Sometimes the size of coupling are not the same,using straight edge are not applicable

How do I tell if it's a heat treated shaft?

You only want to drive o n the inner race..

why did you skip pulling off bearing?

OH GOD FUCK IMPERIAL

epic

I hesitated to use my wheel puller but at this hour I wasn’t going to wait for hf to open to buy a bearing puller like you use, but my bearings are shot anyways thanks for this video very informative and well done

Ayuda a mi clutch se rompieron las láminas que sujetan los pines se rompieron tres y son 8 ocupo saber cómo se llaman y dónde las consigo

How did you know to go from metric (20mm) to imperial (3/4") on the first 2 bolts?

A slow-running machine and a fast machine - how many revolutions per minute?

Where can I purchase those dials ?

Thanks. About your tip on the direction of the link clip. Is there a two way clip for bidirectional motors such as stepper motor positioning systems, or is it less important with low power/speed situations?

Sometimes you get materials like 17-4ph and it gets trickier but this is an amazing video thanks!

how do you remove a bearing if it’s not on the shaft but in a housing cover?

Very nice presentation and explanation! Do you do side work? I have a 9-1/2” long drill press spindle that is out about .040”? Thank you

Como sedeslaquea un kloch de un torrneyto 15 20006

14:12 what is a stolen?

I think it was easier take the rotor out of the armature and then install the bearings carefully. Second the bearing you installed with your hands is a big issue for sure. It needs to grip or it will make a mess if not happened already.

Shbtsdn bhd &gajetsdn bhd & tuah resueo sdn bhd

Thank you very much for making this video. It's very easy for me to follow and understand! Wish you well!

4:54 where the nut gets measured

Hello Sir, I am following you from Algeria. Greetings to you. I have a question. I have a motor with a power of 15kw and 3000t/m. I want to reduce the rotation to 1500t/m. What are the diameters of the pulley for the motor and the other for the opposite one

You sounds like Ed Bolian from vinwiki

Hi sir ,thanks for this video. I have few queries, 1) what is the ideal piston rod runout reading at head end while installing the new compressor? 2) we have got the rod to rod pressure packing case bottom gap very less than the top,concern is if the piston wear band get wear then rod will touch to packing case and cause damage to rod. What corrections to be made for this? Piston rod runout reading are at the positive at head end when we start to move from Crank end with zero dial indicator.

I have all these bolts and I'm like how the heck do I measure him and I've looked and looked and all these people give all these explanations and I'm like I don't know what the heck they're talking about and you have the most comprehensive one thank you sir

Thanks for the video =). Very systematic and efficient methodology, and very high quality content. Out of interest, how many hours did it take you to make the video?

What's the product name of the 'driveup set'??

I'd love to know what model that bearing heater is! Does anyone have an idea?

My electric motor needs bearings replacement and the maintenance store issued one ball bearing and one cylindrical roller bearing. Which end of the motor would I fit each of these bearings . And why ? Can I get some help please

Thank you for creating this video

Nicely explained thank you

Can we use this method to make its model in Solidworks

Yes

Bro....I don't even know you and you're a better dad than my dad, lol🤝🏻👍

Insanely over- complicated. Thanks for explaining.

Kaha milega

The one part I wanted to see.... "Ok, got the bearing off", OFF CAMERA!?! Ugh

It would be great if you could show how to use dial indicators to align the shafts

TOTALLY BRILLIANT! Thank You Mate! Solved our problem!

What if the manual says 10mm of sag?

Why was the paint that you removed on the shaft? Identification for manufacturing purposes? I agree with removing the armature to replace bearings. I always feel better pressing them on when resistance exists.You did a nice job on this video. It is so clear and shows detail very well.

didn't know about thread pitch gauges or tap drill charts... so thanks!

How do you did bolt length from measuring the diameter of the bolt length of body with caliper??

OMG this guy’s voice puts me to sleep. He sounds and talks like the dry eyes guy in those commercials.

Why do they come glued to the shaft??? I am trying to repair the clutch contacts of a motor and the bearing is preventing me to remove the part that needs to be scrapped with sand paper

what is the purpose of the washer

very helpful thankyou

Very nice video congratulations 🎊 I have a question, there's a direct relationship between the size of hexagon head an the size of bolts body, can you give me a light on that please, I will appreciate that. Bless.

Is there any force applied while u heating the shaft