Upgrade Disc Brakes Tips and Tricks

Рет қаралды 36,644

Autorestomod Manic Mechanic Gasoline Media

2 жыл бұрын

• Ford Spring Compressor...
Disc Brake Install Tips and Tricks
Episode 130 Manic Mechanic
Stainless Steel Brake-USA is a company that rose from the ashes of SSBC. It was bought by enthusiast to bring back the quality brake systems that had been offered before. Because we have a long standing relationship with folks that are now at SSBC-USA, we thought we’d give them a shot at putting brakes on our 1965 Falcon Ranchero.
We give tips on greasing the bearings. We show how to set the bearings. We detail out how to install the kit for trouble free use.
Hey, thanks for watching! We appreciate every view and each subscription!
Tell folks we need them to subscribe!
jford@autorestomod.com
/ gasolinemedia
ssbc-usa.com
Kit we used: A120D for v-8 spindles
Had we stayed I-6 and four lug: A120-4/5
Auto Krafters
Spindle RH Front 1965 Ford Falcon: C5DZ-3105R
www.autokrafters.com/p-23339-...
Spindle LH Front 1965 Ford Falcon: C5DZ-3105L
www.autokrafters.com/p-23338-...

Пікірлер: 76

@BillyAngela-dj4xr 2 күн бұрын

Being a Caterpillar mechanic for 38 years has helped me, I have a 1963 fair lane sports coupe which I installed 1977 Granada spindles and all disc brake parts. Installed dual master cylinder, replummed it and put 1970 LTD tie rod joints. Everything works perfectly!

@williamcharles9480 Жыл бұрын

My dad taught me to apply grease into the hub, also. He was turning wrenches in the 1930s. I also use splash shields on a road car. Pebbles can get lodged between the caliper and rotor without them, including anything else. One can bet that if the factory went to the trouble to engineer splash shields, they should be used. Thanks for the video, Jeff.

@RalphSampson... 2 жыл бұрын

Nope. I put a blob of grease in my hand as you did but, I'll scrape the bearing across the blob until it starts to leave out the opposite side and continue to work my around the whole bearing. This way you KNOW grease is all the way through the bearing.

@irritablearchitect 2 жыл бұрын

The way you describe is the way I learned to do it, probably 40 years ago from my Dad, and I have never had an issue with it.

@REVNUMANEWBERN 2 жыл бұрын

50 years ago my professional Mech Uncle ( in his 70s ) taught me basicially the same, glob in palm, then push the side part of bearing into the blob till you see it coming out the other side

@ShadowWolfIA 2 жыл бұрын

That's how my grandpa taught me

@jeffj1324 2 жыл бұрын

I like this kit for my 1963 Falcon. Thanks for sharing!

@suchite8 2 жыл бұрын

Did you have to change the tire size? I got 14’s and considered this kit but still not sure.

@michaelwelch5392 2 жыл бұрын

I was taught to grease the inside of the hub also. I was told that it helped to cool the bearings or keep the heat from the rotor

@capecodvintagerevival6626 2 жыл бұрын

I've always been taught to clean the rotors like you did, but here's my question, does it really matter? I mean, I understand getting grease off, but finger oils and dust, eventually those brakes will get dirty while driving and rusty, just a philosophical thought! Great video as always!

@Paulie1232 2 жыл бұрын

The Rancho is looking sweet...

@A_Litre_of_Farva 10 ай бұрын

My ‘59 Ford shop manual says to put grease in the hub until it’s level with the race. Great video ❤

@69mustang 2 жыл бұрын

Great video. Thanks a million!!!!!!!

@domfer2540 2 жыл бұрын

Good job. I always hand grease bearings, I prefer hands on. I could not believe the professional you are that you were wearing a ring. No grease on back of brake pad or mounting tab.

@davidhofman4341 2 жыл бұрын

I was a mechanic for a Regional Airline in 1978. We were always replacing bearings due to burn spots on the outer race. When the airplane lands the bearings burn out to get started. The corporate jet for a major candy company was next door. They said they had switch to this new grease by Mobil and that their burnt race problem was gone. We switched and what a difference in bearing life.

@PHCBILL 2 жыл бұрын

Good to see you back "business as usual". Nuther good one, I would put the cap on before cleaning the rotor, isolate the grease as soon as possible.

@AutoRestoMod 2 жыл бұрын

Great point!

@willkuehn6950 2 жыл бұрын

I also have had Mobil 1 grease marking its territory in my tool box drawer.

@brucethoel3636 2 жыл бұрын

I pack it fully from the open cage side to closed cage side to prevent trapping air in the middle

@CopCat34 2 жыл бұрын

Thanks for the video. I would recommend a seal installer. They are very cheap in most automotive store. Glad you are back. Keep those videos coming!!!

@kenbarnes8958 2 жыл бұрын

Just for fun stuff --- On 1965 full size Fords, I installed 220,000 of those seals plus a bunch of other stuff.

@TheVenom8343 2 жыл бұрын

@@kenbarnes8958 How did you do it at the factory? Like what tools and what process did you use? I find that kind of stuff absolutely fascinating!!

@kenbarnes8958 2 жыл бұрын

@@TheVenom8343 --- at the factory they will spend any amount of money that will allow you to complete your job in the alloted time [usually less than a minute] - but was there something in my comment that let you know that I worked on the Ford assembly line in '65?

@TheVenom8343 2 жыл бұрын

@@kenbarnes8958 Yeah, when you said "On 65 Ford full sizes" and "220,000" made me think that you worked on the assembly line. Sorry about that my dude. What kind of work did you do?

@kenbarnes8958 Жыл бұрын

@@TheVenom8343 I installed the bearings, seals and greased them (about 10 seconds each drum) - put them on the spindles - installed the nut and washer and ran them down. Both front drums. I could do all that in 49 seconds. The next guy just adjusted the nut and cotter pined it. Don't sound fair does it?

@bobsue3639 2 жыл бұрын

When you speak of "little dab will do ya" are you speaking of Mobil 1 or Brylcreem? Nostalgia from the good ole days. Great job, love your vids, especially concerning Falcons.

@AutoRestoMod 2 жыл бұрын

Mmmmm yes?

@jeffrob073 2 жыл бұрын

Just mocked up the Ridetech suspension and Street or Track Big spindles and 13x1.25” brake system

@AutoRestoMod 2 жыл бұрын

Nice!

@RalphSampson... 2 жыл бұрын

I have used many different oils and greases. I've never had an issue with any of them. Lube regularly. They are all fine ...IMHO.

@REVNUMANEWBERN 2 жыл бұрын

Take a short piece of 2x4 to lay on seal, then hit the 2x4

@AutoRestoMod 2 жыл бұрын

That can work too, but I find that this works best for me.

@trayhine4578 Жыл бұрын

@autorestomod...have you any information on brake upgrades for the 66 falcon. I haven't seen you do any 66 and later.

@anthonylatronica5108 Жыл бұрын

I have a 64 Falcon Sprint with stock suspension front and rear. I want to put Magnum 500 wheels in either 15 or 17 inch. Do you have a handle on what the maximum tire size and what offset i can use without interference and or rubbing?

@CMOSX 2 жыл бұрын

I’ve been wanting to do the drum to disk for a while. Glad to see there’s another option. How does this kit stand against the CSRP kits in terms of quality?

@REVNUMANEWBERN 2 жыл бұрын

I converted my 65F100 with this companies parts and was satisfied, but I didn't get a complete kit, I used latter truck disc spindles, dust covers etc.

@paulnaiman8108 2 жыл бұрын

The shield is there for road debris and to reduce brake fade when wet

@AutoRestoMod 2 жыл бұрын

Yes.

@stephenhotzjustdriveit 2 жыл бұрын

There is a 3rd style bearing greaser. That is what I use :P

@AutoRestoMod 2 жыл бұрын

That works too.

@timswansson1955 2 жыл бұрын

@autorestomod I see the part numbers for the new spindles in the description, but not which kit you used from SSBC-USA. I see they have a few different kits listed so hoped to see which one you actually used.

@AutoRestoMod 2 жыл бұрын

Sorry about that. I will update the part numbers later today.

@timswansson1955 2 жыл бұрын

@@AutoRestoMod no worries at all. I know you have your hands full with moving, and setting up the new location. So got to take care of that stuff first

@treymarrs6860 2 жыл бұрын

What car did these come on stock,do u have part number

@Onesimus4 2 жыл бұрын

Greasing inside the hub prevents condensation

@mycontinental3611 2 жыл бұрын

I always add grease inside the hub.The brake caliper's look just like the 4 piston calipers that are factory installed on my 68 Continental.I just replaced my calipers and I also installed hydro boost.I bought my car with no engine no transmission and no brake booster.And nobody makes the old booster any more. My brakes are toe touch.

@earlybirdsspeedshop6895 2 жыл бұрын

this kit fit a 64 fairlane ?

@jr_8975 10 ай бұрын

Why is my rotor a 2 piece can I swap it for the one piece in this video

@richardlumb3354 2 жыл бұрын

Does this kit 1963 fairlane?

@voltairegramos Жыл бұрын

Purchased a set of Scott Drake steering spindles and the tapered holes for the Mustang V8 tie rods are too small and increasing the size of a tapered hole is no easy thing...what does one do without the use of the puny tie rod ends which come on 6 cylinder cars?

@AutoRestoMod Жыл бұрын

There are two taper sizes on V8. Try using the pre 1969 V8 tie-rod end. Keep in mind that I have received a 1970 tie rod in a 1968 part numbered box recently.

@paulnaiman8108 2 жыл бұрын

Use a block of wood to assist with seal installation so it does seat it correctly

@AutoRestoMod 2 жыл бұрын

Good point

@jeffj7098 10 ай бұрын

Hey guys, I love your channel I watch a ton of your videos. I had a question about my 63 Futura I’ve been told in other forums that it is a good idea to change the spindle to a 65 mustang model because they’re cheaper and brick conversions are more plentiful. But I’ve also heard that in swapping over the 65 V8 spindle the steering components have to be switched over as well. Could you shed some light on this swap?

@jeffhale2278 3 ай бұрын

I'm not sure about the steering, but you may have issues with suspension. Nothing major, but lots of part swapping. For instance, if your Falcon was originally a 6 cylinder, it will have a smaller lower ball joint than the V8 Mustang uses. You'll also have to change the lower control arm, as the ball joint is made into the arm. I bent the knuckle on a 61 once, and the only replacement I could find was a 63. There was some issue that necessitated using the 63 lower arm, and then the anti-sway bar would fit. Ended up going back to the junkyard for the bar and the other lower arm and knuckle. Had to change all this to use one later- model knuckle. This was over 30 years ago, I don't remember all the details, but there was some minor issues to face. With today's aftermarket parts, you should be able to find everything you need.

@jeffhale2278 3 ай бұрын

* sway bar would not fit...

@kenbarnes8958 2 жыл бұрын

I'm wanting to do my 64 Fastback but I have stock 14" wheels, good whitewalls and excellent 3 bar (expensive) wire wheel covers. It appears that you have to change to 15" wheels to use the disc brakes. I don't want to do that. Anybody know for sure if there is a disc brake kit that will allow me to keep my stock 14" wheels.

@AutoRestoMod 2 жыл бұрын

Nope. We are using the original 14" off of Cam's '65. This is the original type Ford used for the GT, right down to the caliper.

@johnmilner7603 2 жыл бұрын

My non synthetic grease in my gun pees also when it sits. For you 1970 Camaro guys, seating the bearing, From the Camaro Supplement manual. When you spin the rotor, tighten the nut to 12 lbs. ft. torque. Then backoff the nut one flat and insert cotter pin. If the slot and pin hole do not line up, back off the nut an additional 1/2 flat or less as req'd to insert the cotter pin.

@AutoRestoMod 2 жыл бұрын

Good stuff as always John.

@fknows1 2 жыл бұрын

the joys of grease packing wheel bearings lol

@AutoRestoMod 2 жыл бұрын

Blech...I hate it, yet it is a Satisfying venture.

@fknows1 2 жыл бұрын

@@AutoRestoMod I still do that way 48yrs later lol

@ShadowWolfIA 2 жыл бұрын

Man I'm watching all these but I have a 1966 Ranchero and it's harder to find parts for the 66 and 67 than any other Ranchero

@AutoRestoMod 2 жыл бұрын

1966 is a one year only Falcon nose. BUT the stuff for 1966 Fairlane will bolt up. Trim items like dash pads (I have one) and instrument clusters are the biggest problem. You can use seat upholstery carpet and door panels from the Fairlane and no one will know. Auto Krafters is our go to on those parts.

@karlx-1 2 жыл бұрын

Noticed the lighting/color correction and shot quality has been hopped up.

@RealWorldGarage 2 жыл бұрын

How about parts that aren’t available for the Merc Comet, like sheet metal. 🙄 oh my dear lord.

@2WETTWHIPZ 5 ай бұрын

Will this fit on a 66 falcon?

@AutoRestoMod 4 ай бұрын

Yes.

@REVNUMANEWBERN 2 жыл бұрын

That REAR bearing scares me, I have NEVER seen one that loose as an assembly, has to be a CHI NA one like most now

@AutoRestoMod 2 жыл бұрын

Think it will be OK.

@FE428Power 2 жыл бұрын

Why don't they offer a universal proportion valve rather than the adjustable type?

@REVNUMANEWBERN 2 жыл бұрын

I've been told because different pressures are needed to activate the rear brakes drum vs disc and even among products thus an adjustment is best

@FE428Power 2 жыл бұрын

@@REVNUMANEWBERN I've upgraded my 68 Cougar brakes to 2005 mustang GT disc up front, left the rear drums stock, factory booster and master cylinder. I'm using a disc/drum universal proportion valve from summit racing and I think I have the best braking I've ever had, and I've tried many of the conversions.

@paulnaiman8108 2 жыл бұрын

You got it but you keep putting it though the bottom until it comes out of the top of the bearing cage then you don't have to fiddle with it and it's less messy. Good job otherwise.

@AutoRestoMod 2 жыл бұрын

Thanks!