I’ve shot winchester white box 115gr - 124gr ball ammo around 600 to 700 rounds out of my ap5p only 1 failure to eject so far

Putting a t5 speed shifter into a t4 transmission. Hope it works?!

Awesome. I'll be doing this on my neighbor's jeep. Thanks for the tip

Dude I wish this was something I knew about before. I was like "where tf are the pin hole?"

rare to see a .22 rimfire "shot out", it is a corrosion problem, early ammo used priming compound that caused metal to corrode very fast, age and neglect does the rest. It would help to use a true heavy duty 1/2 inch drill which runs much slower, is larger in size and has very high torque. A set up where a constant flow of recirculating oil is helpful. A lathe is the best option, the feed rate can be closely regulated.

Nice video man.

This worked great! This fixed my problem! Thank you!😁

This is with an Aksa s4

Wow- thank you! Incredible video- thank you for taking the time to do this. I replaced the relay for $9 and had it in and out within an hour. Saved me a new board or a new dryer- thank you!

Excellent video sir! It looks like the Panzer M4 is comparable (if not identical) to the MAC 1014 I'm looking at.

How has thst barrel liner held up?

922r is not for customers its for the importer

Nice video

You sure can add the extension to the Panzer M4. Seen it done many times.

If that plastic sling attachment is actually part of the mold and not a separate piece from the rest of the stock, it's going to be better than the steel inserted sling attachment point. Putting those steel inserts into plastic and doing it right is not as easy as it seems.

Hey Ginsboy. Now you have built a few with toth tools in what order do you think is the best easiest way to assemble? Build list of directions to make it go smooth. Thanks!

I know this is an 11 year old video, but I am planning to do one of these this week and this was extremely helpful. Thank you!

Thank you sir! This was straight down the middle same as mine. Saved us the cost of a new controller board. Awesome!!!

😂😂😂 Cardboard doesn't ring like steel 😂😂😂

How I break mine in fast and it has worked at least for both shotguns from two different manufactures. One from Panzer and one from MAC. I stripped both down and cleaned and re-oiled everything, racked it 500 times, and kept the spring under tension for a couple days. Ran the MAC 1014 with 2 boxes of low brass for trap shooting the very first time and it's ran flawless. Everything ejected without issues. Though these low brass were around 1200-1300 fps. So I'm not sure if that made a huge difference. I would like to try out some lower fps like the 1150 just to see if they run without ejection issues. Anyways I'm very happy with the guns and for the price you can't beat them.

Back up all your videos today. KZfaq is coming for your content. You need to diversify and put it your library on odysee

I am looking for a 26.5 adaptor to fit a 12 gauge adaptor in

What’s your Facebook

That's interesting that you had to buy the tri-lug flash hider. My AP5 shipped with it.

You didn't settle. That IS an HK. It is only missing the brand stamp. All made on genuine HK certified and supplied equipment by HK trained gun builders. It absolutely will feed hollow points reliably as long as you select the right bullet design/profile/ogive.

There is a difference in hardness and hardenability. 4130 has cr/mo and .3% carbon. Easily takes deep case treatments. Machine then heat/quench temper. 1020/1018 has no alloys with .2% carbon. Not easily hardened except case to .020" at best. Carbon makes the hardness. Alloy addition makes it easy to harden.

Many2 talk...

Butchers!!

Ammunition related failure.

My relay has a burn mark but there is another burn mark from the part next to the relay

As a machinist, hot bluing would likely warp the metal and give you a product with different dimensions than what you started with. Maybe minimal in some applications, but why do it if you can cold blue?

Awesome video.

The difference in qaulity is negligable. Fit and finish might be better but the functionality of the guns is very close. Now if I was military or Swat I would want the Benelli. But for most Americans the Turkish shotguns are more than adequate and depending on them for self defense is not a problem. I have a Tristar G2 that is about 8 years old. I have put about 400 rounds various brands and loads, birdshot, turkey, buckshot and slugs it has never failed to load and go bang yet. I will say my G2 is a slightly different design it has one collar for the gas piston, whereas, these M4 clones have the two gas cylinders.

Clones belong in Star Wars movies ! 😂

Just a thought, couldn’t you pre-drill the FSB and use it as a guide to drill the barrel?

Holy crap are people just realizing that gun manufacturers charge stupid amounts of money for a name….

Come on, you got that vertical foregrip on there and you don't bumpfire it?

Worked perfectly. Thanks!

There is nothing on the panzer m4 that won't enter change with the benelli m4

Can u color case harden an ak receiver. That would be absolutely beautiful. Color case hardend receivers. Nickle plated bolt. A exotic wood furniture. Hot deep blue/ purple blueing for barrel gas block and magazines since case hardening those might not be possible. Or maybe brass or copper accents like those copper colored muzzle devices or titanium brake flash hider to match the purple blue look. All on a forged and chrome lined gun.

tried your method. great results! thanks.

Junk ammo for a junk gun. You get what you pay for. As we say at HK... Stop being poor

Hello. I've been watching your build videos. I'm bout to start tooling up fo ther my first build. Still recommend Toft tools above all others? Also recommend anything they don't have? Thanks for your help!

I have never solder before or fixed anything like this but thanks to you i was able to learn something new and saved $$$. Thank you for make feel like a real man.

What grade of steel wool did you use after browning?

After that light recoil round that failed to eject, I would’ve checked for a barrel obstruction before I fired another round.

Thanks ! Living in Ontario Canada.. MAN We have sooo many restrictions here…..

I like that panzer.. I think it’s worth the money

My bolt would jam to the rear of the receiver when shooting high power loads. The spring would no longer send the bolt home. This happened to my Charles Daily twice and both times I sent it back to the Charles Daily for repairs. Can some tell me what went wrong and how was it repaired? Did the receiver wrap from the high fps rounds? Thanks

Did you headspace this build and drill those holes? Or have I missed a video? Id like to see that work done.