Thank you!!!!! Was ready to throw it away, but thought I'd KZfaq it first. You just saved me some $$$. Thanks again! :)
@mrsdoylespinniedoyle19567 күн бұрын
Thank you. That was a huge help when it came to dismantling so that I could clean up the commutator and brushes.
@theresamiller295012 күн бұрын
So, I was all excited to fix my Nutribullet, took it apart, and cleaned up all the gunk. Got it all put back together and now it has no power at all. Any ideas of what I could have done wrong? It had power before, it just didn't spin...now, nothing.
@peter-pg5yc13 күн бұрын
I used silicone grease to lube springs and plastic parts. wont effect or hurt palstic. Plumbing silicone is fine they sell small tubes of it.
@MultiPetercool23 күн бұрын
I drilled a hole in the Center of the top panel of my Masterbuilt and hung a hook on the inside with a couple of nuts and a washer. I then bought two meat hangers and hung a 15 pound brisket and it smoked beautifully.
@Pr0j3ctFailur323 күн бұрын
I barely have the gas turn on on both the smoker and propane tank and its still climbing to 300 degrees /:
@UntrepidOne24 күн бұрын
Not a complete disassemble.
@woodystefeneylee729027 күн бұрын
I saw this yesterday at Home Depot on sale now $279
@MultiPetercool23 күн бұрын
Got one two years ago on Wayfair off-season for $180! Replace the smoke pan with a cheap cast iron pan.
@woodystefeneylee729023 күн бұрын
@@MultiPetercool thank you .... I like the cast iron pan idea.
@MultiPetercool23 күн бұрын
@@woodystefeneylee7290 I can’t take credit for it. I saw it on another channel. Makes a big difference in terms of temperature stability and consistent smoke production.
@millardscott564628 күн бұрын
Great video, concise and very well thought out.
@refugeinc.15929 күн бұрын
This made absolutely no sense at all.
@billmellater29 күн бұрын
Now let's talk about the little plastic activator tabs on the cups that if broken won't activate the machine.
@billmellater29 күн бұрын
Sometimes lithium grease can degrade plastic over time.
@KevinMiller-lh9urАй бұрын
If you put the new bearings in the freezer for an hour and get them real cold, they shrink enough to make them go back in a lot easier.
@TractorJebАй бұрын
Thanks for the info
@rodneymahler472Ай бұрын
Great job sir. Just had my canvas blow apart. Tired of replacing every time we have a bad storm. Just wanted to let you know that I will be using your video to do the same. Thank you for doing the video and posting it. You earned a subscriber 👍
@thehandyoutdoorsman9014Ай бұрын
Thank you!
@KuzweKanfarmsАй бұрын
awesome video... boy I wish I had seen this 2 years ago, I wouldn't have had to live with extension cords all over the place!! Great Job
@thehandyoutdoorsman90145 күн бұрын
Just now seeing your response - extension cords suck - been there and done that - main reason for the electrical panel. Thanks for watching!
@jameskelly9800Ай бұрын
Good video. The backup pump is a great idea. In areas where freezing weather is an issue, care should be taken that standing water in the pipes does not occur.
@jimjurgens1895Ай бұрын
Great video, I let mine sit for 1.5 years and need to pull the carb, we have bad gas in Alaska..
@thehandyoutdoorsman9014Ай бұрын
Happy to hear it was helpful. Thanks for watching.
@randyjerrett3385Ай бұрын
Very nice!!! Thanks for the video
@thehandyoutdoorsman9014Ай бұрын
Happy to hear it was helpful. Thanks for watching.
@mohalomari2479Ай бұрын
المحرك يعمل ولاكن يخرج شرار من المحرك
@ibbermanАй бұрын
Great I'll do this to my oldie, what gauge wire and what size fuse did you use?? Thanks for the video👍👍👍
@thehandyoutdoorsman9014Ай бұрын
The wire was 14 gauged. Don't recall what the fuse size was. Thanks for watching!
@tylerwestman5258Ай бұрын
That smoker can use charcoal if you bought it new. it’s called master built dual fuel smoker. I have the same one and rarely use propane… and sometimes nothing but smoke for cheese
@rjwrestling1Ай бұрын
Worked thanks!!
@thehandyoutdoorsman9014Ай бұрын
Happy to hear it was helpful. Thanks for watching.
@kyleschaff1319Ай бұрын
Curious how it’s held up of the last three years.
@joed9988Ай бұрын
Great job but wouldnt have been easier to just build the hole thing with wood? Intead of having to build. Around the frame
@thehandyoutdoorsman9014Ай бұрын
As I have told others, nothing was wrong with the frame - why throw it away. Saved some money and time in not staring from scratch.
@joedaggett4445Ай бұрын
@@thehandyoutdoorsman9014 hey like i said great job bro i only found the video because i was thinking of doing the same my frames still good too but after watch the video i don't really see a benefit of keeping the metal frame it doesn't seem to add anything accept the hassle of building around it. it gives a you a starting off point i guess and mabey we a different method that doesn't involve sliding it through holes in the wood or notching . your frame is now like 75% new wood.
@xander7738Ай бұрын
Plis spark #? Numero gracias
@deborahwiggins1651Ай бұрын
Thank you. This was helpful
@thehandyoutdoorsman9014Ай бұрын
Your welcome - thanks for watching!
@inscrutianaIIАй бұрын
For the C3101, they are now listing this as N008792. Model lookup "suggested items" page build is helpful at Replacement Parts.
@1pittisАй бұрын
Worked a treat and saved me some £££. Only took about 15mins to do. Try this before buying a new one. Thank you very much! 👍 😁
@karlkelly88742 ай бұрын
I really like your videos
@thehandyoutdoorsman90142 ай бұрын
Glad to hear that, thanks for watching!
@mwt19752 ай бұрын
Don't drive the inner bearing in too far. Mine seized up on the bearing spacer and I could not hammer out the new bearing with the spacer wedged in the way it was. I am used to bearings stopping when they reach a retaining lip but this inner bearing just keeps going in. My guess is you leave the spacer a little loose in there and then it will fully tighten up AFTER you reinstall the drum and tighten the bolt holding the spindle on. Also, that collar that goes over the drum shaft has a rubber gasket on the underside. Mine was torn up when I removed it and I had to order it. Keep this in mind if you are wanting to do the job in one day, you will want to make sure you have that as well as your bearing and seal kit.
@Trashguy742 ай бұрын
Would you happen to know what the part number is
@karjack112 ай бұрын
I've sat here at work trying to figure out my course of action to replace the canvas cover on my harbor freight cover pro shelter that is 2 years old and starting to crack. This is the solution! I was going to throw a 12mm thick tarp on top but I like this once and done idea!!
@user-bc7rv7ut8f2 ай бұрын
I have some old new stock plow points and other items for Ferguson plows if any body is interested
@obxarms76853 ай бұрын
Awesome job! Where did you get the bolt plate adapters for the ends of those vertical poles to secure them to the concrete?
@blmdh20s3 ай бұрын
I like your idea of the angle iron between the 2 light brackets. I'm considering adding an implement LED light circuit to the harness coming from the light switch in the dash so whenever I have the front lights on, I have the ability to activate the implement light via a second switch. I chose the dash light switch as the power source so that I don't accidentally leave the light on killing the battery. I'm also considering placing a small toolbox onto that angle iron to keep me losing my implement pins (which I'm doing constantly). I'm placing the flasher and it's switch under the dash as well. This is a good idea.
@gkalligher19583 ай бұрын
Extremely helpful!
@thehandyoutdoorsman90143 ай бұрын
Glad to hear it. Thanks for watching and commenting!
@Zgriffinable3 ай бұрын
very helpful but my problem was different. During operation the 1/4"? threaded plastic cylinder that held one of the two switches twisted off rather than glue it back, I bought a longer screw (1/2") and drilled into the mounting plate to which the threaded plastic cylinder had been attached. I tightened it so much that is bowed the plastic member (two screws held it and in the center was the cylindrical extension of the white teflon? switch activator ie when you push down on the mixer vessel it pushes on the white teflon member and moves the switch to start the mixer motor), anyway, unit now operational so no need to discard. kzfaq.info/get/bejne/ppOjlJBnvtvXe2g.html
@ryurc30333 ай бұрын
What about getting the spindle itself to drop down so I can fix the bearings
@thehandyoutdoorsman90143 ай бұрын
Once the taper bushing comes off you should be able to unbolt the pully assembly to to get to the bushing.
3 ай бұрын
Thanks so much! I guess this is another problem because it still doesn't work, but the video helped me a lot. thank you so much.
@thehandyoutdoorsman90143 ай бұрын
Raul - your welcome - good luck in your troubleshooting.
@user-il7eg9qq9c3 ай бұрын
Thanks for the really helpful video, step by step. This is a really tough job but my husband did it and now our machine is quiet. It would be helpful to have the steps go through all the putting it back together process. Some of the reassembling is tricky too. Our bearings came out with great difficulty. Penetrating oil was helpful.
@DixieC-vj2sg3 ай бұрын
Thank you for posting this! Our Nutribullet stopped working and was ready to buy a new one - didn't even occur to me to look at those levers. FYI - Didn't even have to pour the water to solve the problem - I started by taking a small knife with a sharp edge and carefully cleaned out dried food/buildup from each of the edges of each lever. Took about 10 minutes max. WORKS PERFECTLY now! In my case it was an easy hack but wouldn't have thought of it without your video.
@samisolissolis65563 ай бұрын
What type of gas is used in this type of generator?
@brockeverist46543 ай бұрын
What type of service panel is that
@thehandyoutdoorsman90145 күн бұрын
Apologize for delayed response. All parts are listed at the end of the video. Just a 100amp panel.
@paulj.91964 ай бұрын
I bought a brand new John Deere X370 this season with the 44" snowblower attachment. I have a total of 15 hours on it, and the snowblower's drive belt sheared off (John Deere Part No. M174506; 78" in length). Had I known ahead of time what a poor design this is to change a simple belt, I would have literally considered purchasing a different brand.
@bborgan76114 ай бұрын
Thank you!
@sheilajohn67974 ай бұрын
Thanks so much, I followed your instructions and my Nutribullet now works! I knew I shouldn't have listened to my husband who told me to throw it out! Also, hot water with a dropper? What a ridiculous suggestion from Nutribullet!
@thehandyoutdoorsman90144 ай бұрын
Glad the video was helpful. Congratulations on a working working Nutribullet!
@ralfkramden92914 ай бұрын
Appreciate the video as I am about to do my bearings. One thing I disagree with you on is the fact you split the internal seal. IMO, you insert the seal as one unit, lube the land where the seal rides on the shaft and install the inner drum that way. In case your seal sits slightly different from the original, you could get a leak past that seal. One tip, you could have put the bolt back into the shaft to save the end from mushrooming when you pounded it out