2021 3D Printer review - Ender 5 Pro Part 2: $13 Auto bed leveling sensor, compiling Marlin 2.0.7.2

Рет қаралды 40,525

3 жыл бұрын

In this video, I will try to spend less than $20 to add a $12.99 super cheap auto bed leveling sensor, a $5.5 filament sensor, other free printable upgrades, and compile the latest Marlin 2.0.7.2 firmware for the Ender- Pro and try to make this printer work even better.
(Affiliate Links)
Creality Refurbished Printers (SAVE UP TO 50%):
bit.ly/3q17mGi
Used Ender-3 ($79):
Maybe in bad condition, but if you know how to fix some common issues of a 3D printer and have spare parts to replace by yourself, that could be an amazing deal:
bit.ly/3LPnzHw
Creality Ender-5 Pro:
www.comgrow.com/collections/c...
Filament Sensor:
amzn.to/3BFsINC ($10.89 Pack of 2)
3D touch sensor:
ebay.us/vfkSK5 ($12.99)
Printable upgrades from Thingiverse:
Ender 5 Bed Strain Relief by grizzlyeric
www.thingiverse.com/thing:366...
Ender 5 BLTouch Mount remix by Aurora (Added 2.5mm to work Ender-5 Pro)
www.thingiverse.com/thing:481...
Filament sensor mount by Aurora (For the one that cost $5.5 in my video)
www.thingiverse.com/thing:481...
Ender 5 bed supports by jumpshoutmedia
www.thingiverse.com/thing:347...
Ender 5 Cable Cover by dbltrbl023
www.thingiverse.com/thing:414...
I hope you like the upgrades I put on this Ender-5 Pro.
Normally me and my brother Helios will make a new video on the weekend, so check out my channel every Monday and you will see something new.
Thank you so much for watching and I will see you next week.
Disclaimer:
The purpose of making this video is to share what I did to update the firmware to make it works on my printer. Since the manufacturer may change the hardware configuration from time to time, the firmware that works on my printer may NOT work on yours. I am not able to provide support to identify your problem. Thank you!
Follow us on Twitter:
/ aurora_lung

Пікірлер: 136

@janpetersen8441 3 жыл бұрын

Another great video, tank you. The way you tackle such a complicated topic as compiling Marlin is fantastic. I have seen other videos on the topic, but would end up being confused after seeing them. But your video is easy to follow, and you explain what each change does. Fantastic work.

@AuroraTech 3 жыл бұрын

Thanks so much, I'm glad that you find this video informative!

@amamkomurrell2371 Жыл бұрын

Facts bro I just started all this printing stuff and that's how I felt after watching. So many dudes got me worse off then when I started (no offense Aurora) the darn child helped with absolutely everything. Aurora yo lookout Thank you big time G!!!

@nicksterspad 2 жыл бұрын

You explain things better than some people that have been doing this their whole life! It's crazy how talented you are at such a young age. I'm sure you have a bright future ahead of you!

@keithwins 2 жыл бұрын

Every one of your vids that I've seen are fantastic: so clear, methodical, well-paced. Excellent work.

@itzmeagain8011 2 жыл бұрын

Great video, thanks. I am completely new to 3d printing, having just bought and Ender 5 Pro. I have been looking for a reasonable auto bed leveler for a month or so. I am now convinced to go your route and also add filament detection. Although I am comfortable with code and config files I would have struggled with the requirements for this. Your detailed and straightforward presentation of all the required process was amazing and I am now confident to go ahead and buy the hardware along with making the firmware changes, as long as I book mark your video. Many thanks.

@barrymaley 3 жыл бұрын

Awesome! Very clear presentation, easy understandable. BTW, I printed your filament sensor mounting bracket. But added a brim in Cura, so it perfectly sat on glass plate. Thank you so much!

@AuroraTech 3 жыл бұрын

Thank you for watching! I'm super glad these videos could be of use to you. :D

@DevlinLove54-si3fp 5 ай бұрын

THANK YOU ! I spend 1h + trying to make it work as they show in the official videos and the dmn display wont start I was about to return it cuz of defective item but I'll try the way you showed in the video 1st before wasting another month replacing it :) I'm following your videos for few years now and I've always been super happy with the explanations you give so all I can say is Keep up the amazing work !

@dragonswordstriker 2 жыл бұрын

Your videos are very helpful and surprisingly in depth! Thanks for the guide!

@aps3000miki 3 жыл бұрын

If someone says your videos are good, he is not telling the truth. Your videos are actually fantastic. To the point, well thought through, accurate, and very well explained. You make compiling Marlin "idiot-proof". And even a bit entertaining because of the confidence you show. I would like to see some "before and after" prints and I want your thoughts on improving this printer even further. I know it is possible but I like the way you think and do. Thank you very much.

@NoTimeForThatNow 2 жыл бұрын

If your BLTouch is not working right and just sits there failing to home the Z axis, it may be because you have the new connector wiring harness. The instructions on Marlin in this video should only be used for BLTouch wiring done exactly as shown in the video. The new BLTouch connector connects to a different connector on the motherboard and that makes a huge difference. The line about the “Z min probe uses z min endstop pin” that is enabled here should not be enabled, instead the “use probe for z homing” should be enabled. See the video on the Ender 3 Pro Marlin extra features + filament sensor + 3D / BLTouch on this same channel. It is about one month after this video.

@congpham8864 2 жыл бұрын

You are one of the best 3D printer explainer with great info and great explanation! I have subscribed and hope you continue to grow your channel!

@ZeroEntropy. 3 жыл бұрын

You are so awesome, love these videos!! Just right to what needs to be done and the facts!

@TOWEOatmeal 3 жыл бұрын

Okay, I don't think I've seen a better guide on this yet. I think you just solved all of my problems. Keep it up!

@AuroraTech 3 жыл бұрын

Thank you so much, I'm really glad this could help you out!

@TOWEOatmeal 3 жыл бұрын

@@AuroraTech No problem! Thanks to you, I printed something for the first time last night 😁

@sebastianrose9811 3 жыл бұрын

Sos una campeona !!! Gracias por compartir tus experiencias, éxitos y saludos desde Argentina 💪💪💪

@alienatheart 3 жыл бұрын

Thanks, pls do a comparison again after the upgrades

@natebean151 3 жыл бұрын

Thanks for info i learned alot solved other problems i had. Your video was Very detailed better then other videos.

@petrusvanbreda6533 2 жыл бұрын

Hi. I like your videos. They are easy and straight forward to follow. Keep up the good work.

@mx83toy 2 жыл бұрын

Love your videos, great work :) I've just ordered the tronxy d01 was tossing up between it and the saphire pro :)

@newsbet24 3 жыл бұрын

Congratulations on your tutorials. They are really very well done. I follow you from Italy. Thanks

@AuroraTech 3 жыл бұрын

Thank you so much for your support! Happy to help :)

@pipoviola 2 жыл бұрын

You are simply GENIUS! Thank you for teaching us so much.

@joop2295 3 жыл бұрын

Very clear information and a very explanatory video!

@defaulted1237 3 жыл бұрын

Great video! Thanks for your help!

@FritsBoelema 2 жыл бұрын

Thank You very much, this helps me a lot.

@noelwiltshire8926 2 жыл бұрын

That's the best explantion of Marlin that I have ever seen.

@noelwiltshire8926 2 жыл бұрын

I forgot to say I'm 70 years old.

@mirage3rd 2 жыл бұрын

Wow. Impressive explanations. Thanks

@patriciosanmartin5242 2 жыл бұрын

(I apologize in advance for my English) Excellent video! this worked for me, BUT! I have an Ender 5 (Regular, not Pro), but with a few upgrades, like the silent board with 4.2.7 fw, a capricorn tube, alluminum extruder, 3D Touch, among other things. I followed every single step in this video, but when I tried to print an object, the z-axis had a problem. The 3DTouch worked compensating the leveling of the bed while printing, but for some reason the z- axis did not step down while switching from one layer to another, this problem became a bad headache for me. So while repeating your video over and over again, I noticed that since I made some upgrades to my printer, I could say that i do not have the regular version anymore, but rather the Pro version. So I switched from the Ender 5 fw to the Ender 5 Pro fw, followed your steps one more time, upgrade the fw on my printer, made a printing test and it worked like a charm! the results were more than great, almost perfect :D. I'm sharing my experience with this video in case that there is someone that's having the same issue that i had, don´t give up and always relay on the community ;) Fantastic work Aurora Tech, thanks a lot for your outstanding tutorials. Greetings from Chile.

@AuroraTech 2 жыл бұрын

Great! I am glad to hear that! Yes, you are right, Ender-5 and Ender-5 Pro are using different lead screw, that may result in Z movement issues if the step/mm is not adjusted correctly.

@jakenorth4811 3 жыл бұрын

this is so well done. thank you.

@MicrobyteAlan 2 жыл бұрын

Very comprehensive, thanks

@GasBrakeSim 2 жыл бұрын

Thank you so much for your videos !

@NautiRulz 2 жыл бұрын

Awesome! Keep it up 👍

@seanpeterson862 2 жыл бұрын

Thank you!

@mrr3000gt 2 жыл бұрын

Awesome: Great job on this!

@declanswords8704 2 жыл бұрын

fantastic video, well done

@benb1355 2 жыл бұрын

I can see you have a CR-10S Pro V2 3D Printer and would love to see your review of it and a comparison between that and the Ender 5 Pro.

@kelvinleung8763 3 жыл бұрын

Great! Thanks for sharing! 😊

@geoffreysiembor119 3 жыл бұрын

Another Awesome video!

@Corky907 2 жыл бұрын

this is a great step by step except once I got everything edited, I had no project tasks tab and I could not build it

@Logix727 2 жыл бұрын

stuck there 2 how did u fix?

@omgextrd 2 жыл бұрын

Great video!

@superchargerone 2 жыл бұрын

Love your videos. Great content and very clear and concise presentation! I am on the market for a 3D printer and was offered a used Ender 5 Pro. Your videos allows me to learn about the 5 Pro in detail before I purchase it. Thank you. Subscribed.

@SPD3DPrinting Жыл бұрын

Hello! I just bought refurbished 5 Pro from comgrow and want to do these upgrades. Would you make any changes to your suggested list of upgrades? Would these instructions still work or are they outdated? Thank you for your help!

@gljay Жыл бұрын

I wonder what calculations were programmed into that spreadsheet?

@hebert4230 2 жыл бұрын

I have followed this to a tee. But I cannot see project tasks in my vs code. Great video though, very helpful

@user-qu7yk5lw2v 3 жыл бұрын

A you the Best.! Thanks

@charlesalvarenga979 10 ай бұрын

Hi Aurora. Thank tou for a great vídeo. I haver a question. I am a New in VS code. I Did all modifications that you said to do, no problem. But at file compilation in tasks, do not appear for me, the list of board. Could you help me please ?

@EttozenProject 3 жыл бұрын

i'm speechless xD, wut a nice video! thanks!

@EttozenProject 3 жыл бұрын

But, now i'm trying to update firmware to 2.0.9, and got error eeprom version, how to fix? Thank you!

@ThiagoLaranjeiraZerooneBit 2 жыл бұрын

very informative thx kid =]

@creepinonthebabes 2 жыл бұрын

ALL new printers should have auto bed leveling and filament sensor as standard. they should have upgrade models that have silent motherboards and silent Noctua fans installed

@pen25 3 жыл бұрын

great video. thank yo for sharing. just subbed as i didnt know. sharing on twitter now

@AuroraTech 3 жыл бұрын

Thank you so much for all your support, we appreciate everything!

@touchofeverything9677 2 жыл бұрын

What is the best fulfillment the plastic you used to make them what is the best one for under five pro

@charlesrestivo870 2 жыл бұрын

Way way beyond my skills Great video never less

@janconstandse3053 2 жыл бұрын

Thank you for a great video. I watched it over and over while compiling. I'm building the exact same setup ( BLtouch and filament sensor, same motherboard). I ran into an issue while compiling. Error: BLTOUCH_SET_5V_MODE is not compatible with the Z_MIN_PIN. I tried the 2.0.7.2, but also the newest version of Marlin with its configurations but i could not fix this compiling error. Is there a fix?

@michaelbowman4919 Жыл бұрын

Hi did you change the start gcode with the 3d touch.?

@MarkWascherJr Жыл бұрын

I've followed your steps but I'm having issues with the printer locking up when the filament is in the runout sensor. Pulling the filament out of the sensor causes the printer to reboot.

@jyotirmoyjd 2 жыл бұрын

Hello, is it possible for you to share the compiled firmware ? I'm using an Ender 5 pro. With marlin 2.0.x (compiled as you've shown here) the probe stopped probing altogether.

@davidwilson8550 2 жыл бұрын

I'm just wondering something ... Why did you connect to the z limit port? On that kind of board, you can use the 5 pin connector. I did it like that and works flawlessly. Z endsensor has to be disconnected too but there is no real reason to use that port.

@mikomichelle 2 жыл бұрын

necesito ayuda no puedo, me marca error al querer modificar el archivo solo para sensor de filamento

@XxYobrohoxX 2 жыл бұрын

Hello, so i've been trying to get my ender 5 pro to have bltouch with filament sensor without the adaptive board.. and cant find anything about it besides building the firmware.. i tried to compile and build this and it was an epic fail.. can you point me in the right direction as far as installing the bltouch and filament sensor on the ender 5 pro.. thanks

@hellbz 2 жыл бұрын

Can you put a BTT RRF Board in a Ender 5 ?

@jayswint1192 3 жыл бұрын

awesome video! I am unable to get the connectors for the 3d touch to stay in. they fall out very easily without much force, should I hot glue them? I don’t know what else to do

@AuroraTech 3 жыл бұрын

Yes, you may glue it or change to a JST connector. Please watch what I did to the Ender-3 Pro bltouch connector: kzfaq.info/get/bejne/jqunhrR5t8-xfKM.html

@trissienl5308 Жыл бұрын

its not giving me the option for bltouch

@jf6720 2 жыл бұрын

Thanks for a very helpful video! I would love to invest in your future, I am embarrassed to think of what I was doing at your age :)

@romanfn 2 жыл бұрын

Getting 'STM32F103RET6_creality'" terminated with exit code: 1. Not sure what has changed since April. I'm running a Windows 10 Enterprise and I just turned off Powershell 2.0.

@TheKaluNaama 2 жыл бұрын

Ya think it's normal that my Ender 5 Pro I got few days ago, shipped with a 1.1.5 mainboard?? That's 8 bit right? I couldn't even install the BLtouch with these instructions.. EDIT: ok I read online that it is still possible to receive older stock with 8 bit boards. That figures, as I got this on sale for 270€ (about 320 bucks) from Creality Europe shop, and nowhere there does it promise that the board is 32-bit. So I got that going for me, which is not nice. I guess I gotta invest extra to get a replacement board.. I suppose there are benefits for having 32 bit??

@1science100 Жыл бұрын

Sadly my Ender 5 Pro became completely useless although it was entirely and perfectly working upgraded to CR-Touch with RUNout sensor and Bugfixed Marlin 2.1.x version, when I decided to just remove the glass hotbed plate and replace it with the Twotrees magnetic plate. Re-Calibrating went perfectly and everything worked fine and an object was nicely printed. But after my Ender 5 Pro(blem) printer was switched off after the calibration first was stored and powered back on it behaved very erratic and the bedleveling didn't work anymore as expected because the Z-height was wrong. (Maybe because there apparently is no eeprom file on the SD card anymore after the new firmware was made and installed?). And when trying to adjust the Z-offset the nozzle crashed and also destroyed my brandnew 30 euros Twotrees plate. Nowhere is a correct answer given on how to solve this very annoying Ender 5 Pro problem. Which also started giving E1 heater reset problems while trying to print with PETG filament at 255 degrees Celsius. About 4 days ago before I had replaced the glass Creality plate everything worked without any worries and as a sunshine! Now I became so frustated after hours of trying to solve the issue that I had completely disassembled my useless Creality firmware unsupported Ender5 Pro(blem) printer that I had put everything back in its box. And when there is no clear solution to this problem, Creality never will be my 3D printer brand anymore! And I am very sure that many other frustrated Creality Ender 5 Pro buyers encountered the same issue that made them cursing Creality for their extremely bad and useless support!

@1science100 Жыл бұрын

I finally solved the extremely difficult to find Z height bed level problems with my Ender 5 Pro! I noticed that bedleveling only worked when I put a thin about 0.3mm sheet of paper under the probe of my CR-Touch! But just raising the bed with about that height of 0.3mm never helped! But by loosening both screws that hold CR-touch and nozzle fan holder cap and repositioning the CR-touch as low as possible and thightening the screws afterwards completely solved this crazymaking problem! So I never knew but sadly it is possible to mount the CR-Touch a little bit too high after your Ender printer never behaves normal anymore after that!

@TheNikkilou59 Жыл бұрын

Hi I have the 4.2.2 board. I followed along just fine until it was time to build. When I selected the alien head icon for PIO there was no option for Project Tasks. The first option is PIO Home, no tasks, so no board configs. I saw there were a few other people having the same issue in the comments and fixed by downloading the marlin auto build extension. This left me with the comment "The workspace doesn't contain a )valid) Marlin 2.x project". Can anyone tell me where I'm going wrong?

@zachbeatty6196 Жыл бұрын

Did you end up find it? Im having the same issue

@serenitix_official 3 жыл бұрын

I`ve followed all your instructions, while doing mine a bit different. In my Ender 5 Pro i`ve got an 1.1.5 Board and i am having trouble when it comes to the point where i have to Build in marlin. Are you able to tell under which processor i should build it in that case?

@AuroraTech 3 жыл бұрын

I don't have a v1.15 board, but Creality 8-bit V1 board should be using an ATMEGA1284P chip, so the motherboard should be BOARD_MELZI_CREALITY, when you compile firmware, the project task should select ATmega1284P.

@evanakai5604 2 жыл бұрын

Great job I have a questions after following your steps to editing at PIO but I do not have the menu project task. Hope you can help, where I can to build the code. Thank you!!

@killerjackg1 2 жыл бұрын

if you're still having problems I found another extension called auto build marlin and that allowed me to build the code

@cirruspruchnicki5795 2 жыл бұрын

Does any one know the best setting for retraction on a ender 5 pro I get stringing all the time becuse I have to turn retractions off and if I have It on the the fillement will jam up in the boden tube and fail to print

@AuroraTech 2 жыл бұрын

If you can print only with retraction off, your nozzle or something inside the heated block is still clogged or the tip of your Bowden tube is melted inside the hotend. The fix is simple, try to replace them with a new set MK8 hotend and a higher melting point Capricorn Bowden tube: MK8 Hotend: amzn.to/3s0Krfd Carpicorn Bowden tube for Ender-5: amzn.to/3OI9q0F

@taylorgrissom4250 2 жыл бұрын

Could you please supply the firmware you use for the core XY ender 5pro with the CR touch ABL... i have been dealing with non stop firmware errors... and im getting really sick of it. ive tried the first... as many as i can find to help and nothing is doing the tri... -_- ... trouble i am running into is the a ''DEFFINITION OF MACRO 'MMM_TO_MMS' #DEFINE MMM_TO_MMS(MM_M) FEEDRATE_T(STATIC_CAST(MM_M / /60.0F) ...

@earlytech2936 3 жыл бұрын

Great video. Made the same upgrades and you with all the same parts. One thing after building and updating Marlin, I'm getting a EEPROM error every time I turn it on. How do I fix that?

@AuroraTech 3 жыл бұрын

You can go to LCD menu, select configuration and restore defaults.

@jaequanswint3689 3 жыл бұрын

im getting this error also? I tried to restore defaults but still no success.. any further help? thanks

@brianj.7466 3 жыл бұрын

I think I found your issue. Your SD card (which likely still contained the firmware .bin file) was still seated in the printer, correct? So every time you went to turn it on, the printer was flashing the firmware, thus removing any setting you had prior.

@riccardoalfrilli 2 жыл бұрын

Hello, i was trying to follow your instructions for an ender 3v2 with motherboard V422. but after flashing my firmware using the autohome doesn't make the extruder go down to the bed. and using the z offset to set the level make the extruder only go up(no matter if the value is positve or negative).

@Logix727 2 жыл бұрын

ya i got the same issue. how did you correct? UPDATE ::: breadboard cables were loose was my issue!!!!!

@chickavuboo 2 жыл бұрын

Hey, is there any way u can help me with 3D Touch? The firmware now have v4.2.2

@WTFTeddyxHD 2 жыл бұрын

Same problem

@RonSamson 2 жыл бұрын

I have the 4.2.2 board. I followed along just fine until it was time to compile. When I selected the alien head icon there was no option for Project Tasks. The first option is PIO Home, no tasks, so no board configs. I tried the Boards option, but there is no STM32 board with Creality as a choice. So I am stuck at the "go to compile" step. Any suggestions?

@Logix727 2 жыл бұрын

also stuck there how to fix

@ThePaulfa 2 жыл бұрын

I had the same issue, adding the 'Auto Build Marlin' extension to VS Code resolved it for me.

@Logix727 2 жыл бұрын

@@ThePaulfa ah yes this is the answer i ment to come back and reply thank you

@Logix727 2 жыл бұрын

@@ThePaulfa i since moved to th3d

@perthling 2 жыл бұрын

I'm attempting this more than a year since your video, and presently when trying to build the firmware the error indicates STM32F103RET6_creality isn't compatible with BOARD_CREALITY_V4 "Error: Build environment 'STM32F103RET6_creality' is incompatible with BOARD_CREALITY_V4. Use one of these: STM32F103RE_creality, STM32F103RE_creality_xfer, STM32F103RC_creality, STM32F103RC_creality_xfer, STM32F103RE_creality_maple"

@TheNikkilou59 Жыл бұрын

Have you found a solution for this yet? I am having this exact error.

@perthling Жыл бұрын

@@TheNikkilou59 Yes! I used the Beta with config for board v4.2.4.

@poet99999 2 жыл бұрын

i did all this and now the ender 5 pro will not go UP the z axis, only down

@poet99999 2 жыл бұрын

I got it figured out... Idk what I did, I think there was a wire that came loose

@MyGreatCreation 2 жыл бұрын

wait what? I am just looking for a simple firmware update not all this complicated stuff

@PappyB52 2 жыл бұрын

I have a problem where it will not build the software I get an error that the Homing_feedrate_z was not declared in thei scope. and asks if I mean homing_feedrate_MM_M. I assumed that feedrate replaced speed but it just will not build. I also was wondering if you have advice on adding in DDX / 50w heater / 300c thermoster? I have these but can not find anywere that shows how to change the firmware to make them work.

@Logix727 2 жыл бұрын

what did u change to fix?

@PappyB52 2 жыл бұрын

@@Logix727 I never found a fix for it. My ender has essentially been sitting since I got it. Expensive paperweight….

@Logix727 2 жыл бұрын

@@PappyB52 I just got it fixed you need to leave the line the same as the default config and it just work s the newere firmware does not have a line for "homing_feedrate_z" mine wass somethng like 4*60

@robymartini 2 жыл бұрын

❤️❤️❤️

@conorjohnson1332 3 жыл бұрын

I followed these steps completly. but when i select autohome my hotend and bltouch auto home to the centre but my bed doesnt move. any advice ?

@AuroraTech 3 жыл бұрын

Can you move the Z-Axis up and down manually using the LCD menu? If you can ONLY move the bed down(away from the nozzle) but not up, you may need to adjust the endstop_inverting inside configuration.h, as the end stop is sending a false signal to the board so it assumes it's always triggered so it won't let you move closer to the nozzle. Search for Z_MIN_ENDSTOP_INVERTING, change the value to true or false to invert the current logic. Please try this first and see if it works.

@AuroraTech 3 жыл бұрын

Or you may download the firmware that I compiled in this video and see if this works on your printer, please adjust your Z-offset as mine was set to -1.5mm. auroratechchannel.com/download/EP08.zip (Use it at your own risk) My Ender-5 Pro is using a v4.2.2 motherboard. The manufacturer may change the hardware from time to time without notice, even you purchased the exact same printer, there is a chance that the hardware may not be the exact same, the firmware works fine with my printer, but I may not able to guarantee it also works with yours. You may also take a look of my configuration.h and configuration_adv.h: auroratechchannel.com/download/EP08-Config.zip Hope this information can help.

@absoluto2h 3 жыл бұрын

@@AuroraTech hi aurora I'm having the same issue as Conor johnson, my bed is not moving and it is only going down not up. I've tried changing the Z_MIN_ENDSTOP_INVERTING and changing its value from false to true and also tried your zip files, the problem still exist. do you have any idea what is causing this? please let me know. thanks

@absoluto2h 3 жыл бұрын

hi conor, im having the same problem as you. did you get yours fixed?

@AuroraTech 3 жыл бұрын

Are you using the same Creality v4.2.2 motherboard with TMC2208 stepper drivers? If the bed can only move away from the nozzle(down) but not up, that means the end stop is triggered all the time. You may also try: #define Z_MIN_PROBE_ENDSTOP_INVERTING false (or true) //#define MIN_SOFTWARE_ENDSTOPS (comment out) //#define MAX_SOFTWARE_ENDSTOPS (comment out) If this still not work, you can email you configuration.h and configuration_adv.h to auroratechchannel@gmail.com I will compile your firmware and upload to my Ender-5 Pro to test.

@millerw2378 2 жыл бұрын

Awesome! But sometimes I wonder if your real or artificial Intelligent robot. I mean that in a good way!

@Sluttyboy92 3 жыл бұрын

Hi, I have a Ender 5 Pro with Creality 4.2.2. 32 bit board. I have watched your video numerous times and it is very helpful however, after a successful build the file is created as a internet based .bin file and a non internet based .elf file. I have rebooted and tried several times on a clean slate with no success on uploading the firmware on the printer. HELP PLEASE!!!!

@AuroraTech 3 жыл бұрын

Let's try this: Download the official Creality firmware and try to upload, if it works, the problem is your bin file, if not, the problem may be the bootloader of the motherboard.

@Sluttyboy92 3 жыл бұрын

@@AuroraTech Thank you so much for your response. I have tried this over and over and it's not working. I am thinking the problem could be my computer is not recognizing the bin file. It keeps converting it to a notepad file but .bin? Is there a way to make a correction within the computer?

@cynthiadelavega7848 Жыл бұрын

Could I pay you somehow , to help me fix an Ender 3 that I purchased on offer up please?

@cynthiadelavega7848 Жыл бұрын

I have a profile on eBay, with which we can maybe complete a transaction of some sort? Maybe if you load an de card with all proper files and firmware . CREALITY ENDER 3 motherboard V4.2.2 .

@cynthiadelavega7848 Жыл бұрын

PLEEEEEASE😫🤯😤😭

@AuroraTech Жыл бұрын

Actually, it's difficult to troubleshoot the machine if I have no physical access to it, in many cases, you also need some extra spare parts for testing.

@rockss 2 жыл бұрын

what am doing with my life if i cant do what you're doing?

@jjpaulericksonviernes5615 2 жыл бұрын

hi,, i dont know why, but i always got so many error

@jjpaulericksonviernes5615 2 жыл бұрын

{ "resource": "/d:/Costumer All/ciane xavier/Marlin-2.0.x/Marlin-2.0.x/Marlin/Configuration.h", "owner": "C/C++", "code": "1696", "severity": 8, "message": "#include errors detected. Please update your includePath. Squiggles are disabled for this translation unit (D:\\Costumer All\\ciane xavier\\Marlin-2.0.x\\Marlin-2.0.x\\Marlin\\src\\inc\\Warnings.cpp).", "source": "C/C++", "startLineNumber": 1, "startColumn": 1, "endLineNumber": 1, "endColumn": 1 } { "resource": "/d:/Costumer All/ciane xavier/Marlin-2.0.x/Marlin-2.0.x/Marlin/src/inc/Conditionals_post.h", "owner": "cpp", "severity": 8, "message": "'Z_MIN_POS' was not declared in this scope; did you mean 'Y_MIN_POS'?", "startLineNumber": 96, "startColumn": 38, "endLineNumber": 96, "endColumn": 38 } { "resource": "/d:/Costumer All/ciane xavier/Marlin-2.0.x/Marlin-2.0.x/Marlin/src/inc/Conditionals_post.h", "owner": "cpp", "severity": 8, "message": "'Z_MIN_POS' was not declared in this scope; did you mean 'Y_MIN_POS'?", "startLineNumber": 253, "startColumn": 42, "endLineNumber": 253, "endColumn": 42 } and more