Warmaster 3D Printing Experience

No video

Warmaster 3D Printing Experience - Wood Elves

Рет қаралды 8,693

WarHQ

Күн бұрын

Пікірлер: 28

@Commander_Applejack Жыл бұрын

6:54 - That poor horse is missing a leg.

@tylerttinsley 3 жыл бұрын

I love these miniatures! And I love my sonic mini 4K.

@warhq 3 жыл бұрын

Same here!

@Pinchy-wj5em 3 жыл бұрын

They look sick

@warhq 3 жыл бұрын

Thanks mate

@BBrecht 2 жыл бұрын

The detail on these is great! If you'd said they were 15mm I'd have believed it.

@warhq 2 жыл бұрын

Indeed

@mackbolan1733 3 жыл бұрын

Very enjoyable video, thanks for sharing. I have these stl's as well and have printed some of them (I print only what I am ready to paint) and they are indeed fantastic models...the Centaur model is supposed to be Orion, King of the Woods...I wish he had two legs rather than the four though, like the original GW model. I actually am a Patreon of Forest Dragon, so have all his stuff, as well as stuff from a few other 10mm sculptors...10mm Fantasy has exploded in the last year, especially in the last 3-4 months...there are several high quality sculptors doing fantastic models...I reckon wthin a year or so from now we will have the entire collection of Warmaster armies available for purchase as high quality stl models. I play Warmaster, but I think I prefer the rules for Fantastic Battles... I have the Phrozen Sonic 4K, which is a similar machine to the Phrozen Sonic Mini 4k and just like your machine, mine does a really good job of printing out these minis. What resin have you been using? I find it is a little difficult to get access to a good range of resin here in Australia...

@warhq 3 жыл бұрын

I have been using the 4k Phrozen grey resin designed for the machine, works a treat. 10mm is just such a great scale, it's fun to print and play mass battles. Thanks for watching. Much more 10mm content incoming.

@naomih8942 3 жыл бұрын

Sweet sweet resin

@warhq 3 жыл бұрын

Resin crack?

@naomih8942 3 жыл бұрын

Yes lots of resin crack

@warhq 3 жыл бұрын

@@naomih8942 seriously.....lots of resin crack

@skheel8188 3 жыл бұрын

Looks fantastic, love this content. Do you have any plans for some Warmaster content? It would be fun to see 2 different armies kinda grown from scratch

@warhq 3 жыл бұрын

For sure, already started the 2nd one

@tankatim13 Жыл бұрын

Got myself the bretonians and printed a 10,000 pt army ... now i just have to paint them.

@terratorment2940 2 жыл бұрын

The main problem I'm having is getting them off the build plate without breaking them

@warhq 2 жыл бұрын

Try a wham bam build plate

@MH-ix3zh 2 жыл бұрын

When you set up your print bed did you use supports directly under them and raise them a few MM off the print bed. Or were they directly touching the print bed?

@warhq 2 жыл бұрын

Touching the print bed on the infantry. Angled and raised with irregular minis

@MH-ix3zh 2 жыл бұрын

@@warhq It may be worth putting some images of your print bed set ups for each unit or most of them in your videos. It is directly related to your experience printing these models and would be helpful information.

@geeksworkshop 3 жыл бұрын

I just got a Phrozen Sonic Mini 4k and a bottle of the 4k resin are tips on the settings? Do you fill the build plate to maximum capacity and clean the resin after each use?

@warhq 3 жыл бұрын

Awesome, they are a great machine. I used the settings that are listed in the manual that comes with the machine, which were slightly different then the standard Chitubox settings I noticed. I cram as much onto the build plate as I can. If not perfectly Z leveled you can sometimes get non stick on the extreme sides, and also if you use supports that are too light for the weight of the model you are attempting to print. I have had a lot of errors, but I would say they were 100% my fault.