Пікірлер
@REL3712 6 күн бұрын
Excellent video. Detailed and explained briefly & clearly, & concisely. My first ever diesel and am learning a ton. Thanks!
@CaseyBoykin 6 күн бұрын
You did not show it on your video but what do you do with the other line coming off of the reservoir tank
@pusherintakes Күн бұрын
It varies by model year of the truck; that line exists only on 2013+ model year trucks and gets capped where it joins to the coolant tank. The line from the top of the radiator to the tank handles any purging that needs to happen in the cooling system.
@BuildingByFaith 8 күн бұрын
Great install video. I'm planning on getting one of your kits, either the one you show here with your filter or the one that works with the stock filter and getting a Banks ram air. Do you have any air temp and density data for your airbox?
@registrationhater 9 күн бұрын
Too bad this isn't available for the 11-16 trucks
@pusherintakes 8 күн бұрын
You are correct that it is not available on 2011-14 trucks (with the stock GT32 SST turbo). However, the 15-16 trucks are good to go with the Powerflow, as well as any 11-14 trucks that have an aftermarket 15 or 17+ style turbo. Call us if you have any questions on that! 772.212.9290
@Japatree03 14 күн бұрын
What about the 11-14 years?
@P2WOfficialYoutube 17 күн бұрын
(THE COOLANT DRAIN TO THE RESIVOIR GETS A PLUG NOT SHOWN IN VIDEO BUT COMES WITH THE KIT)
@FinkFarm2011 17 күн бұрын
Do you sell the EGR delete as well?
@pusherintakes 16 күн бұрын
Hi, no, we don't - this system is for race trucks that are already tuned for off-road use.
@jwalsh504 20 күн бұрын
You're videos are the best. Very informative and detailed. I will be calling you guys next week and buying the upper intake/turbo inlet combo and the hot and cold side tubes. Great looking products and excellent presentation. Thanks!
@chadalpert8273 21 күн бұрын
Great looking system. I just had to replace my cold side pipe after it ripped. With 80,000 miles, I could not believe the carbon buildup I had caked in the EGR part of the throttle body/intake area. I get how it the stock EGR area could clog with the poor airflow and areas for it to accumulate. Based on your testing, does your system flowing the EGR in a smoother area closer to the intake will this cause that carbon buildup more into the engine area or does the engine burn it off more efficiently?
@Codysduck 28 күн бұрын
31-July-2024 anyone considering this kit - it's great, but the airbox they provide is shit .. the rubber gasket they provide was not heat cycled and it comes apart leaving a gap in the airbox and the airbox clips coming undone making it rattle . Pusher has known about this for years and there is still no fix ... proceed with your own discretion
@MrBoyRc 28 күн бұрын
Why don’t yall weld a bracket on y pipe for the dip stick mount
@pusherintakes 22 күн бұрын
We do, we must have missed filming that part of the install, but you can see the bracket while the manifold is on the table around 11:20
@gabriellucio5439 12 күн бұрын
It doesn’t show where the trans dip stick tube bolts up?
@cumminsincI6 Ай бұрын
And what of the hose on the back of the head?…
@lanehammer Ай бұрын
On my priority list..
@nombr Ай бұрын
Looks sweet, I have an inter cooler pipe from pusher on my 16, if I get this kit would that still fit or do I need a longer hot side pipe?
@pusherintakes Ай бұрын
It'll still fit! Our charge pipes and the Powerflow are all modular upgrades.
@MYLOVEISTHEBESTTOME Ай бұрын
AS A TECH I WANT TO KNOW . WHO HAS PUT THIS ON AND TORE THERE ENGINE DOWN TO SEE SOOT BUILD UP IN INTAKE RUNNER AND AND VALVES AFTER 30 TO 50 K . RUNNING FACTORY EMISSIONS THE EGR SOOT IS NO LONGER GET ACCUMILATED IN THE FORWARD SPOT ON FACTORY INTAKE WOULD LIKE TO SEE PICTURES OF IT
@MrBoyRc Ай бұрын
Should have removed turbo silencer makes truck sound like a jet
@andrewsolis2988 Ай бұрын
Just an FYI I have a 24 HO and my turbo coolant lines run over 1/3 of the intake, had to remove the fuel filter housing and come out from the drivers side
@akrider174 Ай бұрын
What happens to the coolant bottle hose that was connected to?
@akrider174 19 күн бұрын
Never mind he did not show all of the install. It’s cut short and has a plug.. this would be good to know
@P2WOfficialYoutube 17 күн бұрын
@@akrider174thank you for pointing that out.
@larryphillips4164 Ай бұрын
Don’t buy the K&N cold charge pipe kit, it’s bs. They trying to save money by not making the little rubber elbow piece too short by 1/2” and the metal clamps are 1/2” too short as well. Fucking hell cmon K&N. I’ll give you $5 more dollars to not make this shit a struggle fest!!!
@nabielsuleiman7039 Ай бұрын
Does it come in different colors
@user-rq2yk3rr6v Ай бұрын
Way different than my 15 and 16!!! Intake removal
@user-rq2yk3rr6v Ай бұрын
Nice very very nice 👍
@mxracer158 Ай бұрын
Just ordered mine, looking forward to installing it..
@victornunez8522 Ай бұрын
Anybody here have this style manifold on their 2011-2014 6.7 powerstroke? I have a 2012 and want to see if it will fit. Thanks!
@victornunez8522 Ай бұрын
Does this style not fit a 2012 6.7 powerstroke? Im not too familiar with what changes on the 2015+
@pusherintakes Ай бұрын
This is not compatible with the stock 2011-2014 dual-inlet turbo. In 2015 Ford changed the stock turbo to a single inlet, and raised the pedestal up higher. Owners with 11-14 models who choose to upgrade their turbo to a 2015+ turbocharger / pedestal are able to use this system.
@mikemike827 Ай бұрын
Anyone seeing better miles per gallon?
@jaydoubleu101 2 ай бұрын
Why use crappy gear clamps instead of Oetiker clamps (permanent) or constant pressure spring clamps (removable)?
@Abacogardens 2 ай бұрын
awesome! 💪
@williamsantiago7303 2 ай бұрын
Does this kit have ANY Chinese made parts in it?
@pusherintakes 2 ай бұрын
The only components that may be Chinese would be hardware (nuts, bolts, gaskets, etc). All of our major components (steel, aluminum, clamps - also engineering, fabrication and support) are USA, and our heavy-duty silicone couplers are made in Mexico. And while we're proud to say Made in the USA, please keep in mind that being made in another country does not inherently make a product a bad choice - being made for cheap does. We take pride in our material sourcing and choices and it's reflected in our product pricing.
@williamsantiago7303 2 ай бұрын
I just saw a video where a customer was complaining how this kit doesn't fit like it suppose to and he showed several Chinese parts in this kit. I was considering this kit, but after what I saw, I'm not dealing with that. I'm tired of forking over my dollar too China.
@pusherintakes 2 ай бұрын
Our steel is USA steel, our designs are USA, our production is USA, our stainless t-bolt clamps are USA. Our silicone couplers are made in Mexico, and they are super heavy duty / commercial grade and we have no problemo with supporting our neighboring country. Our machined parts are USA steel and aluminum, from USA suppliers. If the video you watched had a complaint, siting the cause as "made in China" would not be the origin of the cause. If you'd like our response to the video, just send us the link so we can let you know our thoughts on when / how that install went wrong.
@vincer8691 2 ай бұрын
Do you have any dyno before and after videos?
@pusherintakes 2 ай бұрын
Unfortunately not. We choose to just show flow-testing data on our products so the comparison against stock can be apples to apples and super precise.
@TONYCARROLL-mm3lu 2 ай бұрын
BTW was it a safety wire tail or an angle cut zip tie that cut ya ? the old Pipers were tied with a string like material best i remember that was before zip ties tho
@pusherintakes 2 ай бұрын
Can't remember this specific day, but it seems every part of the stock Powerstroke is out to get you sometimes.
@TONYCARROLL-mm3lu 2 ай бұрын
love the bandaid ! im also a fellow aircraft mechanic, and former IA, self employed then and run a 95% Ford diesel shop her in east Tn, I figured a daughter had fixed your finger up lol im fixing to order a bunch of stuff from you for my '16 f350, and hope to get a good association started so i can pass on to my customers
@pusherintakes 2 ай бұрын
Awesome, shoot us an email at info @ pusherintakes.com and we can get you some distributor paperwork if you like what you see after you get your goodies for your F350.
@BetweentheCheeks00 3 ай бұрын
Is the stock throttle valve gasket non-reusable?
@pusherintakes 3 ай бұрын
The stock gasket is more of a one time use item. The o-ring we supply can be reused if you ever unbolt the throttle valve replacement.
@spartanoverlanding300 3 ай бұрын
Just got my set for my 18, now I just need to find the time to put them in…. Need a sick day from work I think…
@pat9125 3 ай бұрын
Installed this along with the cold side pipe into my 2024 Platinum Tremor. I can't say enough good things about this product. One of the missed benefits is how the stock unit runs the EGR into the throttle body. THis setup should prevent the coking issue some have had. I paired it with a Banks big arse filter and finished it off with the banks DPF back exhaust. I don't have before numbers as the truck is new but my EGRs towing, power and mpg are fantastic!!! Thank you for this product.
@pusherintakes 3 ай бұрын
Thank you for taking the time to share your review! Much appreciated 🤘
@17thRodeo 3 ай бұрын
so how do you start it on cold mornings
@fredsamtrucking 3 ай бұрын
I noticed you guys deleted the crankcase filter as well any error codes for doing the delete????
@fredsamtrucking 3 ай бұрын
Do you get any error codes doing the delete??
@armandomaldonado1559 4 ай бұрын
How much does this cost and where do I order it?I would love a kit
@pusherintakes 3 ай бұрын
With powder coat they are $1,175.00 - you can view and order them here: 2015-2019 Model Years: pusherintakes.com/pusher-powerflow-2015-2019 2020+ Model Years: pusherintakes.com/pusher-powerflow-2020
@THETRUTH-ld2mh 4 ай бұрын
I think you guys can do better on the hose and make it one piece across the radiator and make it where it says pusher on the hose I definitely would buy it then SPE are looking pretty nice The only thing I disagree with their set up is they have a plastic piece with a single O-ring instead of aluminum adapter with a double O-ring Love your pipe and kit, hands-down the best
@riffelsrifles2981 4 ай бұрын
Just installed the pusher intake kit on my 2016 F350 6.7 powerstroke and now my MAF AND THROTTLE is reading 0 yes zero even when driving. Creating DTC CODE P00BD. How can I correct this????? Thank you for your help and time.
@pusherintakes 4 ай бұрын
The first step if you have this issue is to check that the MAF is installed the correct direction and plugged in properly. Please verify this and shoot us an email or call if you need further assistance and we will help you work through it.
@riffelsrifles2981 4 ай бұрын
I installed the pusher intake kit on my 2016 f350 6.7 powerstroke and now mad MAF and throttle sit at zero causing DTC code P00BD. How can I correct this isssue?
@pusherintakes 4 ай бұрын
The first step if you have this issue is to check that the MAF is installed the correct direction and plugged in properly. Please verify this and shoot us an email or call if you need further assistance and we will help you work through it.
@MR11513 4 ай бұрын
Would you pass smog in California???😮
@pusherintakes 4 ай бұрын
You bet, this is fully CARB certified.
@rickcutshaw5123 5 ай бұрын
Any tuning needed after install?
@pusherintakes 4 ай бұрын
This is a race / off-road system for trucks that are already tuned; you won't need to re-tune after this install. If you have a stock truck, you'd need to convert your truck to an off-road vehicle and get a tune in order to run this.
@edflores31 5 ай бұрын
if you delete the heater grid, will the check engine come on?
@chrissantellan6299 5 ай бұрын
This isn't on the website for sale. Only the offroad use only. Where can this be purchased?
@pusherintakes 5 ай бұрын
It is; are you looking at 2011-14 section of the site maybe? This system is for 2015 and up model years only.
@brenden4258 5 ай бұрын
Finally a kit that doesn’t require me to delete my truck
@Hughjohnson222 3 ай бұрын
Should definitely consider deleting it, every epa component on the truck is working to deteriorate the motor at lower miles
@968porsche9 5 ай бұрын
I use alcohol instead of silicone. Had a couple of boots blow off due to the silicone not going away. Alcohol evaporates and lets the rubber mate up to the other syrface pretty well.
@jasonschaeffer72 5 ай бұрын
Wouldn't it be beneficial to Ceramic coat the tubes like Headers to keep the intake air cooler. Just curious 🤔