Companion as the edgetx of the jumper t20s 2.4Ghz is updated

For that price there should be no problems to fix with glue or by yourself, what a shame dji

What is the size of the wire, is it 16 awg or 22….. also what size heatshrink do you use to protect the receiver?

Thanks

Is there a way to hack the DJI Googles HD Low latency (RH) v1 to be used either in a DJI Spark or DJI Mavic mini? Thanks for the help

Can i slap a dji 03 on this drone?

perfect just what i needed

I popped a set of SuperNovas on my 5 inch Alien 6S build. One motor arced through the frame and the other three got extremely hot within 5s of testing it. I never got a chance to pop on props and take it for a flight. I'll be going back to my previous motors after that experience.

Testing 20$ish frame.. lost camera.😅

Excellent video very clear and informative thank you 🎉

I have one. Since it is the only 3,5 i have, I can't say of it is the best, but i can, confirm all the positives! Very agile, lightweight, efficient quad. And cheap on top of all. Couldn't recommend it more! 👌

The flying here is so light if you said there was a difference I'd doubt you actually noticed.

Jumper is one of the worst brands in fpv. They put too small cables on gimbal and they break mid air dont trust it.

It can be used in the plane by installing a pwm radiomaster receiver

It can be used in the ship by installing a pwm receiver

Hi Darren, I’m reading up CASA for fpv. It seems painful. Is the ‘send its’ approach also applicable here?

Disclaimer, while I can fly the wings / props off of anything RC, all of the software, updating and flashing required with these drones gives me headaches as I am not good with programming and even tho there are hundreds of instructional videos, there are too many variables even for step by step instructions to cover everyone's situations. So my radio was stuck loading the Lua script. After searching possible solutions, turning up the baude rate finally allowed it to load. Now I have two questions before I proceed with my Express Lrs module setup. 1 - I cant even recall what the baude rate was set to prior to increasing it to load the Lua script. Although I havnt yet learned what the baude rate is, since I turned it up to the maximum to load the script, I assume I should lower it, and did, to 400, but I would appreciate a bit of guidance here before I proceed. 2 - In one of the elrs setup videos I watched while waiting on delivery of my module, another YT'er advised updating the Boxers Luascript, which may be what took place in your instructions, Im not sure, but if not, since I cant loacte the original source, how does one go about updating a Lua-script? Thanks for any help anyone cares to offer, cheers.

So does this mean I can’t fly my self build drone if it doesn’t have gps??

HDZERO cant acheive crystal clear HD though thats its tradeoff.

darren problem is in live video and/or rec vide0?.thx for video bro.

If so, the problem IS BAD QUALITY CONTROL BY DJI...which is worrying...

si es asi el problema ,ES UN MAL CONTROL DE CALIDAD DE DJI...lo cual es preocupante...

Thanks for creating and sharing this video. Learned a lot. You get an S from me.

Very intersting indeed. One aspect that you didn't cover, was the fact the Dji have restrictions depending on where you live, related to where you can fly, and how high. For many, this must be a deal breaker. Great video. Thanks.

can I use 850 or 1050mah battery on 3.5" fpv?

Most racers are using HDZero these days.

Is the rdc90 gimbal that i have on my broken T20 compatible with this radio?

I still fly 4s.

Bro you sound salty af are you jealous that someone is making money of a product.

I'm just surprised that DJI hasn't fixed this between batches during manufacturing, even if it was to just add the adhesive like you did during assembly!

Just looking at those calipers I think the sticker is off... 😂 So much more error in your measurement than is acceptable to start fussing about somthing being closer to 1 mm larger than 1 mm smaller... What a joke....

Thank you. Helpful 🙂

Is the boxer a good radio for rc planes? I'm actually looking into getting a new radio and the new jumper t14 v2 caught my eye I want a radio for both fpv and planes I'm flying with elrs on my quads and spektrum on my planes so I'm either wanting a 4in1 radio with a elrs module is the cheapest route however I don't think that jumper offers a internal 4in1 but rather has the external 4in1 module

Well have have these's goggles with O3 air units and have flown in area's not allowed a bunch of times ,nothing happens ever only if you fly a Dji drone that has a id chip in it is the only way it makes a difference so if you fly your built fpv drone your fine just don't advertise were you fly and don't cause problems that you will get you called on that's the only way you will get caught there is no dark secret with theses' goggles the gps only works with a remote id installed on your drone, so dont put one on and stay away from area's you can get caught just be safe its easy

Hi I love the video but I was wondering what is the difference between the TCMMRC Overfrequency 2.0 TCMMRC UR26 Mermaid 220 if you know can you help

So all the elrs hardware will work with each other ? eg. Happymodel TX with iflight Rx

Daren you are a saviour!

what drone is that? at the end of the video with yellow canopy

OpenTX IS NOT a variation of EdgeTX. EdgeTX is a FORK of the OpenTX project, born in 2021. Just to be precise.

Nothing wrong with remote ID, if you have a problem with this, fight the regulation not the manufacturer trying to comply. You have the freedom to choose, don't buy their product.

Could you share model.yml file for T14?)

awesome! Thanks! Great to see your videos!

Awesome video Darren!!!!!

Hi I have a problem removing tin in my FC (ESC PIn ). The tin is very hard to melt even though the solder iron so hot. Do you know how can I check my board is okay or not? I worry I damage the board because of touching the soldering iron too long until get so hot

perfect video exactly what I needed. Surely would have ended up with the (more expensive) 4 in 1 instead of ELRS without your help

I bought the cc2500 by mistake is there a way to put elrs on the radio other than buying a module which I have ordered and am waiting on any help is appreciated

I don’t recall having to go through the entire ExpresssLRS process with my pocket. Isn’t it already set up with 3.0 or more version of ELRS?

What cable to buy for simulator usb to usb c or usb to 3.5mm

I really need your help

I prefer a momentary switch way over a toggle one. By software you can make a toggle one out of a momentary one, with ONE line in the special functions. But you cannot create a momentary one out of a toggle switch. I disarm my wings with a 2sec-press on a momentary switch, to absolutely avoid accidential mid flight disarm. A toggle switch is just useless for that.