McCulloch Power Mac 6 First Run In 28 Years.

Рет қаралды 4,142

3 жыл бұрын

According to a tag that was on it, lets see if I can get her running for the first time since 1993. But first, fuel system over haul must be done.

Пікірлер: 42

@vovinh3968 3 жыл бұрын

Thanks sir! I learn so much from your teaching.

@mistermacgray 3 жыл бұрын

You are welcome

@jeffreyrubish347 3 жыл бұрын

She's going good now.

@ProSaw70 Жыл бұрын

Quirky little saws these. Mine has been sitting in its plastic carry case untouched for too long. I’ll have to get into it.

@christophercollins2330 Жыл бұрын

I've got one of these that needs the same repairs. I have to coat the fuel tank first. I'll replace the fuel tank wicking as well. Nice work 👍thank you

@JoshuaAndMom Жыл бұрын

Got to love the Power Mac 6. These were much better made chainsaws back in the 70s. You sure can't buy quality like this anymore.

@michaelwhiteoldtimer7648 3 жыл бұрын

I LIKE TO WATCH THESE VIDEOS I AM JUST GLAD I DON'T HAVE TO FIX THEM

@mistermacgray 3 жыл бұрын

Thank you. I encourage....no challenge you to fix one. That is my message, get your hands dirty, learn something new.

@Thetreefella 3 жыл бұрын

Mister Mac Gray 💛🖤💛🖤

@AlBacore-bw2oo 2 ай бұрын

So, is this the correct order of the gaskets and diaphragms? Starting on the carb side and working out to the plate/fuel intake side: A) CARB SIDE 1) Gasket 2) Diaphragm B) WHITE PLASTIC CENTER PLATE 3) Gasket 4) Diaphragm C) ALUMINIUM PLATE/FUEL INTAKE SIDE If so, this might explain why my saw only runs on a prime. I believe I have 3 and 4 reversed. 😐

@redsoldierftcarson 3 жыл бұрын

Is it possible to cut the flange that holds that fuel line to the wick and adapt it to a modern barrel type filter?

@mistermacgray 3 жыл бұрын

Its a possibility

@michaelszpak2247 3 жыл бұрын

Bryan, What's the Mac part number for the fuel nipple. Thanks.

@mistermacgray 3 жыл бұрын

67581 is the part number

@MechanicShananigans 3 жыл бұрын

Does this have 1/4 pitch? And if so how long is the bar? Recently picked one up with a 14 in bar and a 1/4 sprocket but no chain. Needing info on how many Drive links I need

@mistermacgray 3 жыл бұрын

I think it's a 12 inch bar (cut area) but never really measured. I was told the bar is .043 gauge but if it may be .050. I was told that stihl dealerships have this chain onnhand and can spin a loop. You can also upgrade to 3/8 chain and use a mini mac clutch drum.

@MechanicShananigans 3 жыл бұрын

@@mistermacgray thanks for the quick reply, I would like to get some 1/4 chain since the sprocket and bar are in good shape, if they were toast I wouldn't be against a 3/8 swap

@mistermacgray 3 жыл бұрын

@@MechanicShananigans there is 3/8 chain thay will fit that bar, im sure whatever fits a mini mac will fit that.

@johndd8186 Жыл бұрын

Can you tell me where to get the rubber fuel connector? Thanks

@mistermacgray Жыл бұрын

Unfortunately not something that can be easily found. I use to have a spare one that i was going to copy and make new ones of but it's since long lost.

@SilverAlert1 3 жыл бұрын

Do you know of an aftermarket bar and chain set? I really want to get mine back 100%

@mistermacgray 3 жыл бұрын

Unfortunately I don't but these bars and chains are crazy common on ebay.

@stevengamsby5344 2 жыл бұрын

It goes gasket then the diaphragm and plastic was on them after 1974 before they where magnesium plus’s that’s a Chinese carb kit they’re always something messed up in them I’ve ordered hundreds of them my friend I’ve gotten them where they have two needles in them so good luck I haven’t finished watching it yet but I sent it to my dad and he laughed his ass off watching this lol

@ericfuller6326 17 күн бұрын

Whats bryan grays 2nd favorite saws? I love me a big poulan just got a nice 4200

@mistermacgray 17 күн бұрын

@ericfuller6326 anything with a 101 engine...if it's yellow and McCulloch...except the damn mini macs, trash those.

@ericfuller6326 17 күн бұрын

@@mistermacgray lol yeah i got 1 total it was a runner never worked on it. I was gonna get either a pow A pm 6 or this 4200. Probably a good idea but still need a pm6.

@mistermacgray 17 күн бұрын

@@ericfuller6326 pm6 or bust for a top handle mac saw.

@KJChaput 3 жыл бұрын

Where did you get that fuel line??? Those have been extinct for quite some time.

@mistermacgray 3 жыл бұрын

Ebay. One on there now for waaaay to much. Pretty much I stock up on parts now so when a saw comes my way I'm ready.

@tedmiller1745 Жыл бұрын

Hey brother, what is the part number for the rebuild kit? Thanks!

@mistermacgray Жыл бұрын

Walbro carburetor kit K1- MDC. The mini mac kits look similar but are not the same.

@tedmiller1745 Жыл бұрын

@@mistermacgray Thanks Bryan. Buddy bought one of these saws and took it apart and gave to me to get running.. I said why??? LOL. Time to see if the fuel connector is jacked and if the piston is ok then time to deal with this PITA saw. Thanks and great video...

@mistermacgray Жыл бұрын

@Ted Miller they are better than the mini macs, just have to find the hard to find fuel line and other than that, great saws.

@tedmiller1745 Жыл бұрын

@@mistermacgray Yea so I see. I will see if the fuel line goes in alright but wish I was the one who disassembled to check everything out...