One tip, running the engine up to temperature before draining the oil will help with drain it faster/completely. Good diy video!
@1SpudNuts1BigNasty-DIY4 күн бұрын
Yes, that is good advise!
@volunteeraerialspecialists52745 күн бұрын
Couldn't you have powered the dig quads with the 12 volt power then take 5 volts from it to the relays?
@1SpudNuts1BigNasty-DIY5 күн бұрын
There is no 5v output from the DigQuad. Take a look at this video of the wiring diagram. kzfaq.info/get/bejne/oJihY6qn0pumon0.htmlsi=gCX7SHT-C1WjUYUs
@fosterb24714 күн бұрын
It's great you had a go fixing this old tape machine - Tape Apes will chatter but you are a 'class man' for doing a good job on these difficult machines. Well done sir... 🤓
@JohnS-um3lm18 күн бұрын
Didn’t work for me. I can’t get it to do the engineer mode
@1SpudNuts1BigNasty-DIY16 күн бұрын
Yeah, it can be difficult.
@trulsdirio20 күн бұрын
If you fill the whole plate you can get quite a bit done for a two minute change. Nice!
@1SpudNuts1BigNasty-DIY20 күн бұрын
This was just a test but yes, I’m could file the plate, I could do a lot of items at one with.
@robertshanks367420 күн бұрын
Hi, I am having an issue with my 1506 that is driving me nuts...do you service the deck or can you recommend someone?? thank you
@1SpudNuts1BigNasty-DIY20 күн бұрын
Sorry, I don’t service any and finding someone is really hard. I would do a google search for “vintage electronics repair” in your area to see if there’s someone that can help.
@raymond983921 күн бұрын
Thank you, this is the best explanation YOU MUST use something solid to push with. Took less than 3 mins Thank-you
@mxcollin9526 күн бұрын
Good stuff thanks for posting.
@thatguysalbbl327029 күн бұрын
You showed nothing in terms of the actual replacing.
@f37_59Ай бұрын
Thank you King you saved me 🤞🏽
@johnmdavis999Ай бұрын
Super helpful. Thank you!
@naturaljah100Ай бұрын
How did you attach it to the soffit ?
@1SpudNuts1BigNasty-DIYАй бұрын
Each J channel has a side with open slots for screws. You just put that edge against the inside of the fascia and I just used 3 screws for each section. Look at the other videos in the playlist. There’s a bunch!
@naturaljah100Ай бұрын
Sorry for bothering you. I purchased a different jig and couldn’t get it to work . Is it possible to get your specs to make one like yours?
@1SpudNuts1BigNasty-DIYАй бұрын
@@naturaljah100It’s ok but I really don’t have any plans for it. I took some 1 x 2 pieces of wood, laid them around a piece of J Channel and built the track. Then drilled the hole for at end (same size as the bulb (12mm). I then measured back 2.5” and put the dowel. The issue is that I had to sand down the dowel to 12mm because I couldn’t find one that size.
@naturaljah100Ай бұрын
Thanks so much. You are just awesome .
@hesedkenАй бұрын
have one i will sell you
@geonimanАй бұрын
Genius! Saved my life. Thank you so much.
@tundrastorm4648Ай бұрын
Whats the name of that tool that goes into the adjustment knob?
@1SpudNuts1BigNasty-DIYАй бұрын
It’s a 6mm hex bit.
@barryhesford3130Ай бұрын
Looks a great solution but mine doesn't behave! I don't think my OPEN button slides down as much as yours so all the number buttons are totally resistant to any pressure. Any further ideas please?
@1SpudNuts1BigNasty-DIYАй бұрын
Spray some WD40 on all the buttons to loosen them up and try again.
@DjStiv3Ай бұрын
Wont work for me. Dont feel sht
@TheArtOfReSelling12 ай бұрын
who sells the Miracle Paint other than MS, I was wondering if its available locally.
@1SpudNuts1BigNasty-DIY2 ай бұрын
The link is in the video description.
@lg90622 ай бұрын
Thank you!!
@charlesraymond53022 ай бұрын
*promo sm*
@coxbr12 ай бұрын
I like your video the only problem is that you didn’t tell me how to set the new combo, but that is what I need to do. My lock is brand new but no instructions how to set the combo. This is the closest I got to get any answers. Thank you in advance.
@1SpudNuts1BigNasty-DIY2 ай бұрын
The video does say how to set the combo, you just remove the card and turn the screw for what numbers you want.
@kbun132 ай бұрын
only 2 buttons pushed down? now what??
@1SpudNuts1BigNasty-DIY2 ай бұрын
Try to spray some WD40 on the buttons to loosen them up.
@jimon12872 ай бұрын
Excellent video for replacing dial and lock. Thank you.
@josephl67882 ай бұрын
Need help. I dont feel thebpush back even if I press hard on the buttons. I do feel a couple of numbers but they dont work
@1SpudNuts1BigNasty-DIY2 ай бұрын
Spray some WD40 on the buttons to loosen things up.
@josephl678810 күн бұрын
@@1SpudNuts1BigNasty-DIY Tried WD40 and still unsucessful.
@DevonsWorkshop2 ай бұрын
The component that fried is a surface mount resistor. It's the same style as the R250 resistor beside it. The value is almost readable through the gray ash. It's the same as a normal through hole resistor just pcb surface mounted. Looks like trace J5-5 got overloaded somehow. 2 resistors right next to each other like that is usually a voltage divider that steps down the voltage but it can only handle a certain amount. Therefore it likely was overvolted somehow and blew the resistor divider. Lightning strike?
@1SpudNuts1BigNasty-DIY2 ай бұрын
It’s possible but don’t recall any storm. It could have been the solenoid that died, it could have shorted.
@Anna-en8in2 ай бұрын
Thank you! Worth the time it took me as it contained a key to the front door of our new house 😳😅
@TMommat2 ай бұрын
Gonna try😢
@1SpudNuts1BigNasty-DIY2 ай бұрын
Yes, definitely.
@elchinguengenchon2 ай бұрын
Hi, did you notice a difference? The engine sound good!
@MrFreerideForever3 ай бұрын
2k subs, 120k views. 😄
@stay4theride3 ай бұрын
I just got a 3.5 inch lift. So I guess I should lower the headlights 4 inches just to be safe. I also feel like it’s not eliminating the asphalt as much after the lift.
@bigerat-vq6fw3 ай бұрын
What do you do when reset button won’t work?
@1SpudNuts1BigNasty-DIY3 ай бұрын
There’s nothing you can do. If you can’t reset it, it’s would be difficult to push in the combo.
@Dpinks75223 ай бұрын
I have a 6 month old Whjirlpool oven and it doesn't work like that.
@1SpudNuts1BigNasty-DIY3 ай бұрын
See if there is a “menu” or “settings” option. Newer models have a settings menu that you have to go through.
@michaeldeloso90423 ай бұрын
Good day Sir 👋 I created a playlist with different preset inside of the playlist I've made but it's not playing or changing preset that is included on the playlist I've made
@1SpudNuts1BigNasty-DIY3 ай бұрын
You need to make sure your segments are saved with each preset. If not, then it will keep resetting when you try to play your playlist.
@tbcoachniblick12083 ай бұрын
Is it a secret what caliber ..??
@1SpudNuts1BigNasty-DIY3 ай бұрын
It’s a .32 caliber.
@tbcoachniblick12083 ай бұрын
The rifle on a nice lighter surface ( blanket maybe) would enhance the viewers watching experience ...!
@drifterdogs3 ай бұрын
The words you used to explain the pressure feedback on the opener slide solved this for me!!! All of the buttons were "tight" but not all of them would push back on the slider when tight.!! Thank you!
@adamm19023 ай бұрын
Thanks! Replacing mine this weekend and this really helped!
@kevinpond22013 ай бұрын
Really? No follow up on if it was enough? Some influencer you turned out to be. Jk thanks for the info
@1SpudNuts1BigNasty-DIY3 ай бұрын
Well, the simple answer is that no one is flashing their high beams anymore.
@why67953 ай бұрын
Fixed it!😅
@user-em7jh4nd9k3 ай бұрын
ATTENTION before doing this on the doorman replacement and breaking it please file down that tab with a round file and it will slip right in. Been there broke two of them
@bryana41732 ай бұрын
Thank you for the tip. I did not have a file, but a drill bit worked just as good.
@qalih3 ай бұрын
Can't tell you how many times I referred to this diagram for my own setup, thank you. Ended up splitting the 230 AC power and getting a second 5v PSU to power the relay. Main reason to get a relay was the 12v meanwell PSU had horrible coil whine and this solves it.
@hectormuzquiz52774 ай бұрын
Thank you! You have show me how to do it, finally! Good job.
@LaDolceVida_Maui4 ай бұрын
OMG! How easy it is to hack these boxes - I'll never use one again!!!!! Thanks for the info.
@qalih4 ай бұрын
Interesting stuff, this has given me the idea on how best to switch on and off my lights. So did yours work? The timings and the hack to run it longer?
@1SpudNuts1BigNasty-DIY4 ай бұрын
Yes, it works perfectly.
@davekohn60494 ай бұрын
Hot, neutral and ground. Neutral is not a common
@capthowdy1264 ай бұрын
where did u get that phone holder on ur p1p, i was getting ready to print one that i found on makerworld but its not near as nice looking as the one u have in the video, would love to try it myself if u have a link or name for the file.
@1SpudNuts1BigNasty-DIY4 ай бұрын
There’s a bunch available, search printables and Thingiverse too.
@timeinthefield4 ай бұрын
I am a licensed locksmith and I encounter these often. Many times the customer forgot the combination. Now instead of having to destroy the box to get the key I can use this trick. I actually had a few laying around in my shop with no known combo and I was able to open them using this trick. Worked perfectly. Thank you!
@owensieber15774 ай бұрын
Great video, as I was watching I saw you had a stand for what appears to be a very old Iphone, probably 6 or 7. Using it for handy. what a great idea. I happen to have an old 6 that will work just fine. Would you be able tp point me in the right direction to get the files to make that cool phone enclosure? thanks again for the great video!
@1SpudNuts1BigNasty-DIY4 ай бұрын
Here’s the link to the mount: makerworld.com/en/models/66386#profileId-69709 But I’ve changed since this video to the XTouch screen. Just Google it, it’s pretty nice.
@DonnaHolliman664 ай бұрын
Thank you so much this fixed the problem I was having 😁