This was so helpful. I was struggling finding a way to remove the cap and then the next piece to access the bolt. Thank you!

Great video Clear,direct and informational. So many repair videos are ego driven. I'm glad to say that I did not detect that here. Thank you

I can’t be thankful enough! Thank you so much for this video!

Thank you!!! I couldn't figure out why I couldn't put it together. I put the bolt in too early. Works like a charm now!!!

I like how you good at fixing all the equipment and any other stuff needs to be Fixed

I had a pillow cover stuck under the assembly. Thanks for helping me get it out.

thanks.... you have the easiest instructions!

Our washer's agitator bolt came loose. All I needed to know was how to remove the plastic cap to permit access to the bolt. Whirlpool customer support / tech support said I needed to have a technician visit ($89 just to show up at my door!). Not happening...just to re-install a bolt??? Called a local appliance repair shop to ask for help and they acted like I'd asked them to for the keys to the palace treasure vault. Found this video. Oh! You just pull it out? Mine was a little stuck, but the engineers at Whirlpool supplied me with three little "windows" in the side of the agitator where an appropriate sized screw driver leveraged the cap out sufficiently to remove it with my hand. Tightened down the bolt. Re-installed the cap. Life is good. Took my wife out to a nice lunch and still had $50 left over if I'd have called a technician. Thank you, AppliancePartsPros!

Thanks for the video showing the fixing.

Thanks to you for your informative solution,thank you very much.

Thank you thank you. My problem was scuzzy dirt collecting under the agitator that was getting on bedsheets. Parts of the sheets were getting drawn under the agitator and if I didn't catch it on the way to the dryer, the brown dirt was set in and it looked like s**t. Literally. Upon removing the agitator I expected a tub full of low tide in the salt marsh type of scenery, but was surprised by a nice clean white tub. The only dirty spot was a ring of slimy scuzzy crud about 6 inches up inside the agitator. Some spray cleaner and paper towels, all done. Thanks again. BTW, a small battery driven impact hammer works wonders getting the bolt loose. Start tightening the bolt with the ratchet then finish the job with the impact wrench. Easy peasy.

Thank you SO much!

This guy is the handiest man on you tube.

Thank You sooo much, for wanting to Help out others sometimes. 🙏🙂 My top part broke. Is an old Kenmore with only a flat cover on top. I called Sears ~ terrible experience !!!!!!! They 1st sent me the Top ONLY, without any parts !!! $99 !!! I called back and told them, she said (these were All foreign people) oh don't worry I Know what you need, tells me $106 !!!!!! I said for just little parts ?!?! Yes Ma'am,they are always so polite, bc half the time they don't know what you're talking about. Wow !!! No available parts places nearby anymore. Sooo, though I really didn't think that was Right, desperate, I paid. About a week later, big box, and very Small box came. She didn't just charge me, send Lil parts, she sent the bottom half of the agitator !!!!!!! Boy. Who knows what to do anymore. So cost me $200. Daughter said she probably could've found other washer on Marketplace. Anyway, I'm 70, had no idea what to do with this all. Told her that on phone she said no worries will send a how to video. Of course, she didn't. I decided to just keep it all and Hope something else doesn't break down in my Old washer, that's a lot of money for me on my own. Do you think it makes sense to keep that all, when all I really needed was the little parts ??? Sure would've been a whole lot cheaper !!!!!!! Anyway, in checking online for a how to, yours came up, and now I think I can do it🙂👍...Thank You much.

Great video, however I am having trouble getting the lower agitator to align back on to the spindle. Any advice?

Great video. Thanks a bunch 👍🏻.

I can’t get mine to lock in place! Any suggestions?

Is it necessary to have the agitator cap?

Can you add an agitator for the newer models without one? These new models without agitators will not clean clothes and leave detergent residue.

ok after the aggitator is off what or where do i go to get that special Tool to take the Drum completelly off ????? im working it now can you hammer with a screwdriver i have a wrilpool W10240509d -W10240510D .

If the agitator is wobbly on the top part is that a sign that its worn out and isnt it a good idea to change out the hub Too?

I took entire agitator out to replace dogs. Then when I put agitator back it stops while about 1" from bottom of tub. When I screw in bolt it stops at one point with out going into threads on washer shaft. There's nothing in the gears of agitator or threads on washer shaft. What happened?

I HAVE A QUESTION: i HAVE A MAGIC CHEF MODEL: CAV2004AWW BUT I CAN'T FIND A VIDEO THAT SHOWS ME HOW TO REPLACE THE AGITATOR. OR TO SHOW ME HOW TO REACH THE MOTOR OR MOTOR CLUTCH. THANKS I WILL APPRECIATE YOU FOR YOUR HELP NINO CROES

NO MATTER WHAT I do after removing the 7/16 bolt can I lift off the agitator assembly from the center spindle. It lifts up about an inch, and hits a hard stop and won't budge beyond that. (Electrolux/Frigidaire GLWS1749AS5)

I’m looking to replace the agitator on my washer with one that is less harsh on my clothes. The agitator is hard on my clothes

How to remove rop from agitato no bolt in center

Ok question.. mine spins with no problem but won't agitate.. the top part works fine. Teeth are all good and everything... HELP!

I’ve already replaced the whole agitator dog kit in my Maytag centennial washer but the bottom agitator base will not spin correctly while agitation mode is on

If you hold the lower agitator and the screw still spins, what should I do? When it first wasn't working it would freely spin and the bolt was loose. I tightened the bolt and it worked great. Now it won't agitate but the dogs are still engaging so i tried to tighten or loosen the bolt and it just spins even if I hold the lower agitator. Hmmmmm?????

Who does your hair? Luv it!❤

a button became stuck between the agitator bottom and the tub. The agitator spins freely. Will it cause any damage to the machine or should I remove the agitator and remove the shirt button?

I can't get the agitator assembly to go all the way down on the shaft. Please help.

How do you remove a stuck lower agitator?

Sir mera pas whirlpool white magic pro washing h washer dont working motor one side playing

I replace the agitator but still not washing properly

Hi replace the whirlpool washing machine but still not washing properly

Just because it is a cap you don't need a screwdriver for it you just lift it up

heres my prob ,the whole agitator comes right out ,the spline shaft comes out of the washer , is the shaft supposed to come out with the WHOLE agitator assembly ??? THIS WASHER IS A MAYTAG PERFORMA SERIES ,THANK YOU KINDLY !!!

How do you repair or remove the agitator when it is one of them little short ones that is down in the washing machine it is not a tall one like you showing the video can you please show me how to do this as I think that is what's wrong with mine

And with the bolt is stripped how do you take it off

1:04 or you are going to have the agitator cap where we will need to PULL IT OFF... NOT USE THE SCREWDRIVER...

U stand like a wrestler👍

line up locking clips?? how?? cant see anything

oh its called a Spanner Wrench

Nice, same as the web site that can't proofread their own directions and lame explanations before they put hem on the site making it seem like you are working with a dryer in your instructions rather than a washer. No short to the point reason for anything going wrong here either. like wtf causes this problem. what a load of crap!!!~! I dont see why some normal , not too far out of the way Human help would be too much to ask. PROS?" Hardly./ What happens when this part breaks: If you are in need of an agitator repair kit, your dryer may be experiencing a noisy agitator, or an agitator that spins freely in both directions. If your agitator is no longer agitating properly, your clothes will not tumble, and will not be washed properly. Where are the dryer agitator parts located? are they cheaper than the washer agitator parts?

Replace my no agitator to a agitator Whirlpool washing machine

Will not work with a Roper!!!!! The Roper is attached to the tub and when you try to turn the screw, the whole tub moves! But it works well with every other brand. SIGH 😔!!!!

1a