Dirty 77

Пікірлер

@Deucealive75 20 сағат бұрын

If you are watching this and thinking about getting one of these then get the one he has linked here in the comment section. I got three of these from three different sellers. The "FVRITO" is the best of the three. About as close to plug and play as you could get. Just start with a different main jet for your engine and environment. The last one I got was a $20 kit. It had a defective manifold. There was no way to align it properly with the carb because the slotted bolt holes were way off. I had to do some Dremel work to get alignment correct. I still gave it a 2 star review because the carb alone is worth the $20.

@Dirtynuckinfuts Күн бұрын

Having to do this bc we did an oil change and the crank pulley came apart right after

@10minutesounds31 Күн бұрын

I have the exact carb. Is choke up or down

@amirlincoln7183 2 күн бұрын

Perfect video thank you bro 😎

@Greybuiltracing 9 күн бұрын

How about around the step around the valve seat? Have you blended that out?

@NateDog_WDE 10 күн бұрын

As a Ford technician, I'll say that I think they knew exactly what they were doing on these motors when they didn't put any keyways on the timing components and it's not because they are being "cheap". Personally I think they were trying to make the job more difficult (even impossible in some cases) for a diy or independent mechanic to perform these basic jobs keeping the money in the dealerships. Doesn't bother me too much since it's job security for me but I certainly understand why it is frustrating for guys like you and would probably piss me off as well if I was in your shoes.

@jayvlog9841 12 күн бұрын

when i full up and start is run quiek fix how to i have same carburator

@Cereal_Killr 12 күн бұрын

Is that a Pittsburgh accent I hear!?

@davidparks395 14 күн бұрын

I’ve been struggling with getting the bike started after new carburetor install. I’m pretty sure I have my gasket properly installed, so I’m gonna have to play with a larger jet. In NE Ohio so probably about same elevation. Gonna have to play around some now, thanks for the video.

@Deucealive75 12 күн бұрын

Elevation is not a concern here in NE Ohio neighbor. How to start the engine is not often talked about. Right or wrong here's what I do. One pull choked, then turn the choke off. Open the throttle to about 1/8 and pull. The second it starts quickly let go of the throttle. This is the same process I used to kick start my dirt bike. But I didn't have to let go of the throttle because the bike is in neutral. That had a VM36 Mikuni with no idle screw.

@MountainCreek447 22 күн бұрын

Where did you get the plate ?

@newcastlemusicstudios 26 күн бұрын

$30 is a good deal... well maybe

@davidwright2227 Ай бұрын

Just cut the bosses down and mount the coil like Paul states in his packaging. Use the spacers instead of cutting the bracket

@steveneng2787 Ай бұрын

Great video super helpful. You said you're filming with a phone just tap on the screen where you want it to focus. Great video

@taddy656 Ай бұрын

i got this on my stock i mean all stock 196cc and it’s rolling 45 with the 130 jet badass carb for $60

@taddy656 Ай бұрын

it also still has internal governor

@Deucealive75 Ай бұрын

@@taddy656 I did this a couple months ago on a stock 196 and it worked well. Ran the best with a 120 main. You wouldn't want to use a stock 196 muffler. Get a header and muffler for it. I wasn't concerned about the internal governor running less than 5K RPM. I would pull it if I knew I was going to turn more than 6K RPM just to be safe.

@kingosneakers1858 Ай бұрын

My pilot jet is a x36 and it just won’t idle at all unless with the bottom screw 4 full turns out do I need to change my pilot to a x20

@kingosneakers1858 Ай бұрын

So I got the vm22 clone and switch the main jet to 125 and I got it to turn on it every time I turn the throttle it just dies on me or is boggy

@freshbutplain1144 Ай бұрын

Are the crankshafts interchangeable?

@Greybuiltracing Ай бұрын

Hey, how about the VM 22 knock offs that say Miki on it? Are those do those worth the same as this one. Also one more important question where do I get the Jets for it as far as the pilot goes I have jets for it, but I cannot find pilot jets for this carburetor. I looked all over Amazon everywhere and I can’t find it.

@dirty7739 Ай бұрын

Those ones are hard to find jets for. The knock offs are easier and I think they're better.

@Deucealive75 Ай бұрын

Funny thing about these governor videos. The good ones don't get very many views, but the ones done by guys who don't know what they are doing get 10's of thousands of views.

@blackwallace2267 Ай бұрын

How many turns air mixture screw and fuel and pilot I want to try ur tune

@mu9627 Ай бұрын

Just a quick thanks and great job taking time to explain for those of us that do our own or help others out, as is my case. I was surprised Acura made it a bit easier than most as I've had the dash out on some. Real pain. Thanks again man!

@DeezGarage Ай бұрын

You can “make” that exact carb a meth carb with some drill bits 😏

@mateomolar8618 Ай бұрын

Mine didn’t came with jets

@jeffreyodachowski6247 Ай бұрын

So its been a year i was wondering if you tried to use that valve seat cutter again? And if so how did it go? I was going to buy one and try to make a 31mm in to a 32mm. That kit is $64 on Amazon now and its the only one thats not over 300$ for a 32mm.

@m1000black Ай бұрын

Excellent explanation of the air leaks!!!! Had a few guys tell me these exact carbs where cheap shit.... Yet my son's small Baja 196 rips with it. Your explanation of the jet sizing is gonna be a life saver!!! Cause I've been getting bogging at about half throttle. I'll swap the standard jet for a larger one. I'll report back once done

@kingspiritz839 7 күн бұрын

How did it go I have a 196 but wanna find out what jet it needs

@m1000black 6 күн бұрын

@@kingspiritz839 it went excellent. My carb kit only had up to a 125 jet. I think the 130 would have been perfect. But it gets my 12 year old son going 30+ mph

@Lookatthebottom Ай бұрын

I'm about to do a first carb change. I'm going with the cheap Amazon one to replace the stock one on my Chinese bike. It's interesting to see all the details of possible problems when setting up.