How To Change And Bleed 🛠🏍 Front KTM Brembo Brakes

How To Change And Bleed 🛠🏍 Front KTM Brembo Brakes | Replace Brake Pads and Brake Fluid

Рет қаралды 46,774

4 жыл бұрын

Check out our line of Enduro Helmet chin mounts for action cameras - shop.wannabes.life
In this video we are going to be changing the front Brembo brake pads on a 2010 KTM 300 xcw. This process is the same across the board for most KTM and Husqvarna years and models. We will also go over how to bleed the brake fluid through the brake system to flush out the old brake fluid and any bubbles that might have got into the brake line. This is a relatively simple process that is easy to do with some basic hand tools. There are a few tricks that will make your life easier and we will go over those in the video. It is very important when you are bleeding the brakes that you make sure to not get any air in the brake system, by keeping the reservoir full of brake fluid, otherwise you will have a bigger project on you hands than you had bargained for.

Пікірлер: 47

@delinquense 3 жыл бұрын

I've watched a ton of these vids for ... I think yours was the best. You paid a lot of attention to detail, especially on the brake lever compression / release instructions.

@ExtremeSportsWannaBes 3 жыл бұрын

Thanks! Glad it helped. We try to make our videos useful

@patl4747 10 ай бұрын

When change fluid you can always empty the the reservoir first with a syringe

@ralphreynolds4803 7 ай бұрын

I use a (reusable) cable tie to temporarily/repeatedly hold the lever in. Time consuming, true, but if you have no help, it works.

@paulpetarson1724 Ай бұрын

a zip tie set so you can slip it on or off as needed and tat works too

@ShiftGearsMoto 3 жыл бұрын

Just randomly stumbled across this. Really nice video!

@ExtremeSportsWannaBes 3 жыл бұрын

Thanks!

@dylanjames4537 25 күн бұрын

Good video, i will add that the anti rattle plates and clips inside the caliper need attention paid to them tou didn't explain what they do or where they are located in the caliper and what thier function is, if the clips and anti rattle plates are too loose the pads knock around in service

@mixtips637 2 жыл бұрын

Very help full I bled brake before but not a brembo

@ExtremeSportsWannaBes 2 жыл бұрын

Awesome, glad we could help!

@xrv_world_explorer2k207 2 жыл бұрын

Hello i have two question , which diametre disc have??? And i want a link for the disc protector

@roccit 3 жыл бұрын

Thanks man, just what I needed!!

@ExtremeSportsWannaBes 3 жыл бұрын

Super glad to hear it. Did you run into any specific issues? It's usually pretty straight forward, but sometimes things can crop up.

@delinquense 3 жыл бұрын

Can you put a link in the description for the extra set of hands? They were really cute.

@ExtremeSportsWannaBes 3 жыл бұрын

Haha those are hard to come by

@raynunez9031 2 жыл бұрын

hello I have a Ktm 690 love 2020. and I would like you to help me I have to change the front and rear fronts I have never done it I have searched for tutorials on KZfaq I cannot find for this motorcycle in specific it is simple I changed the pins oh you have to bleed the liquid from brakes ?

@ExtremeSportsWannaBes 2 жыл бұрын

We've never worked on a 690 unfortunately.

@raynunez9031 2 жыл бұрын

Thanks

@techsmart9475 2 жыл бұрын

Please help me I have a 2017 ktm sxf 450 and I was taking apart the front brake and unscrewed just the brake cable attached to the master brake cylinder and now I can’t get it to go stiff it’s got fluid but I just cant get it to go stiff and work

@ExtremeSportsWannaBes 2 жыл бұрын

It takes a long time and many repetitions to bleed motorcycle brakes. I'd say keep at it, they should firm up eventually.

@braydenwitt7361 Жыл бұрын

@@ExtremeSportsWannaBes I have the same problem and have been trying to get them to work for a week now but still have got no pressure in the lever it just goes straight to the bars

@ExtremeSportsWannaBes Жыл бұрын

@@braydenwitt7361 so we did a video on back bleeding brakes where you push brake fluid through the system from the caliper end. It pushes the bubbles out and it’s a lot faster. That will probably help you more than this video.

@punyetangpantra Жыл бұрын

I almost empty my fluid still not functioning well its still soft when i hit the brakes😞

@patl4747 10 ай бұрын

You would need to fill the reservoir again, if still soft need to remove bubbles

@Rumpl4Skyn 2 жыл бұрын

How do you know when you're done bleeding it?

@ExtremeSportsWannaBes 2 жыл бұрын

The biggest thing is to make sure the lever is firm. If you can pull it in to the handlebars it probably still has air in the line. If you’re just replacing the fluid then just push enough fluid through till it comes out clear. If you have bubbles coming out you need to keep going.

@Rumpl4Skyn 2 жыл бұрын

@@ExtremeSportsWannaBes thanks man!

@JeffMerrill-gn2lr Жыл бұрын

My brakes won't work. They keep locking up. You can bleed them but the pressure remains and only builds the more you squeeze the brake. Over these brakes

@ExtremeSportsWannaBes Жыл бұрын

I’ve never run into that. My guess would be something is blocking fluid from returning or something is mechanically binding the pads or caliper.

@JoshStreetDesign Жыл бұрын

You left too much fluid in that reservoir. I did the same thing once an the fluid boiled, expanded too much and blew out the caliper seals, locked the brakes up, pretty much ruined everything.

@billschafer4087 Жыл бұрын

Brembros accually just fuggin suck.

@ryanolson5605 3 ай бұрын

Yes, if it's overfilled the brake could lock up when the fluid heats up.

@hrsey71 2 жыл бұрын

with my brakes, i have tried to bleed them several times now and no matter what i do, the lever pumps and pumps and never gets firm. the caliper doesnt even move. did i suck air into the line? and if so how do i fix it?

@ExtremeSportsWannaBes 2 жыл бұрын

If you're bleeding them right (meaning you're careful not to let air in each time) then keep going. It can feel like forever until all the air is out. We also have a video up on how to speed up the process by back bleeding the system.

@ExtremeSportsWannaBes 2 жыл бұрын

kzfaq.info/get/bejne/rN6oe7WQtM3NiYE.html

@hrsey71 2 жыл бұрын

@@ExtremeSportsWannaBes will air get sucked in through the motion pro bleeder? thats the only spot i can think of that would let air in. i did notice it drips brake fluid when i open the bleeder.

@ExtremeSportsWannaBes 2 жыл бұрын

Air won't really get sucked in unless you actuate the lever with the bleeder open or let air in from the reservoir. But these master cylinders don't move very much fluid at a time, so it can take a while to bleed them.

@jonthepiano 3 жыл бұрын

you put the lid on backwards !

@ExtremeSportsWannaBes 3 жыл бұрын

Of course I caught that only after I stopped recording 🙄 what can you do

@jonthepiano 3 жыл бұрын

mines dragging i think i need to clean the piston seals

@jonthepiano 3 жыл бұрын

after seeing how easily you lever the pistons in mine are way too tight

@ExtremeSportsWannaBes 3 жыл бұрын

It shouldn’t be too hard to pull the lever. Have you tried replacing the seals on the master cylinder? Usually it’s not a problem unless they are leaking but I’m not sure why else it would be difficult to pull in the lever

@jonthepiano 3 жыл бұрын

i mean when you leaver the caliper pistons in with a screwdriver against the pads. i had to use a G clamp to push them in. i’ve flushed the fluid and cleaned and greased the sliders. the pads are a bit old but not so old. i will try cleaning seal grooves out and if they look bad or won’t fit back in i guess it’s because they are swollen from contamination and will order new. and new pads while i’m there.