

Lower the mount, drop spindle into place and hold (don't tighten), raise the mount all the way... then lift the spindle till it bumps into the Z motor mount. Tighten it down right htere. This should be just above the bottom of the Z carriage.

@lancelothunter6815 Жыл бұрын

Awesome! Where do I buy?

@PwnCNC Жыл бұрын

pwncnc.com/search?q=tube+bundle&options%5Bprefix%5D=last

@Z-add Жыл бұрын

Is this a rebranded chinese spindle? First time I'm hearing this delixi branded vfd.

@PwnCNC Жыл бұрын

Yes. However backed by an American small business and built to our specs.

@RockhollowCNCServices Жыл бұрын

Deciding between air and water cooled. Is the air cooled pone to collect dust in the cooling tubes? Just a quick shot of air to keep,it clean I would imagine

@thefilthelement Жыл бұрын

I want to upgrade to the spindle simply for the sound alone. Still speaking in a normal volume with it spinning 2k rpm 🤣

@PwnCNC Жыл бұрын

The noise difference was a huge game-changer for my household. Before i had to stop carving at 8pm when my young boys went to bed... now i'm carving well after midnight and no one is disturbed.

@mikeremillard5414 Жыл бұрын

in your opinion water cooled or air cooled

@PwnCNC Жыл бұрын

If i were carving a lot of metals, i'd consider water-cooled, otherwise i'd save the trouble and go air-cooled with one of our "Body Extenders" a 3d printed piece that extends the main body of the spindle so it works efficiently with spindle mounted boots like our v7.