Upgraded burner for the furnace. Beats propane? YES! with graphs & first casting and lettering test

No video

Upgraded burner for the furnace. Beats propane? YES! with graphs & first casting and lettering test

Рет қаралды 150,779

Күн бұрын

I've made a better burner for my DIY home furnace/foundry. My previous burner was 'ok' (quite slow and VERY NOISY)... so i really wanted a better solution... So i made "the little burner that could"! SPOILER ALERT - IT'S BLOOMING AMAZING!
I'm still using Diesel as i don't have a ready supply of used motor or veg oil but i reckon this thing could match any propane burner out there! Its also cheap to run (i do tests to find the costs at the end).
I've binned the siphon nozzle burner and i'm just squirting the diesel neat into a red hot chamber now - no nozzle required! i use a modified Dyson vacuum cleaner as the air supply - it makes an awesome blower!
And you know those damned medals i'm always going on about???... I TRY TO CAST A TEST MEDAL as a proof of concept, and a drafted letter plate too :)
I also do a couple of experiments: How fast can it get hot? and i also work out the cost of running it.
Big thanks must go to the "oil Burner" channel link below, as his video was 100% the inspiration for my one!
INSPIRATION & LINKS:
Oil Burner channel: thank you for letting me use some of your awesome footage. This video was the inspiration for my furnace upgrade:
• 300KW Waste oil burner...
Colin Peck's book: "The Artful Bodger's Iron Casting Waste Oil Furnace"
www.artfulbodge...
colin's waste oil furnace No 1:
• The Artful Bodger's Ir...
Brilliant Tube Joint Pattern Generator:
cq.cx/tubejoin.pl
speed controller
www.amazon.co....
fuel pump
www.ebay.co.uk/...
power supply:
www.amazon.co....
Online Graphing:
plot.ly/

Пікірлер: 194

@glumpy10 5 жыл бұрын

Now that was an attention grabbing intro!! You went the right way with a fuel Pump. Gravity is more trouble than it's worth and the pump gives you much more control and stability. Your fuel flow will vary at those low rates with how much fuel you have in the tank and the resulting lift as well as ambient temp so don't be surprised if you have to tweak it. The burner is good too. You could actually just have a pipe for air and fuel feed going into the furnace and do away with the burner all together. Light your fire in the furnace, add fuel and bring the air and fuel up slowly and it will burn well in the furnace. This will give you more heat and efficency but of course it's working perfectly well the way it is. You can cut your costs by adding used veg oil to your Diesel. With that pump I wouldn't go over 50% unless you are outside and it's hot or if new oil is cheaper than Diesel there you could use that. The castings looked great. Well done! A very interesting vid and I admire your workmanship and attention to detail. Something for me to take from that! :0)

@JulianMakes 5 жыл бұрын

Thank you so much Mr Oil Burner. Your version is awesome! when mine eventually erodes itself due to the extreme heat i might just do that and use just the hughmongous pipe direct in. thanks again for your video!

@erwe1054 Жыл бұрын

подобрать хороший надежный насос для прокачки отработанного масла, чтобы не заклинил от возможно содержащегося в масле мусора.

@garljoens Жыл бұрын

I've been struggling for years with trying to DIY an oil burner for my bronze furnace, and you've inspired me to ducplicate yours as close as possible with my extremely clumsy butterfingers. Thanks so much for the in depth thorough and very fun run down!

@JulianMakes Жыл бұрын

No problem! It’s really quite an easy build, you can do it! Let me know how it goes :)

@eccentrickiwicreative2962 5 жыл бұрын

Hi there. Where this burner is of real benefit is when the furnace is cold. The ability to start up without being super smoky is great. Once the furnace is up to temp, injecting the diesel down the tube with the air and straight into the furnace will have the same effect. A lot of people start their furnaces on gas to heat them up then turn on the oil once it is hot enough to flash the fuel to vapor, if one does this you can achieve the same clean burn. By using the pre burner some energy will be wasted once the furnace is up and running. If you were to make a sleeve for your air tube assembly then you could remove the pre igniter and put the air and fuel tube directly into the furnace when up to temp. Just a few ideas you might want to try anyway. Nice casting by the way.

@alimovahedian4860 Жыл бұрын

It is so important burner practical operations. The safety precautions must be mentioned before starting the process of This technical information. Thanks from all staff for prepare for the process of this technical information.

@eduardodaquiljr1621 Жыл бұрын

I like your design because you can throtle flame by adjusting fuel inlet pressure by way of increasing fuel flow and vice versa.Adjusting fan flow as well regulates well the flame power.More power and congratulations on your research works.

@paulriggs42 5 жыл бұрын

I love your analytical approach and great flames ! The medallion was brilliant, you must be pleased as punch with those results !! Can’t wait to see the next casting !

@JulianMakes 5 жыл бұрын

thank you so much Paul. i did reply earlier but YT brkoe my comment. I love the science me :)

@rescobar8572 Жыл бұрын

OMG THIS WAS AN AMAZING VIDEO!! I laughed so much!! THANK YOU!! I just watched 2 videos, one of a Saturn V rocket and the other of the Artemis rocket. The sound those machines made was incredible! It's the PERFECT sound to fill in when the burner "blasts off"!! 😅

@guachingman 2 жыл бұрын

This was epic, scary and funny in equal parts, congrats, the best is your joy

@Machine_NZ Жыл бұрын

Hi Julian, excellent video, learned a lot. Just subbed and looking forward to future melting/casting projects.... Regards Kevin

@JulianMakes Жыл бұрын

thanks Kevin!

@Mad.Man.Marine 3 жыл бұрын

Man. This is one of the better drip burner videos I’ve seen. And I have watched tons. Lol. It shows (please don’t take offense) that a person without a lot can make a sick burner. Good work. Cheers

@JulianMakes 3 жыл бұрын

Thanks mad man! No offense taken! It’s brilliant :)

@Biokemist-o3k Жыл бұрын

Wow! how did I miss your channel. This is awesome. I have been developing a waste oil heater for my shop that works exactly like a regular oil burner. I believe I am going to use the drip method.

@JulianMakes Жыл бұрын

Welcome John and thanks! It’s a super simple setup. It just needs a little heat to get going. I don’t use wood anymore just a few bits of cloth wetted with some diesel, once the air is gently going it creates enough heat to get going nicely.

@Euronasa Жыл бұрын

Great video!!! I tried this today with a 12 liter diving bottle. Used 100% veggie oil and found it hard to reach operating temperature. I also used propane to preheat the thing. The blow out using propane when litting was quite scary. When I finally got 1 meter high flames I was quite overwhelmed! I think it might be too powerful. When trying to reignite the hot tank using propane I only got explosion 💥 and flameout. Think I will not use propane and just preheat with diesel and wood sticks. And electric pump to control the flow better. Thank you!

@WarGrade 5 жыл бұрын

Hi Julian >Fuel, to make it cheaper, use heating oil (kerosene), shop around and you will get it way cheaper than red diesel. I purchase 1500 lt at a time and it's (give or take) about 42p lt. smallest worthwhile quantity is 105 lt (a steel drum). >Efficiency, If you were to insulate the vaporizing chamber with some ceramic wool or such like, I would imagine your burn will become quicker or & more efficient. At the moment you are loosing heat to the atmosphere, all well and good on a winter day maybe. My foundry temperature only rises 1 or 2 degrees over the course of a 2 hour casting sesion (and yes in the winter I wish it were a lot more). >I have forgotten to weigh a flask a few times over the years & it's always an odd cast (ie not a batch like Martin's) & there was some reason behind it such as a quick cuppa delivery...... >My first ever cast Iron melt was with Colin Peck, I too still have a copy of his book. It is infact a very very simple furnace, once built. >well done on your bottle opener, you piped me to second place (you **%*(&(^ ()*^&^%$& ^$& *&$ *%$&& &$*er :) >Id gladly offer my welding skills (Ha skills that's a joke) if we were a wee bit closer, but I'm sure were some milage apart (SE Kent). >any way's toodle pip old chap & keep the videos coming. Andy.

@JulianMakes 5 жыл бұрын

War Grade haha cheers Andy! Ohh I’d not thought of heating oil, I’ll look into that. Oooh lovely Kent, I know it well, My mum used to live near bethesden. Ahh yeah the insulation is a good plan... but I kind of like the red glow! :)

@WarGrade 5 жыл бұрын

My wife use to police Bethersden years ago! The glow would probably be a nice thing in the winter

@FullModernAlchemist 3 жыл бұрын

This is a fantastic build! How cool!

@SkullyWoodMetal 5 жыл бұрын

That thing works like those pulse jet engines. It is an incredible and scary burner. Nice job.

@JulianMakes 5 жыл бұрын

cheers Skully it's a beast for sure, i dont really run it in "beast mode" much though ;p

@breakit2makeit393 3 жыл бұрын

How have i not seen this before? Awesome video dude its changed my burn big time. Iv been using a tap system on a gravity feed and fine tuning is unbelievably hard.thanks dude

@JulianMakes Жыл бұрын

You are welcome!

@brulinn2757 3 жыл бұрын

I have watched several of these oil burner videos and the crude way of lighting them. It seems that you could wire in a glow plug into the burner to light it. That way you may not have to worry about burning your eyebrows off.

@mp180170 3 жыл бұрын

Brilliant I just love the excitement in your voice it’s like me when things go to plan, great job thanks for sharing liked & subbed 👌🏼

@JulianMakes 3 жыл бұрын

thank you so much Mark!!! :)

@russbilzing5348 3 жыл бұрын

Quite simply outstanding reportage, assembly and thinking. Kudos, sir.

@JulianMakes 3 жыл бұрын

thank you Russ :)

@bkailua1224 3 жыл бұрын

What you have is a crude jet engine. Air goes in front add fuel and get it burning and flame comes out the back. :) No surprise diesel would get you a lot more heat. Propane is just a lot easier to use but makes a lot less heat per pound of fuel.

@luckygen1001 5 жыл бұрын

Great video!!!!! Loved the charts at the end of the video. I now know that you will be melting and pouring iron very shortly. One thing I did see that your oil consumption is a little high, my burner uses 10 liters per hour to melt 14 Kgs of cast iron.

@JulianMakes 5 жыл бұрын

luckygen1001 cheers lucky! Yes I might back off on the fuel a bit, no need to waste it I think :)

@mikeharmon4901 7 ай бұрын

Awesome video! One of the best on the subject I have seen. Great charts and tips. I will be utilizing all of your ideas. I do have a few suggestions that might help. You read how everyone talks about vortex.... Changing the angle of your blower end [ the foundry end] a little upwards and maybe even add a plate to direct the flame in a vortex direction instead of the side of the crucible might help?

@jaycousland9835 3 жыл бұрын

I use pinch dogs to hold cope +drag together,and weight sand if pattern is high in horizontal surface area.It's surprising how many run-outs actually fill out-just when you think you've lost the casting!Cuprostatic pressure about 4 times aluminostatic pressure.

@JulianMakes 3 жыл бұрын

thanks Jay that's a great idea!

@joshmellon390 3 жыл бұрын

The DIY core drill got my sub lol All your drill needs in order to be functional are a few small features ground into the cutting faces. I used to work for a company that made custom drills end mills and form tools, and I would love to show you a couple things. t\Too much for a youtube comment though, I'm not one of those guys haha.

@MeltandCast 5 жыл бұрын

Super video, I really enjoyed watching this. Cheers mate. Thanks for sharing 😃👍👍👍

@JulianMakes 5 жыл бұрын

thank you sir! :)

@samueljackson6188 Жыл бұрын

So basically it’s a jet engine. Might I suggest a spark plug or a pizo. Inserted into the combustion chamber

@matthbva Ай бұрын

I built one of those Artful Bodger burners years ago, and it was terrifyingly hot when it ran well. (But I often struggled to get it to run well.) I hope you ended up lining your burner body with castable refractory.

@kraftsmith2929 5 жыл бұрын

i see you're living with the queen... Haha. Bet she'll be happy with the quieter system :p

@JulianMakes 5 жыл бұрын

KraftSmith omg haha I’ve been waiting for someone to notice!!! Yeah she likes the new one much better :p

@kraftsmith2929 5 жыл бұрын

@@JulianMakes Had a good laugh when I saw that. Nice Easter egg ;)

@seafurymike 5 жыл бұрын

Arduino - would be quite simple to program the arduino to output a specific ramp up voltage/flow for specific materials. Im going to try this burner method on my foundry. Looks like you get good repeatable results and nice high temperatures.

@JulianMakes 5 жыл бұрын

hi ya seafurymike! awesome idea! i'd love to see the results when you make your burner. It really is super easy to use, the fuel pump makes life so easy. co-incidentally i'm playing with an arduino right now at my desk (different project) - interesting idea, definitly doable but i'd be a quite worried that i'd leave it alone too long... and then end up with a burnt down shed!

@windyhillfoundry5940 5 жыл бұрын

I thought you had my old burner there for a second. Great video 👍🏻

@JulianMakes 5 жыл бұрын

cheers Windy Hill :)

@moonolyth 2 жыл бұрын

Just an observation, there is such a tool called an Artist Mouth Atomizer. Fitted just like the oil drip pipe except upside down, to get the paint running you keep the pipes perpendicular to one another (and adjust the "oil" pipe unit in/out) Till you get it automizing properly. The artist would blow on the other larger pipe just like your setup. I realize you are using gravity, but if you did this and used gravity as in your example I think you would get better optimization (You may not get the drip drip drip effect in other words). It would probably work better than having an angle towards the flared end of your Burner. Note: being you are not using an air tank it would not make much of a difference except perhaps the fluctuations. With that said I don't think it needs to be angled.... Just an observation I've had.

@CreakyBlinder 5 жыл бұрын

Amazing as aways Pal , better than last nights how its made not seen anyone blow their eyebrows off on that show not even come close

@JulianMakes 5 жыл бұрын

haha cheers mate :)

@moonolyth 2 жыл бұрын

Congratulations!! Great build Idea, Looks like the fuel burner tank mixer will prematurely burn out... as it turns cheery read.

@garethbaus5471 3 жыл бұрын

I would suggest insulating tank you use to vaporize the fuel so you can get better efficiency, but a couldn't garuntee that the metal wouldn't melt. If you preheat your fuel old fry oil might be a good cheap source of fuel.

@SabcatPrinting 3 жыл бұрын

I might make one of these to keep my van warm.. I can point the jet flame out the side door.

@JulianMakes 3 жыл бұрын

haha omg!

@garethbaus5471 3 жыл бұрын

Seems like it might generate too much heat. What about soaking a roll of fiberglass cloth in the oil and lighting one end like a giant oil lamp?

@sdunca4864 5 жыл бұрын

Bravo mate! Love it! Now I can honestly say I love this burner!

@JulianMakes 5 жыл бұрын

woo hoo! that makes two of us :) i think once the gas bottle has eroded away, just the hughmongus tube should surfice.

@docvencil2222 2 жыл бұрын

I think I have found the three extra pieces you used to regulate your burner, fuel pump, pump regulator, and fan regulator. Now I am probably going to need a hand in wiring it all up. I think I wasted money and bought a siphon nozzle but I intend to use a blower and not a compressor. Thanks for your video. Your links didn't work for me because I am in the USA.

@ayubibrahim8227 2 жыл бұрын

Very nice I hope so you get more video

@JulianMakes 2 жыл бұрын

I will try my best

@survantjames 3 жыл бұрын

Impressive! Thanks for the tip on the notch pattern generator!

@smallcnclathes 5 жыл бұрын

Why does the mixer pot (gas bottle) make me feel most uncomfortable when it glows red hot? Are you using compressed air to blow off you moulds or still using the hand thingy

@JulianMakes 5 жыл бұрын

yeah it's only red hot metal :p yeah the hand thingy went missing - weirdly i think it was "stolen". i'll show the grainy "CCTV" footage in the next video... so i'm using the compressor now (much better) :)

@jpcjpc9713 3 жыл бұрын

Does the gas cylinder dont melt??

@dirtfarmer7472 Жыл бұрын

I know that this video was 2 years ago but I hope that you have been using some hearing protection. That thing is LOUD, like standing behind a jetliner on take off.

@johnrisher3007 Жыл бұрын

Try using an electric leaf blower. Put a reastat to control the speed of the blower. I used used engine oil and the leaf blower and melted about a gallon of aluminum in about 15 minutes

@xb1228 9 ай бұрын

Hey Julian, are you reducing your fuel line from 1/4" to 1/8" copper refrigerator tubing? Or are you using 1/4" copper tubing?

@MichaelMacGyver 4 жыл бұрын

get your hands on a bouncy castle inflator, they're cheap and work great ass forge blowers

@askquestionstrythings 5 жыл бұрын

Very nice upgrade. Too bad about the mold lifting from the hydrostatic pressure. Still great results.

@JulianMakes 5 жыл бұрын

thanks Ask :)

@askquestionstrythings 5 жыл бұрын

@@JulianMakes you are welcome

@4lowdiesel Жыл бұрын

If you insulate the combustion chamber it will transfer more heat into the furnace.

@JulianMakes Жыл бұрын

It’s a good idea Marty.

@4lowdiesel Жыл бұрын

@@JulianMakes just some stuff I learned when I was forced to learn thermodynamics. Overall a great design though and I think I'm going to go with something along these lines for a shop heating furnace. However with my design I'll need the combustion chamber to come apart for cleaning from time to time. Synthetic oil leaves a ton of solids and soot.

@garljoens 9 ай бұрын

Can I ask you a little about the power supply for this fuel pump? I live in the USA and I’m not an electricity guy really so I’m not sure what I need to be looking at for a compatible power supply. You got something with a digital voltage display? Does the amperage need to be of a certain threshold or is it just a direct plug into home power with a dial/potentiometer on it? Thank you!

@JulianMakes 9 ай бұрын

Google ‘variable voltage power supply’ I got one of those. They might say buck boost on them. It’s run from a power brick. Good luck!

@chrisallen9154 3 жыл бұрын

I have no interest in casting but I want to build a casting furnace of this design just to watch it work. Probably give it to somebody who does casting when it is completed.

@Wavy_Gravy Жыл бұрын

A rocket stove forge......my 3 favorite things

@stevelamperta865 3 жыл бұрын

Your pretty lucky ,... You almost got yourself a free shave !!!

@felixmrak6597 3 жыл бұрын

9:00 I would be running for my life

@whydotufaqoff 2 жыл бұрын

Nice video...Thanks...

@Ken-rk3by 3 жыл бұрын

I wonder how many pounds of thrust you could get if you put a 2-inch nozzle on the end of that thing LOL 😂 CRUDE ROCKET ENGINE

@eduardodaquiljr9637 Жыл бұрын

Dear the higher the voltage in pump means more fuel flow so increases in flame intensity?

@JulianMakes Жыл бұрын

Yes exactly. More voltage mean more fuel which means more energy in to the furnace.

@gregarmstrong4653 5 жыл бұрын

That looks horrifying - I love it !

@JulianMakes 5 жыл бұрын

haha it is a bit! i love it too! cheers Greg :)

@gregarmstrong4653 5 жыл бұрын

@@JulianMakes I am sure you can do something with the top flame and the heat from the combustion chamber, maybe a mold pre-heater for investmet cast flasks.

@johnallen8680 4 ай бұрын

The vapouring chamber is getting red hot. Could the interior wall of it be insulated like the furnace to conserve heat and make it touch safe ? Or would the interior of the chamber not get hot enough ? Does the casing glowing red hot play a vital role in the efficiency of the burner ? Great video by the way.

@JulianMakes 4 ай бұрын

Thanks John! I think insulating the chamber would be a good idea, i think it could only help vaporise the diesel more. Not sure about your final question, the diesel needs to be very hot to vaporise well but how hot I don’t know. Thanks for your comment :)

@richardmccann4815 2 жыл бұрын

I like the name 'Numpty'!

@preinstalleduser2309 3 жыл бұрын

I see these DIY burners and wonder why no one has added a a steam generator system to drive the operation.

@othername1000 2 ай бұрын

950 Celsius is roughly equivalent to 7 1/2 fortnights per quid.

@EricScrapping4Dinidog 4 ай бұрын

How do you make the molds? Also interested in the sand casting. Any help would be appreciated

@JulianMakes 4 ай бұрын

Hi Eric! I use a 3d printer to make my molds. As long as there is some side slope (draft) so you can pull it from the sand without breaking the sand, it works well. I like 8% draft but if you are beginning I’d try 15%.

@EricScrapping4Dinidog 4 ай бұрын

@@JulianMakes Okay. Thank You very much!

@docvencil2222 2 жыл бұрын

I am in the USA Your links don't work for me. Can you give me the names of the speed controller, fuel pump, and power supply? Also, can you do a video on the order of how the system goes together?

@josephsturgis6030 3 жыл бұрын

What if you run the air line near the flame to heat it before combining with the oil.

@JulianMakes 3 жыл бұрын

I like the way you think joseph! Unfortunately the flow of air is pretty vast on this blower, the temp would only go up a little if some huge radiator type deal was heating it (i think anyway), also, counter intuitively colder air has more O2 in it (more dense) it more than makes up for its lower temp with a better hotter burn. To be honest this thing throws out so much heat already! I actually need to upgrade it soon, its almost burnt itself to ruin :)

@proteo-x4u 2 жыл бұрын

I have a similar oven but I don't understand why the diesel I put in it is difficult to ignite. I live in Europe, is our diesel different? I don't know! but your diesel ignites rather easily contrary to mine. I am obliged to heat my diesel to bring it to the ignition point before injecting air into the oven. how do you solve this problem?

@JulianMakes 2 жыл бұрын

The diesel must enter a very hot place in order to easily achieve ignition. Im in Europe too. This is why once a small wood fire is lit in the burner chamber, the drips of diesel entering instantly combust. This creates more heat which helps combust the next bit of diesel. Basically heat heat heat.

@proteo-x4u 2 жыл бұрын

@@JulianMakes ok i got it i'm going to make some modifications on mine.thanks a lot julian and continue to amaze us with your realizations

@scottweinberg3268 3 жыл бұрын

After this much time, have you tried waste oil in your pump? Almost anything can variable pump diesel fuel? but clean waste oil?

@charlesbowen3944 3 жыл бұрын

Don't let welding stop you on any project good job

@JulianMakes 3 жыл бұрын

thanks Gomer :)

@alockworkorange7296 3 жыл бұрын

Only one way to get better

@perrychills 5 жыл бұрын

Amazing medals. Please wear gloves and long sleeves while welding. The light given off by the arc is 7x brighter then the sun, it can cause "sun burns" very fast. Very unhealthy for your skin.

@JulianMakes 5 жыл бұрын

cheers Perry, oh i didnt know that thanks i'll try to rememeber that cheers

@perrychills 5 жыл бұрын

@@JulianMakes if you ever need Infos or tips on welding feel free to ask, I use to weld for a living

@adolforamon4575 10 ай бұрын

Sempre aprendendo

@JulianMakes 10 ай бұрын

Sempre!! :)

@juri14111996 3 жыл бұрын

why not get a clicky pump, designet for diesel rv heater?. they can run realy slow.

@JulianMakes 3 жыл бұрын

Ooh i’ll google it, Ive never heard of that. Cheers

@smallcnclathes 5 жыл бұрын

How much draft on the letters?

@JulianMakes 5 жыл бұрын

i think 10 to 12 degrees i can get upto 15degrees but sometimes the software just dies, still at least i found something that works (sort of)! hooray!

@rexhavoc2982 3 жыл бұрын

Did you film the building of the furnace? I need help building one about your size.thanks.-

@JulianMakes 3 жыл бұрын

Yes i did, check out my playlists, one is the furnace build is has several parts :)

@brownh2orat211 8 ай бұрын

Is the pump voltage in metric volts or imperial volts?

@timtelemark907 Жыл бұрын

Hi, Thanks for sharing the informative and entertaining video. What do you think the maximum temperature could be, especially if the air and oil went straight into a well-insulated furnace barrel? Tim

@JulianMakes Жыл бұрын

Thank you! Honestly I think sky’s the limit. If you keep upping the diesel I’m sure it could melt iron if the furnace insulation is good (mine is non existent by the way).

@timtelemark907 Жыл бұрын

@@JulianMakes Thanks Julian, That is very encouraging. I am looking for ~1,500-1,600C for clay fission. I can do it with a wood/charcoal mix, but it is hard to keep the fueling up. Oil should be so much easier. From the look of your furnace chamber's thick wall, I would have thought that it had a lot of insulation? Did you put perlite or vermiculite in the mix as I do? Very funny start to the video. I have had some similar experiences with tiny fan-boosted stick stoves, but have never captured the smoke rings on camera. Tim

@JulianMakes Жыл бұрын

@@timtelemark907 alas no vermiculite or silica blanket or anything! Just solid refractory cement.

@artsseriouschannel 3 жыл бұрын

02-24-2021. Thank you, good luck.

@Bojangles1987 3 жыл бұрын

Really shouldn’t have the fuel so close I mean I’d the burner fell it looked like jt wouldn easily fall right on your fuel tank . Nice build I liked the video I was just thinking about doing thr same exact thing

@smallcnclathes 5 жыл бұрын

19.27, its a lot quieter, as voice trails off in the distance!

@JulianMakes 5 жыл бұрын

haha yeah honestly though it's probbaly half as loud as the old one with the compressor going, i couldnt even talk over that lot going :) i'm having sound issues getting the levels all the same (basically i've been rushing the setting up - but i plan on being a bit more steady and professional with it now so hopefully sound should be better :)

@John-kc7ko 5 жыл бұрын

awesome content! have you considered running the pump at a constant voltage and then using a needle valve to control the flow rate?

@JulianMakes 5 жыл бұрын

i did consider it but as i had to buy a small power supply for the pump anyway i just got the variable supply instead. very pleased i did it works like a dream. i did have a needle valve on my previous iteration of the burner and while it worked it, didnt give me a reliable way to know the exact rate of fuel i'm burning. :)

@docvencil2222 8 ай бұрын

Julian, what connectors do you use on both ends of your propane hose? Do you have Amazon links?

@JulianMakes 8 ай бұрын

hi doc i dont use propane. it's diesel, so it's just fuel hose

@docvencil2222 8 ай бұрын

@@JulianMakes thanks us oil guys use propane to get the chamber going then switch to oil once it heats up

@JulianMakes 8 ай бұрын

@@docvencil2222 ahhh I see!

@docvencil2222 8 ай бұрын

@@JulianMakes the fuel hose information is valuable for that line. I have already ordered the fuel pump for the oil.

@docvencil2222 8 ай бұрын

Here in the USA Diesel is quite expensive, and waste oil is free.@@JulianMakes

@bradfaught1695 3 жыл бұрын

Really good content

@JulianMakes 3 жыл бұрын

Thank you so much Brad :) please sub if you like that kind of thing, im doing more burner building and casting in the new year :)

@andywells397 2 жыл бұрын

Excellent...

@andydelarue9344 5 жыл бұрын

Good stuff well done..Are you going to try use engine oil, that will make it free

@JulianMakes 5 жыл бұрын

Hi Andy, no i dont think so, i dont have a supply of used engine oil or veg oil for that matter :(

@SynKronos 3 жыл бұрын

Now you need consider how you can gasify wood and or coal. ;)

@eduardodaquiljr1621 Жыл бұрын

keep safe

@jbaker7903 2 жыл бұрын

What temperatures were you getting at the different fuel delivery rates?

@AS-ug2vq 2 жыл бұрын

What was the size of input and output tube on that propane tank burner?

@lionelroger626 3 жыл бұрын

Bravo !!!!!!

@Thevwmethod Жыл бұрын

A Chinese 12v nightheater pump would probably work

@itanc1 2 жыл бұрын

love this! we have the same mug! if you are ever in South Wales give me a shout, you'd be most welcome to visit my quite similar workshop!

@JulianMakes 2 жыл бұрын

Oooh I will thank you!!!

@ScottEmmert1980 Жыл бұрын

Very cool video that has earned a sub. I wonder though, why 220v for the fan. Why not 115v? Also, you've really sparked my interest to get a butler suit for my dog as well. MF Cheers and safe melting!!

@JulianMakes Жыл бұрын

haha nice! and thank you! Well in the UK we only have 240V at the houses :)

@ScottEmmert1980 Жыл бұрын

@@JulianMakes Gotcha! That honestly crossed my mind too. Thanks for the quick reply. I can sleep tonight now.

@jamesmartinez991 2 жыл бұрын

Yeah he giggles a lot.

@SuperSodamachine 9 ай бұрын

if yoiu just make the exaust pipe very long, the heat will do all the work for ya instead of the airpump

@JulianMakes 8 ай бұрын

interesting idea!

@andrewdegozaru74 2 жыл бұрын

Nice job. Please don't stand in front of / peer into either end.

@SynKronos 3 жыл бұрын

Na. Use old fridge compressors to pressurise the oil ;) Oh dont give Dyson any credit. They are Panasonic motors ;)

@ParsMaker 3 жыл бұрын

interesting

@dudefromkeene Жыл бұрын

if you suck at welding try using a tig welder. it is more forgiving than stick

@pro.empire 2 күн бұрын

What's the temperature this goes up to??

@JulianMakes Күн бұрын

i can comfortably melt bronzes maybe 1200 C

@pro.empire Күн бұрын

@@JulianMakes how can I get it to 2000 c

@alockworkorange7296 3 жыл бұрын

Rc car fuel pumps may have been closer to the size ud want

@JulianMakes 3 жыл бұрын

Ooooh GREAT idea! Thanks!

@1972Russianwolf 7 ай бұрын

Wonder what the trust is, its basically a jet engine.

@happydays454 3 жыл бұрын

Nice build i need a mig welder with gas your weld will be way better dude

@docvencil2222 2 жыл бұрын

Can you go a little slower and explain your new burner. I got lost when you added in the pump and voltage regulator. I am not technical at all so you'll have to speak slowly.