You did it exactly how I would have. What would you charge to do another?

Damn fine work sir 👍🏾

Very nice, clean work and wiring is very nice. I will have to do this to mine. Thanks

What is the total cost for all hoses and valves?

where do I find the valve?

Can that pin fall out if the engine is still together? Someone had messed with mine and it ramps up real high and I can't seem to get the RPMs to come down no matter which way. I adjust that this is a 13 horse Kohler on a Craftsman Rider which is probably in the 2000s

How do I purchase this kit?

I have never seen that happen before

I notice most people put “power disconnect” switches rather than “battery disconnect” on the ground side, That would cut power from the positive cable entirely.

How do I get a kit

Looks nice.

Can you tell me how you wired it up?

Where did you get the plans for your cnc table?

How much hp on that predator engine? I've got the exact same mower, mint condition, 800hrs with the shitty Kohler 740ch. Was thinking about throwing a 30hp Kawasaki on it if I can't sell it and using it as a backup for my Toro z Master 6000 myride

What a strange table. I love it! Did you build it yourself? I love how you can side-load it super easy with the way it's built. Never seen a table that's meant to be up against a wall like that before. Really innovative.

Nice simple tutorial. 2 things: those are called shackles, not brackets. Also if you use Sheetcam (yes it's extra software to purchase but it's not very expensive), it will do the kerf measurements for you. Its G-Code generator is also the most reliable generator I've ever used.

Did the same thing kzfaq.infooJBvaYtCe_Y?feature=share

👍🏻

Hi! When will you have these back in stock?

Can I buy a post hole auger for the scl850

My JD 25 command, aluminum intake still, had a problem with it. Start getting into thick brush and instead of just giving itself a little too compensate, it floors itself which RPMs shoot up for a sec, then let's off, still under load so it shoots back up 🤦🏻‍♂️. Back and forth the whole time I'm in tall grass but under little load it's fine

I have the urge to do this and if it is slightly underpowered throw a draft through carb turbo setup on it

What was the engine doing when the gov pin fell out? I have the same issue as others mentioned below. I've set the gov numerous times per the service manual. It will start and idle but if I get to half throttle the rpms will take off too high. Decreasing the throttle brings it back down but it will never settle at higher RPM. I'm starting to think something internal but would like to hear more before ripping motor out. Thanks

What an amazing build. Nicely done.

How did you take it out

Can I ask what brand lights did you go with. I like the flush mounted setup. looks good!

Can you please send me the info to buy this kit. Could really use it.

Engineered failure points.

You did a great job the fabrication particular is nuts you did a great job I’m going to try to replicate mine might not be as half as nice as yours great job

Where can these kits be purchased?

A nice upgrade

Does anyone know where to find info on the RATO engine in this thing? Specifically the output shaft diameter.

What spool drive did you use?

I'm looking for hydraulic filter for this unit? Any help ? Number maybe .

Do you guys still sell the kit I couldn’t find it on here

Does anybody have the place where service information can be found on this machine? An owners manual would be nice but I can’t find one anywhere

Hi I just bought one of these at an Auction. It’s jumpy AF. Mine has 2 joysticks, one for the track motors and one for the bucket functions. Is this kit replacing the track joystick?

Good video man. What’s a decent price for these units. I know a guy selling one for $7,000. Thinking about getting it for my landscape company but I want a grapple and an auger so I’m worried that the 2023 model wouldn’t be a good fit with no aux hydraulics. Do you know if the newer ones have aux?

Sorry for bugging you. Do you know what the quick attach on this is called? I can't seem to find any info and it has odd measurements.

Great video, I will be getting the kit. Do you have any idea what the pump is rated for?

​ great video. I have a 2023 with the black arms and hood. The 24’s come with auxiliary hydraulics. I’m hoping they have better drive control also. The 23’s are death machines and I’ve found the issue to be the pilot control valve. It’s not metered properly, forgive me if I’m not using the right words. I am trying to find a PCV (pilot control valve) that will fix this problem. The valve (plungers) don’t open or close at the same rate which makes the unit awful to operate. Sorry for being all over the place with my comment, you should see what it’s like in my head.

Heck ya dude! 🤘👍

where do i find the price for the valve and all the kit

Wow, awesome table!

My buddy just got one of these a 2023 model. Does yours have a blue valve under the front cover that says LRV with a plus and minus. What's that for?

I am in the middle of this conversion. This does not work for every unit. My year looks almost the same but has different plumbing, exhaust, and some other small differences.

This machine really caught my eye, why were they made with no aux hydraulic hookups to run attachments? Bob

I sold mine but loved the build and strength of the unit. It was uncontrollable and had no AUX controls. Will you make a kit for AUX controls? I'd buy another if these kits were available.

Can you do a review video on the machine with operation videos and practicality/ comparison. No videos about them on KZfaq

I just picked one up yesterday. Super squirrelly unit. Going to have to snag this.