6.2 Intake Manifold and Throttle Body Install on a 5.3 - 2014-2018 Silverado Sierra Tahoe Yukon

Рет қаралды 185,722

Күн бұрын

Welcome back guys! We are one step closer to getting some final dyno number for my 2014 Silverado.
In this video we are showing how to install 6.2 Intake Manifold and 6.2 Throttle Body. Be Sure to check out the part links from below.
This installation should work for the following vehicles but always double check for your specific model.
2015-2020 Tahoe
2015-2020 Yukon
2015-2020 Suburban
2014-2018 Silverado
2014-2018 Sierra
Note: The Performance Driveline driveshaft is currently not speed rated - only HP rated but it should be able to handle the higher speeds.
👉🏼 LINKS TO PURCHASE TOOLS & PARTS FEATURED BELOW👈🏼
#6.2ThrottleBody #SilveradoDIY #6.2IntakeManifold
⚠️Try anything shown in this video at your own risk ⚠️
********************************************************************
Associated Videos - AFM DOD Delete Series
********************************************************************
Full DOD delete series below:
Part 1 - Baseline Dyno: • AFM Delete Part 1 - Wh...
Part 2 - What Parts Do You Need • AFM DOD Delete Part 2 ...
Part 3 - Engine Removal: • AFM DOD Delete Part 3 ...
Part 4 - Engine TearDown: • AFM DOD Delete Part 4 ...
Part 5 - Installing New Parts: • AFM DOD Delete Part 5 ...
5A - Cam Phaser Install: • AFM DOD Delete - How t...
5B - Trunnion Upgrade: • How To Upgrade GM Trun...
5C - Lashing HP Fuel Pump: • How To Properly Lash H...
5D - Injector Seals • High Pressure Fuel Inj...
Part 6 - Reinstalling Engine: • AFM DOD Delete Part 6 ...
Part 7 - Tuning and Dyno Run:
Part 8 - Installing Intake Manifold, TB, Air Intake, & Driveshaft:
8A: AIRAID Intake: • Silverado 6.2 AIRAID I...
8B: 6.2 Intake Manifold and TB: • 6.2 Intake Manifold an...
8C: Drive Shaft: • 2014-2018 Silverado Dr...
Part 9 - Tuning and Final Dyno Run:
************************
🔩Parts (Affiliate Links)
************************
For the parts needed to delete AFM check out: • AFM DOD Delete Part 2 ...
6.2 Intake Manifold and Throttle Body:
geni.us/GPI_62_IntakeManifold
You will also need GM Part: 12650610 geni.us/GM12650610 if you are not running a catch can setup. This Part is available as an optional add on through the above GPI link.
Intake Manifold Gaskets 12626354 (x8): geni.us/GM12626354
**********************
Tools (Affiliate Links)
**********************
EastWood Rolling Cart: geni.us/EW_RollingShopCart
1/4" Torque Wrench: geni.us/GW_14_TorqueWrench
Milwaukee 3/8" Ratchet: geni.us/MW_2557-20_Ratchet
Wobble Sockets: geni.us/WobbleExt
***********************************
⚙️Torque Specs
***********************************
Torq Spec 1: 89 In-Lbs
Torq Spec 2: Pass 1: 44 In-Lbs Pass 2: 89 In-Lbs
******************************************
🎬 Recording equipment (Affiliate Links)
******************************************
📷 Video
Canon EOS 80D Digital SLR: geni.us/Canon-EOS80D
----------
Thank you to all of our fans and subscribers for supporting us on our journey!
FOLLOW US ON INSTAGRAM: @THESUNDAEDRIVE
CHECK OUT OUR WEBSITE & BLOG: www.thesundaedrive.com

Пікірлер: 249

@miguel9532 2 жыл бұрын

BEEN WAITING FOR THIS BUILD TO BE FINISHED

@TheSundaeDrive 2 жыл бұрын

We are getting close!! Took way too long lol

@FirstLast-we8cb 2 жыл бұрын

Good vid!

@TheSundaeDrive 2 жыл бұрын

Thanks!!

@Punk-Jw 2 жыл бұрын

3:00 I can agree with all of that. Mines a 15 on z rated 22's but you can still feel in the driveline it doesnt like it. I've had it up to 140 once but thats more than pushing it, I dont recomend anyone cruise much more than 110 for very long without a driveshaft upgrade! I've seen ones in the 2500 gas trucks even rip in half just easing threw the woods...transfercase, fuel tank, lines, evap and a new driveshaft (anyway) later... 🤷‍♂️ it costs to go fast if you have any plans on walking away lol

@pat14lang Жыл бұрын

I’m doing this mod to my truck this weekend. Next mod on the list will be upgraded driveshaft. Then a BTR stage 2 w/AFM delete and trunnion upgrade.

@JMRxYM Жыл бұрын

I just had my 2014 single cab 5.3 built with the btr stage 2, ls7 lifters and valvetrain with dod delete, 6.2 intake and TB, LT4 fuel pump and injectors. This truck now chirps into both second AND third, runs insanely well for a daily driven street truck.

@JMRxYM Жыл бұрын

These 5.3s make 380/420 on e85 and the cam alone is supposed to pull 70HP out of the L86 (6.2) so I’d assume probably 50ish on the L83 (5.3). Then the intake and fueling upgrades probably another 30-50 depending on tune. I’m probably sitting at about 425-430 to the wheels after it’s all said and done. You lose a little low end with the cam but what you gain from 3500-6000rpm is insane. It pulls the exact same through the entire powerband. Just shits and gets. I have videos if you want proof lol

@pat14lang Жыл бұрын

Share the video on youtube. Where I live, their is no places that I know of or can find that have E85 :\

@blakeedwards1730 Жыл бұрын

any suggestions on an aggressive but drivable cam for the l83(5.3) and maybe the valves i’ll need

@pat14lang Жыл бұрын

@@blakeedwards1730 I was suggested BTR stage 2, Johnson lifters, chromoly push rods, and conical dual spring kit. Nice HP and torque gain, still drivable with stock TC and can still tow with it. I plan to go with this “AFM delete”…

@jagoss45 2 жыл бұрын

I just put a Specter Performance intake and filter to my 6.2 and WOW does it make it sound good when that pedal goes down! I also have a MBRB. Cat back SS exhaust which makes for a great combo. I have not towed my camper with the intake yet but looking forward to a little more power.

@TheSundaeDrive 2 жыл бұрын

Ooo nice. The airaid I added sounds fantastic. Looking forward to driving with it regularly. Haven't done an exhaust yet. Probably next year for that.

@angelmarquez6000 2 жыл бұрын

Make a video of it! Man that sounds good

@JTrump23 2 жыл бұрын

@@TheSundaeDrive I have the Airaid air intake on mine for the 5.3L. If I were to upgrade to a 6.2 intake manifold, would I need to get a bigger coupler or would the one I have for the 5.3 work? Thank you in advanced

@TheSundaeDrive 2 жыл бұрын

I believe you can manhandle the 5.3 coupler onto the 6.2 throttle body. Not easy but I've heard it can be done.

@brianraabe308 2 жыл бұрын

@@JTrump23 I have the airaid Jr with the 6.2 l tb and intake and I was able to stretch it over the new intake. It's a job and you may need some lube but it can be done... I ended up ordering a 4"to 4" coupler on Amazon that's a little bit oversized for the intake but when you tighten the clamp, it seals it and your not able to pull it off. I was afraid of the 5.3l coupler splitting as it gets older.

@grahamwhittington4444 2 жыл бұрын

Did this to my 15 Silverado. Picked up power for sure down low. Plus I have some other mods. Let me just say it would love some e85

@TheSundaeDrive 2 жыл бұрын

Yeah man, I might give e85 a go at some point for fun. Thinking about meth tho

@grahamwhittington4444 2 жыл бұрын

@@TheSundaeDrive ahh I’ve heard good stuff about meth on these trucks as well! Thanks for the great Silverado content! Learned a lot from your channel

@351cleavland 2 жыл бұрын

@@TheSundaeDrive I wouldn't recommend it. Likely it will ruin your teeth!

@greglentz3303 Жыл бұрын

2017 5.3 failed…Lifters of course! And camshaft damage. Going to attempt to do it myself,However, could use some detailed info on programming! Great info and videos from you! Would have not considered this without TSD.Thanks !!!

@TheSundaeDrive Жыл бұрын

We may do some tuning videos in the future. We used a remote programmer for my truck but you should really add a wideband sensor (which we did and will be making a video about). Shoot us an email through our website www.tsd-motorsports.com and I'll be happy to put you in touch with the guy we used.

@toddhargett2135 2 жыл бұрын

been running the 6.2 intake manifold for awhile the difference is it has longer runners that allow for more torque and yes the opening for the throttle body is bigger also you will like it for your towing

@TheSundaeDrive 2 жыл бұрын

Awesome! Looking forward to getting it tuned and seeing what she will do

@toddhargett2135 2 жыл бұрын

I don't think the peak hp or torque will be a ton higher but it will have a better range and will definitely work well for you because it should be more lower to mid range I did the 6.2 intake manifold and tbody cat back and intake and then tuned it for e85 and made about 60ish hp more I think? I'd have to check the dyno printout it was about 2 years ago haha but it's nice alot more fun to drive but now my torque converter went out :( so I'm pulling it all apart having the trans built and camping the motor doing basically what you did minus the 6.2L heads 😜 haha

@TheSundaeDrive 2 жыл бұрын

Haha yes don't do the 6.2 heads 😅

@97JoMiller Жыл бұрын

Did you have to tune it or anything?

@TheSundaeDrive Жыл бұрын

No tuning is required from my experience

@j_rod75 2 жыл бұрын

I did this mod about 3 weeks ago. Took half a day taking my time. I also installed a cold air intake (not the same as this one shown) hardest part was the plastic tabs in the back. Pissed me TF off but I got them and didn’t put the cover back in. Same MAF, No tune and have not gotten any codes.

@TheSundaeDrive 2 жыл бұрын

Awesome! glad it is working out well for you! Those tabs at the back are terrible. really bad design.

@garygrunst140 2 жыл бұрын

You need that when the lifters fail and take out the cam. Lol

@TommyLGarage 2 жыл бұрын

So easy!!!

@TheSundaeDrive 2 жыл бұрын

Haha yup! Thanks man

@Danielbrito22 2 жыл бұрын

I got a check engine light on my truck I just did the swap any tips it’s in tuned says engine power loss I also added a lt5 tb

@antoniomartinez8253 Жыл бұрын

What else is differente between the 5.3 and the 6.2? I look at both the motors and they look the same

@alexandercano5314 2 жыл бұрын

Question, Where can i buy after market parts like superchargers or cams all that good stuff?

@nmtz91 2 жыл бұрын

One question I have a catch can I believe I don’t need the pcv valve house right

@ManuelRamirez-od7tm Жыл бұрын

Cant find the video on how to remove the cover for the manifold cover

@tyschultz6053 9 ай бұрын

Can this swap be done using the stock l83 airbox or is a larger diameter needed?

@brodywoodard2069 6 ай бұрын

i have a 2014 5.3l ecotec3 Gen 5 with AFM, ive been on GPI and i cant find a delete kit specific to them, they only have up to gen 4 could anyone help me out? Thanks

@TheBossXVI 2 жыл бұрын

👍👍👍

@moody31699 19 күн бұрын

I am not seeing the link on how to get that cover off with the high pressure fuel pump can you please post it?

@l.a.m7645 2 жыл бұрын

Can this be done on a 2021 5.3L Sierra?

@kingwilly1000 2 жыл бұрын

Who did the tuning of the intake manifold?

@josh_a.7142 2 жыл бұрын

Will this work on a 2001 6.0 Silverado?

@chrisp8395 2 жыл бұрын

About mass air flow sensor you use the 5.3 one or you install different one? 🤔how much more power with new upgrades?

@TheSundaeDrive 2 жыл бұрын

You can use the same MAF. The shop I was using to tune unfortunately closed so I havent been able to get on a Dyno yet to test out the power gains. Trying to add a wideband to the truck soon so I can finish getting the tune done and then I need to find a Dyno shop.

@737mechanic 2 жыл бұрын

I would like to see some numbers to see if this would actually be worth it.

@TheSundaeDrive 2 жыл бұрын

GPI has some in depth dyno testing results you can see up on their site - planning to dyno but we've been slammed.

@ninjaface2342 Жыл бұрын

@@TheSundaeDrive Gpi does horrible work. I wouldn't let them change my oil. Tune on my freinds truck was so bad. Tore up two transmissions and he had it tuned by someone else and got more than 100 more hp. They suck. Another freind had a cam installed and the motor tore up soon after. He had to replace the engine.

@ninjaface2342 Жыл бұрын

@@TheSundaeDrive First freind got a full refund from them to be quiet about it and they told tge second dude..."tough luck"

@pat14lang Жыл бұрын

Look up Richard Holdener. He has several videos with Dyno charts for the L83 stock, BTR cams 1-4, L86 intake swap stock, and L86 intake swap with BTR cams 1-4

@TheSundaeDrive Жыл бұрын

I can't speak to their installation work. Only have dealt with them for parts but I would be frustrated by that for sure!

@dixbuiltit1293 2 жыл бұрын

LT1 intake is a option as well, I’m doing a LT1 on my L83 build

@TheSundaeDrive 2 жыл бұрын

Nice! Is there any difference between the lt1 manifold and this?

@daringlisson9353 2 жыл бұрын

The throttle body intake is angled down on the LT1

@dixbuiltit1293 2 жыл бұрын

@@daringlisson9353 correct, ICT billet makes a angle adapter or you can reroute your serpentine belt to make It work

@dixbuiltit1293 2 жыл бұрын

@@TheSundaeDrive as far as power, not 100% sure, you would think it has good numbers being a corvette intake. I’m using it for the look more than anything

@TheSundaeDrive 2 жыл бұрын

It does look cooler for sure

@anthonymacneil2279 2 жыл бұрын

Did it make any difference? I have a 6.2L

@papaaasanti8632 2 жыл бұрын

Does that drive shaft handle over 500hp??? How much was it ? Can I get the link ?

@Coletrain0128 7 ай бұрын

I am soon to be doing the AFM delete stage 1 and cylinder exactly as you did. Do you recommend using stock intake for the tune or should I put the new 6.2 manifold on to get it tuned? Thanks!

@TheSundaeDrive 7 ай бұрын

If you can get the 6.2 cheap, go for it. Just make sure your tuner knows.

@VAlien79 Жыл бұрын

I did the swap, everything bolted up great then I noticed a extra vacuum line port on the drivers side rear that was not in the l83 manifold? It through codes and ran lean I plugged it with a cap and codes Cleared up and it runs great???? But I’m stumped on the extra port in the l86 manifold

@TheSundaeDrive Жыл бұрын

I am very curious as well now. So much so I got up to go look at mine to see if I could see an extra port lol. Needless to say I could not find one. Was it definitely an L86 intake manifold you got? could you send us a photo of the port to our instagram instagram.com/thesundaedrive

@Zacatecano48 2 жыл бұрын

After you swapped the intake manifold and throttle body did you have to do any running or does it run just fine?

@Jose-ew6hj 8 ай бұрын

Should run fine , would recommend a tune to get the full potential of it

@97JoMiller Жыл бұрын

I just did the 6.2 swap last night. I noticed the truck is idling a bit rough now. It's a totally stock tune and I just got my tuner last night so I'm waiting on the tuner to make the changes. It just seems odd that the final pass with the torque wrench is 7.4lbs... it feels un-natural lol

@TheSundaeDrive Жыл бұрын

Lol it doesn't take much. Keep us posted for sure! I know my truck had a custom tune already but it was made for the stock intake manifold and I swapped this one on I didn't notice any issues. My truck was already idling rougher from the cam tho so might have just been too subtle to feel or see lol

@97JoMiller Жыл бұрын

@@TheSundaeDrive lol, ya a cam will do that to you. I also did that thermal thing for the transmission and my fluid is brown (did it at the same time as the intake) so I guess I need to order a filter and fluid and that'll be the next project that I get to do... also gotta go pick up a 2x4 to pull down the exhaust to get that pan out. Fun times!

@TheSundaeDrive Жыл бұрын

Always fun. :) Lol

@Luizmtz5.3 Жыл бұрын

Would this work for a 07-13 Silverado?

@dennisschneider9670 Жыл бұрын

Has this been dyno to see if it's better?

@devin7224 3 ай бұрын

i thought the speed limiter was due to the tires that come factory not the drive shaft. does trim make a difference in drive shaft speed

@TheSundaeDrive 3 ай бұрын

Tires can effect it as well

@jessearnett2639 Жыл бұрын

Anyone done 6.2 injectors in a 5.3 with the intake swap?

@jonmmarquis777 2 жыл бұрын

Did this mod on my 17 silverado.

@TheSundaeDrive 2 жыл бұрын

Awesome! How do you like it?

@pat14lang 2 жыл бұрын

Nice! I thought about doing the same to my ‘17

@TheSundaeDrive 2 жыл бұрын

An easy mod for sure.

@Bird-dl7xs 2 жыл бұрын

What years does this work on the hood to put it in the service position? Does the 07-13 have the same thing?

@TheSundaeDrive 2 жыл бұрын

Mine is the next generation but many hoods have a service position. It probably does but you'll need to check and see if it has holes similar to mine

@pritt2933 Жыл бұрын

At 5:06 what is the you disconnected? My truck was in the shop the other day and someone didnt reconnect it. In still learning everything in my truck I have a 14 Silverado

@TheSundaeDrive Жыл бұрын

That's part of your pcv system

@codyanddesiraewilbur6067 2 жыл бұрын

Great video series I followed your cam swap series and they were a great help in installing my cam on my 15 Sierra l83. I recently finished everything up had my ECM tuned and I am getting error codes for coil control circuit on cylinders 1,3 and 5 I’ve moved plugs and wires around checked for loose connections including the two grounds on the drivers side head. Just curious if you had heard of anything like this or had any insight to what could be going on? Thanks again for the great videos.

@TheSundaeDrive 2 жыл бұрын

Glad the series helped! I haven't had this particular issue. I think I saw this issue you posted on FB. That could be a tuning issue. Did you talk to the shop that tuned everything for you?

@codyanddesiraewilbur6067 2 жыл бұрын

@@TheSundaeDrive I spoke with the shop that tuned the ECM, he stated that it seemed to be a power/ground issue. Thanks for the reply and thanks again for the awesome series.

@TheSundaeDrive 2 жыл бұрын

It could be a grounding issue for sure. There are a ton of grounds and it is very easy to miss one. If you can report back when you figure out the issue that would be awesome tho :)

@codyanddesiraewilbur6067 2 жыл бұрын

@@TheSundaeDrive I wound up finding a nicked wire on the number 2 coil fixed that and removed the intake manifold refitted the grounds at the back of the heads and the plugs to the fuel injectors and the high pressure fuel pump issue codes were gone went for a test drive and had a flashing engine light only when accelerating found a cracked plug, swapped that and everything is good now. Thanks again for all the help.

@TheSundaeDrive 2 жыл бұрын

Glad you got it figured out! And glad it was something simple

@rogerjohnson4998 Жыл бұрын

I know nothing about this stuff lol but anyways! I have a 2018 Silverado Z71. I put a 2” leveling kit on with bigger wheels and tires which are 285/55/20’s and of course 20”x9” wheels. Now I’m putting a Borla s-type exhaust on with a corsa cold air intake. What benefits would I get with putting this on my truck? Really I know nothing about this kinda of stuff.

@TheSundaeDrive Жыл бұрын

Here is a video we made that show the Dyno gains! Mainly just helps with a little more power and torque kzfaq.info/get/bejne/m7GpaJWj3N66lYk.html

@codyjones5535 2 жыл бұрын

Cut the back off worked great for me! Those clips on the back suck. I didn’t like the constant air noise with cylinder switches from 4 to 8.

@TheSundaeDrive 2 жыл бұрын

Those clips are a pain. I deleted afm so no more of that for me :)

@atruceforbruce5388 Жыл бұрын

Anyone knows if this kind of mod would work on a 2017 5.3 tahoe ? Also does it make any more horses than if not modified?

@TheSundaeDrive Жыл бұрын

Should increase torque a bit and I believe it should work but have not done it to he sure.

@rubennogueras2139 Жыл бұрын

Can you send me your video of you taking off the TRUCK MANIFOLD ENGINE COVER. It's very hard for me. It's the first top cover that is on top of everything. Thank you

@TheSundaeDrive Жыл бұрын

We have a video showing how, look up the hpfp fuel pump replacement we filmed on the truck. We remove it in that video.

@stevenstair1068 2 жыл бұрын

Whats the cost of this up grade?

@luisperez-xd5mo 2 жыл бұрын

Did you had the ecm tune after swapping the manifold intake and tb?

@pat14lang Жыл бұрын

Not needed but can be helpful

@jr_NorCal 2 жыл бұрын

Swappin that, will it drop a check emgine light or anything??

@TheSundaeDrive 2 жыл бұрын

I don't believe so but my truck has a custom tune so I can't guarantee it. To get the best performance out of it you'll want it to be tuned for the additional airflow. 99% sure others have done it without a tune tho, if you search around online you should be able to see pretty quick.

@glennhamilton8894 2 жыл бұрын

Been looking at doing this mod on my 18' Silverado. I work at a GM dealership as a tech helper, so relearning the tb position isn't that big of a deal, but would it work without a custom tune

@j_rod75 2 жыл бұрын

I did this on my 15 Silverado. I didn’t do a thing for a tune and never had a check engine light

@sambo2891 2 жыл бұрын

@@j_rod75 did you get any gains?

@j_rod75 2 жыл бұрын

@@sambo2891 yes but nothing that really wowed me. I decided to get a custom tune so hopefully this month I have good news.

@OscarMartinez-dy2sh 2 жыл бұрын

@@j_rod75 ill be waiting on the overall results if you dont mind replying

@j_rod75 2 жыл бұрын

@@OscarMartinez-dy2sh I don’t mind at all. I had to reschedule the appointment so when they can get me in I’ll let you know

@joseduranjr4963 2 жыл бұрын

Can you please tell me if the 2017 GMC Sierra DENALI with the 6.2 is a direct injection engine? Thank you

@photojunky7342 Жыл бұрын

Yes it is

@TheSundaeDrive Жыл бұрын

Agreed

@atruceforbruce5388 Жыл бұрын

Sad there is not much an aftermarket scene, or performance upgrade scene or anything for the chevy tahoe.

@TheSundaeDrive Жыл бұрын

Harder to find but mods are out there for sure.

@jayer-su3hu 2 жыл бұрын

So can I buy the 6.2 intake and TB and I stall on my 5.3 and drive with no other mods and no tuning? Basically plug n play or no? I would think the ECU would see something different and throw 5000 codes or something

@j_rod75 2 жыл бұрын

I did this a few weeks ago. No tune and no codes.

@jewllake 2 жыл бұрын

@ 1:12 seconds did some get hammer happy with the metal door on the left? LOL

@TheSundaeDrive 2 жыл бұрын

It was a victim of doormestic violence

@yami4g63 2 жыл бұрын

hahaha you can get to the injectors, but the real question is will they come out...........haha even with the special gm tool was a nightmare.

@TheSundaeDrive 2 жыл бұрын

They are a nightmare. I bent a fuel rail trying to get them out working super carefully. They added a gasket on the newer engines that helps them from siezing but doesn't fully prevent it. On the other side I just removed the fuel rail and got new injectors since I was changing the heads 🤣

@jonathansimpson1106 11 ай бұрын

I thought the computer would only allow the amount of air that the engine need no matter the intake size???

@williamdavis4809 2 жыл бұрын

Plastic fantastic

@ulisesjaramillo9019 Жыл бұрын

Does anyone know if the 2020 model 6.2 intake will fit a 15’ 5.3

@TheSundaeDrive Жыл бұрын

Unsure. Engine setups are different.

@Ryanmoody89 2 жыл бұрын

Now heres the big question. Can it be done to an older ls engine like a 2003 model?

@allanb3222 2 жыл бұрын

The question is why would you?The intake ports are shaped different.

@Ryanmoody89 2 жыл бұрын

@@allanb3222 the question is why not? You know more air flow and all. But looks like I'll go for 6.0 intake instead.

@allanb3222 2 жыл бұрын

@@Ryanmoody89 The tbss intake is the best flowing,stock intake for your gen III. I would go with that.

@Ryanmoody89 2 жыл бұрын

@@allanb3222 I shall look into that then. I got an 03 tahoe z71 I'm trying to do work to so whatever I can use I'll do it.

@c_capp2015 6 ай бұрын

did you disconnect the battery before you unplugged the electrical connections?

@TheSundaeDrive 6 ай бұрын

Always a good idea to!

@urairbornepapi2702 2 жыл бұрын

Can you do this with any year? I have an 04.

@TheSundaeDrive 2 жыл бұрын

Most likely if you get the intake manifold for the larger motor from your generation. Hop on the forums, I'm sure someone has done it if you can

@forgottenchild7935 2 жыл бұрын

I did this swap and the truck fired up and ran great for a minute then began to sputter and stall out.it will start right back up and sputter and stall.No check engine or pending codes. Is it the tb? should i drive it and see if it relearns?

@TheSundaeDrive 2 жыл бұрын

You probably need a custom tune for the upgrade If your truck is sputtering out. Mine is tuned and I plan to refine the time with my intake manifold and throttle body. Haven't gotten around to it because the tuner I was using closed up :(

@forgottenchild7935 2 жыл бұрын

@@TheSundaeDrive thanks for responding, that was my guess too

@TheSundaeDrive 2 жыл бұрын

No problem. Best of luck with it! Let us know how it turns out.

@forgottenchild7935 2 жыл бұрын

@@TheSundaeDrive Finally got my tune from blackbear and it turns out that my brand new upstream O2 sensor on the passenger side was damaged from the get go. This was causing the erratic idle and Blackbear was able to flag it when they read my live data log. It never set a check engine light, replaced all 4 with factory ac delco sensors and the truck runs beautiful. I'm sure once I upload the tune it will be even better. Thanks for the videos and advice'

@TheSundaeDrive 2 жыл бұрын

Oh good to know. Glad you were able to get that figured out! Thanks for following up. Surprised there wasn't a code thrown.

@AB12896 2 жыл бұрын

Is it just more air or did the ECU adjust so it adds more fuel to the mix?

@TheSundaeDrive 2 жыл бұрын

ECU should automatically adjust but I'm running a custom tune - it's probably only really worth it with a custom tune honestly

@AB12896 2 жыл бұрын

@@TheSundaeDrive gotcha, might put a 6.2 intake on mine

@TheSundaeDrive 2 жыл бұрын

Air intakes are identical, only difference is the throttle body and manifold

@theloneriderzadventures 2 жыл бұрын

Can i do this to my 13 tahoe? Do you have to retune pcm after this install or is it a turn key swap?

@sstevocamaro Жыл бұрын

The 2013 Tahoe has a gen 4 engine. This is a gen 5. You already have the best gen 4 truck intake on your 2013. It come stock with the TBSS intake. Look it up.

@ethans6.0 Ай бұрын

@@sstevocamarowhat about 04 sierra? Is a throttle body conversion worth it? Let’s say 04 throttle body to 08-13,14-18,19+?

@ethans6.0 Ай бұрын

@@sstevocamaroit’ll effect smog emissions for California too?

@hydro7715 2 жыл бұрын

@12:17 seconds what’s that and where do you get it?

@TheSundaeDrive 2 жыл бұрын

I'm not sure the name of the part but I moved it from my 5.3 intake manifold to the 6.2 manifold. I'll try to get a part number for you. It might always come with the manifold since I'm not seeing a separate part on the websites.

@bambamnicholson1 2 жыл бұрын

What kind of gains from the intake manifold swap? Looked for a vid didn't see it.

@TheSundaeDrive 2 жыл бұрын

haven't gotten around to making it yet - too much going on but it will come out later this year. The tuner I was planning to use closed shop so it set me back a bit on the remaining videos - we will get there tho!

@homeeconomics1019 2 жыл бұрын

I am very literate with car. My question is; can I swap 2018 escalade platinum 6.2 intake manifold on 2015 suburban LT?

@TheSundaeDrive 2 жыл бұрын

Does your suburban have the L83 engine?

@homeeconomics1019 2 жыл бұрын

@@TheSundaeDrive my is a 5.3, I am not sure but I think it is. It is a LT 5.3 rear wheel, where can I find out from the engine to be able to tell it is a L83 ?

@TheSundaeDrive 2 жыл бұрын

I think it is printed on the block but can also have the dealer run your vin if unsure and they can tell you your engine code. The 2015 should be the L83 and if so, the l86 intake manifold come the 2018 should be compatible.

@homeeconomics1019 2 жыл бұрын

@@TheSundaeDrive thank you very much

@patrickwarden2933 Жыл бұрын

Why not take motor mount out or just bolts to lower the engine

@TheSundaeDrive Жыл бұрын

Sorry not following? why would I need to take out the motor mount out?

@joed8842 2 жыл бұрын

Could I do this to my 2001 chevy silverado 5.3 LS

@TheSundaeDrive 2 жыл бұрын

Possibly with a different intake manifold. Not positive tho. Not sure what is different.

@steves5355 2 жыл бұрын

Grab a tbss intake, trailblazer SS...

@josh_a.7142 2 жыл бұрын

@@steves5355 will it work with my 2001 6.0 as well?

@tonyloza4002 Жыл бұрын

is there a difference in the mpg with this upgrade?

@Jose-ew6hj 8 ай бұрын

Honestly if you’re worried about mpg shouldn’t be modding the truck. When you start modding it your foot is most likely always gonna be to the floor lol😅

@warlock4reef598 Жыл бұрын

Would this work on 03-06 vortec?

@TheSundaeDrive Жыл бұрын

Unsure. Probably would be different

@Snakeplissken6 2 жыл бұрын

Where are your dyno numbers!!!!!

@239seth Жыл бұрын

Will this work ona. 2004 GMC Sierra 1500?

@TheSundaeDrive Жыл бұрын

Unsure, likely not unless it is from a larger engine from that same generation

@chevyboiii2115 6 ай бұрын

If i upgrade these two mods is it mandatory i tune or no tune requred?

@TheSundaeDrive 6 ай бұрын

I am not a tuner so take this with a grain of salt but I ran these for while with no modifications to my tune and has no problems so from that experience I don't believe a tune is required. A tune will help you get the most power from the upgrade tho

@chevyboiii2115 6 ай бұрын

@TheSundaeDrive it's it much appreciated for ur reply man thanks for much help ur channel helps me alot ⚡️⚡️😎

@TheSundaeDrive 6 ай бұрын

@@chevyboiii2115 no problem! Glad to hear it!

@frankyq21 Жыл бұрын

will this work for the 2017 1500 5.5?

@TheSundaeDrive Жыл бұрын

I'm but familiar with the 5.5 engine. If you meant 5.3 then yes it will work

@hakaiytg9699 Жыл бұрын

Will the 6.2 fit on a 4.8?

@bk2life Жыл бұрын

yes exact same engine

@badassjeep1 2 жыл бұрын

Much better swap is to sell the 5.3 and buy a 6.2

@TheSundaeDrive 2 жыл бұрын

Lol if this motor goes I will be. Not a simple plug and play swap from what I understand but I imagine one day I'll be doing it :) not getting rid of the truck

@TheSundaeDrive 2 жыл бұрын

Wanted to focus on upgrading the 5.3 as most drivers have that, very few would be willing to do a 6.2 swap

@JTrump23 Жыл бұрын

@@TheSundaeDrive Great video! I have the same Airaid for my 5.3L. Would you happen to know the size of that coupler for the 6.2L manifold. I’m trying to get ready for the swap and don’t have the 6.2L coupler … any advise on where to purchase one that would fit? Thanks

@TB-cq3zj Жыл бұрын

Sounds quite expensive vs the mods but I get your thinking. Most people do what they can afford, except politicians, they just raise the debt ceiling lol.

@waynebrod3698 2 жыл бұрын

What vehicle does the 6.2 come from?

@TheSundaeDrive 2 жыл бұрын

Also the silverado and siera from the same generation. Camaro too I think we well as some SUVs

@davidcarr4464 2 жыл бұрын

Are you running the stock 5.3 injectors?

@TheSundaeDrive 2 жыл бұрын

Yes I am

@baggedmonster 2 жыл бұрын

Where’s the dyno numbers?!

@saadghanim6727 2 жыл бұрын

does it fit on 07-2013?

@Bluntsngallos 2 жыл бұрын

Hey man I got a 4.8 I wanna put an iir intake like that on mine is this something that will fit my truck

@TheSundaeDrive 2 жыл бұрын

What year is your truck?

@Bluntsngallos 2 жыл бұрын

@@TheSundaeDrive its a 09

@Bluntsngallos 2 жыл бұрын

@@TheSundaeDrive I appreciate u replying sir 🙏 I got one more question I do wanna start putting performance parts 😅in my truck I wanna start with a cam but I'm not sure what size I would need my truck is bone stock would u no a part number and what els iwould need for that cam upgrade thanks in advance sir

@drod8816 2 жыл бұрын

Is the same the 2014 suburban

@TheSundaeDrive 2 жыл бұрын

I don't think the suburban was updated until 2015 so probably different

@drod8816 2 жыл бұрын

Yes the engine setup looks a lot different. Just wondering if I can set it up with the 6.0 setup

@TheSundaeDrive 2 жыл бұрын

Possibly but not sure

@hotrod76. 2 жыл бұрын

Well where is the test results.? 🤔

@TheSundaeDrive 2 жыл бұрын

Watch are most recent update video. I think we published it about a month ago

@user-hf1pz4og6e 5 ай бұрын

Guys when Chevy sells their vehicle they put the best package for the engines that a stock option has to offer , so swapping stock parts for more stock parts is like a wasite of time ..

@TheSundaeDrive 5 ай бұрын

I picked up hp tho. Check out the Dyno results video.

@willallen126 4 ай бұрын

You’ve never done anything with motors and it’s obvious. You can take different 212cc heads and swap those for higher compression. Higher compression means more power.

@kthomas8732 Жыл бұрын

Was it worth it????

@TheSundaeDrive Жыл бұрын

We have before and after Dyno results on the channel. I think so

@kthomas8732 Жыл бұрын

@@TheSundaeDrive oh yeah I looked at the video. Impressive numbers!!

@dominicjlesperance3328 Жыл бұрын

Is it plug and play?

@TheSundaeDrive Жыл бұрын

I did get a custom tune but I drove without a change to he tune for awhile without issue.

@dominicjlesperance3328 Жыл бұрын

@@TheSundaeDrive thank you!

@TheSundaeDrive Жыл бұрын

@@dominicjlesperance3328 no problem! Best of luck with it!

@dominicjlesperance3328 Жыл бұрын

@@TheSundaeDrive thank you for the amazing idea!

@dominicjlesperance3328 Жыл бұрын

I’m gonna sound like an idiot right now but my engines shaking and says “reduced power mode” This is really embarrassing

@brianjacobsen5762 2 жыл бұрын

Wow a 6 or 7 year old truck you cant drive over 100 because the driveshaft junk from the factory. GM makes shit. Have 98 GMC1500 Trans have problems and they still do up to the present.

@TheSundaeDrive 2 жыл бұрын

Annoying for sure