BGA Rework Reflowing Reballing for Absolute Beginners

BGA Rework Reflowing Reballing for Absolute Beginners - Tutorial Guide Part 1

Рет қаралды 38,303

Жыл бұрын

This is a new series looking at BGA Rework, Reflow and Reballing. It's primarily aimed at beginners who have never done this before, or those who have tried and failed to do it successfully . In part one we are going to discuss what reflowing and reballing actually mean, dispel a few myths and misinformation and then start by learning to desolder some small BGA chips (GPU RAM) and clean the PCB and Chip ready for reballing using basic equipment.
I work in collaboration with:
The Electronics Channel (live streams with Carlos and Detlef)
/ @theelectronicschannel
Gran Canaria Uncovered
/ @grancanariauncovered (with Detlef and Julie. Not electronics related)
Det Builds Stuff - / @detbuildsstuff8128 (Detlef)
Retro Upgrade - / @retroupgrade (Carlos)
For All Your PCB needs: free $5 discount coupon
www.pcbway.com/setinvite.aspx...
Equipment used in my videos. These are affiliate links, you pay the normal price and I make a small commission.
TEST METERS
Aneng AN8009
s.click.aliexpress.com/e/_DdW...
amzn.to/469ZgOS
www.banggood.com/custlink/mD3...
KM601
s.click.aliexpress.com/e/_DBw...
www.banggood.com/custlink/KD3...
VC480C+
s.click.aliexpress.com/e/_DEY...
amzn.to/3Q3LEz7
amzn.to/46tmNdo
MESR-100 ESR METER
amzn.to/3tiy8hK
amzn.to/3RwvejK
s.click.aliexpress.com/e/_Dmi...
XC6013L CAPACITOR METER
s.click.aliexpress.com/e/_DmX...
amzn.to/3t71Nul
amzn.to/3LDdcbO
TM-902C TEMPERATURE METER
s.click.aliexpress.com/e/_Dm9...
amzn.to/3LFzERv
amzn.to/3PTwuvW
LCR-T4 LOW COST COMPONENT ANALYZER
s.click.aliexpress.com/e/_Dmq...
www.banggood.com/custlink/KKK...
amzn.to/46uzV1R
amzn.to/3RHsmAN
FNB58 USB ANALYZER
s.click.aliexpress.com/e/_Dmd...
amzn.to/3tb1QW8
amzn.to/46oMn30
www.banggood.com/custlink/mKm...
PCI POST ANALYZER
s.click.aliexpress.com/e/_DBs...
amzn.to/46m9Gep
TL460S Plus PCI_E ANALYZER
s.click.aliexpress.com/e/_DnB...
amzn.to/3ZERvOs
TOOLTOP ET829 SCOPE METER
s.click.aliexpress.com/e/_DBw...
www.banggood.com/custlink/KGv...
MULTIMETER PROBE KIT KET05
s.click.aliexpress.com/e/_DE7...
OSCILLOSCOPES
FNIRSI 1014D
s.click.aliexpress.com/e/_DEz...
amzn.to/3RxMFk1
www.banggood.com/custlink/KKG...
FNIRSI DSO-TC3
s.click.aliexpress.com/e/_DC8...
amzn.to/3RBsgdS
www.banggood.com/custlink/Gm3...
FNIRSI DPOX180H
s.click.aliexpress.com/e/_DBX...
amzn.to/468oooT
www.banggood.com/custlink/GGG...
BENCH PSU
NPS3010W
s.click.aliexpress.com/e/_DDP...
amzn.to/3rxsuIf
www.banggood.com/custlink/3DD...
SOLDERING
T12 Station with M8 9501 Handle
s.click.aliexpress.com/e/_DFV...
amzn.to/3FdG8Ul
M8 9501 HANDLE
s.click.aliexpress.com/e/_De0...
T12-BC3 Tip
s.click.aliexpress.com/e/_DeN...
amzn.to/3EUFpqQ
amzn.to/3PB8axw
SUGON T26D
s.click.aliexpress.com/e/_DFx...
QUICK 861DW
s.click.aliexpress.com/e/_DDo...
amzn.to/3PBOKZH
amzn.to/3RCSqNh
PROS'KIT SS-331H
s.click.aliexpress.com/e/_DDo...
SS-331H Spare Parts
www.aliexpress.com/item/40002...
THERMAL CAMERA
Infiray P2 Pro
s.click.aliexpress.com/e/_Dmu...
amzn.to/457PgEb
www.banggood.com/custlink/DDG...
MICROSCOPES
Amscope Optical Microscope (copy)
s.click.aliexpress.com/e/_Dlh...
uk.banggood.com/custlink/mKGy...
amzn.to/4675Qp0
amzn.to/459uvrY
ANDONSTAR AD407
s.click.aliexpress.com/e/_Dl4...
amzn.to/3PSQKxJ
amzn.to/48sxej4
EEPROM Programming
TL866 II+
s.click.aliexpress.com/e/_Dls...
amzn.to/3RTCRB9
amzn.to/3LDu3Lu
CH341A
s.click.aliexpress.com/e/_Dk0...
amzn.to/48IZiir
1.8V ADAPTER
s.click.aliexpress.com/e/_Dci...
CONSUMABLES
NC-559-ASM FLUX
s.click.aliexpress.com/e/_Dda...
DESOLDER BRAID (I use size 8045)
s.click.aliexpress.com/e/_Dl5...
s.click.aliexpress.com/e/_DFJ...
MECHANIC HX-T100 Solder 63:37 (I use 0.6mm)
s.click.aliexpress.com/e/_DeZ...
ESD-11 TWEEZERS
s.click.aliexpress.com/e/_DCZ...
amzn.to/3PVfO7e
Learn Electronics Repair is now on Discord! Come and join the fun, it's free.
/ discord
If you would like to support this channel
You can send donations
www.paypal.com/paypalme/youtu...
You can subscribe to Patreon
/ learnelectronicsrepair
You can click Join to become a channel member
Thank you
Richard

Пікірлер: 65

@Ghost572 Жыл бұрын

Finally I have a reason for why people swurl their hot air guns around, I was thinking it was just pointless since the whole point is to get heat onto the chip, but heating the area is a good/valid point.

@1pcfred Жыл бұрын

I came here to learn how to be a baller.

@humbleyourego6053 Жыл бұрын

😂😂😂😂

@justalilred 6 ай бұрын

thank god for this video thank you for actually explaining

@techracoon7180 5 ай бұрын

These are some great tips, wish I have watched this video first and then attempt the fix. Thank you for always delivering such a good content.🎉

@maffysdad Жыл бұрын

Looking forward to part 2 of this one... Just so interesting...

@waCkyazn Жыл бұрын

Just found your channel its a great channel as I'm new to this type of repair and would like to learn more! thanks for your knowledge and sharing them

@tiiams Жыл бұрын

Awesome job don’t stop I’m still learning I could show what I did before your lesson learned a lot.

@nevergoingtoupload Жыл бұрын

Thank you for the video and your channel. Your channel was one of many that inspired me to pick up the soldering iron again and I am enjoying it. I am struggling though to get the memory chips down again after reballing and so I am waiting with interest to see your technique. The first TV's I repaired had valves in so it has changed a bit 😄

@LearnElectronicsRepair Жыл бұрын

Mark and Catherine C Yeah soldering them down again is also the hard bit - mostly because of getting enough heat transfer to the balls to do it The first TVs I repaired were also valve ones - I took my C&G in TV Radio and Electronics repair in the early 80s so we had to learn valve and semiconductor circuits. I actually consider myself luck to be formally trained in both 🙂

@Rolandpgbrooks 10 ай бұрын

Thank you so much for this video, im learning so much

@Umski Жыл бұрын

Thanks for the tips - been putting off replacing a medium sized BGA IC on an AV receiver that blew its lid from a rogue HDMI input ages ago - I’ve been soldering for 30+ years but never braved a hot air station (yet!) 😂

@xyzconceptsYT Жыл бұрын

Well done, methodical approach for beginners. Remember to practice on unimportant stuff if it works again you are winning. 😉 #righttorepair

@LearnElectronicsRepair Жыл бұрын

Exactly this ^^^

@willthecat3861 Жыл бұрын

agreed! ... but will they do it... sadly... no they won't.

@smarty0604 Жыл бұрын

Great informative video this pal

@edwinwaugh Жыл бұрын

Looking forward to part 2 😁

@DevilbyMoonlight Жыл бұрын

I'll finally get around to building a pre heater at some point, I got the old board and display from my CR10 left over after an upgrade for the logic as well as the thermistors and the display, I'll most likely use a halogen security lamp as the heat source with an SSR to switch the mains voltage, should be an easy build..

@Sydney268 Жыл бұрын

Nice work!

@ronan4681 Жыл бұрын

Agreed ... bring on part 2

@daz41262010 Жыл бұрын

great video Richard :)

@TristanVash38 8 ай бұрын

19:24 the 5 seconds before this, EXCELLENT TIP!

@MrPnew1 Жыл бұрын

I am glad that you said that "reflowing" the GPU in graphics cards like this is a myth. Only butchers do that crap. Good, informative video thanks.

@Lightrunner. Жыл бұрын

Hi, nice video. Reflow or desolder any bga is easyer with a preheater(i have the same🤗) Importen is to learn to take time for heating the pcb carefully. Otherwise bubbles will form on the pcb or bga I didn't have to learn that once😵‍💫. Painfully (rip pcb+bga 😢) As well the right tools are essential. A trick to save the soldier balls. Both, the pcb and the bga to tin with low melted lead. Voila👍 Who is the Part two of the video😳😎?

@Dutch_off_grid_homesteading Жыл бұрын

Heya never done BGA work at all it seems cool I'm thinking about giving it a try

@sipansibabdreddknot5179 Жыл бұрын

thanks for beginners tutorials on reflow,reball and rework kinda hard at first but needs more practice overtime to get things right but the tools needed would be a must investment first.

@LearnElectronicsRepair Жыл бұрын

Minimum tools required will be on part two

@RetroUpgrade Жыл бұрын

Nice demonstration of how important a preheat-er is :), i personaly use the heated bed on my 3d printer gets to around 80-100c

@shagreobe Жыл бұрын

I have an old 3d printer my brother gave me. I've been thinking of making something out of it, this seems perfect for it

@Pedro.Harruda Жыл бұрын

THANKS!!

@paulc0102 Жыл бұрын

I would say it's a mistake to assume that "bump gate" only affected nVidia. While it's true only they put their hands up (after a costly court loss) there's no evidence to suggest that any similar devices (e.g. from AMD) also manufactured by TSMC at the time *didn't* also suffer issues in the same order of magnitude. It was a fabrication not a design issue. Keep up the good work :)

@izzzzzz6 Жыл бұрын

I would try to reflow with the hot air station and flux before actually removing it and going through the entire polava of reballing. the balls are still there they just became dry joints, with flux they should melt back together with the hot air station.

@shaun4bigblocks993 4 ай бұрын

I don't know if it is fair to call it a "myth." Though not a "complete" fix it can make a good temporary fix. Back in those days I didn't have reballing equipment and did the oven trick 4 or 5 times over a 2-3 year period with sucess- long enough to get my money's worth out of my laptop until I had a technological excuse to upgrade. I also did this for family and friends. My guess is that as good as you are from a professional perspective, you probably have little experience from a halfazz perspective. Your way is better, but if outsouced usually comes with crazy fees, my way was free for people...

@Tech101yt 11 ай бұрын

Is it possible to accomplish a bga replacement without a board heater/thermocouple? The chip is removed successfully and the new chip is pre-balled, and I’ll be using a temperature controlled station. I’ve seen others using 220c for the same job

@davidv1289 Жыл бұрын

Very nicely done - thank you for showing us all the tricks. I wonder if the pre-heater thermostat is marked in degrees Fahrenheit 🤔.

@LearnElectronicsRepair Жыл бұрын

Actually it may well be 😉

@aldanimam9862 Жыл бұрын

nice

@roboandrew1 Жыл бұрын

Very useful. A very informative watch Can you possible do some with your big rework station to see if you can configure it for that kind of memory module or even a cpu socket replacment be an interesting watch

@LearnElectronicsRepair Жыл бұрын

Yes I will use that later in this series

@trouble_maker023 Жыл бұрын

I personally found reballing (apart from memory bank) always extremely daunting, it took me a long long time to get comfortable with it. Working with the classic lead free high melting point solder spheres is a pain, thus I am using Sn42Bi57Ag1 Solder spheres, they work like a charm. I should add that this alloy is very expensive compared to Leaded or standard lead free.

@Sydney268 Жыл бұрын

Just use ordinary 63/37 leaded balls - if you can remove a BGA with lead free balls, then you can replace it easier with leaded balls. Wouldn't trust that bismuth stuff on something that gets as hot as a GPU myself!

@trouble_maker023 Жыл бұрын

@@Sydney268 I’ve reballed memory and gpus, and I have yet to encounter problems, plus lead is very unhealthy

@mreaper2265 Жыл бұрын

@@trouble_maker023 lead is only a problem once it ends up on the scrapfields. Also the lower melt solder u reball with the sooner it will have to be done again. Not sure why its so difficult for you to reball with regular leadfree solder. It takes a few seconds on low heat and airflow. Will they not melt when you do it?

@Sydney268 Жыл бұрын

@@trouble_maker023 fair enough, but I'm sticking to the real stuff! I'm sure there are much worse nasties in the flux than lead, and although solder balls do look nice on cakes, I don't tend to eat them 🤣

@trouble_maker023 Жыл бұрын

@@Sydney268 well the only thing in lead is lead, that stuff is pretty nasty, but hey to each their own 🙌

@frankbennett8877 Жыл бұрын

Thanks for a great video. What flux do you use.

@LearnElectronicsRepair Жыл бұрын

Tools and all that will be on part two 😁

@Mr2Xri 21 күн бұрын

Hello, could you tell us the model of your reballing station?

@j44dge Ай бұрын

Alfie Solomons teaches reballing ;)

@Skipperc3po 2 ай бұрын

You use the hotair without noozle🤔

@HaploPrime Жыл бұрын

From what I was looking this up in the other resources they said not to put flux on all 4 corners or it'll create an air seal and not get under the BGA chip. Anyone know how true this is? I mean in theory sounds like it makes sense.

@mcac-youtube 6 ай бұрын

I think its not so important, The temperatura, the pre heater and enough time is more...

@David_11111 Жыл бұрын

yay where is part two :)

@LearnElectronicsRepair Жыл бұрын

I only just published part one, to test the water so to speak. Part two in the next few days

@evelhorn Жыл бұрын

I do it in a simular way, I find flipping it over and heating it up first then go at the chip. But what ever works

@willthecat3861 Жыл бұрын

IMO calling this 'reballing" is like calling like saying a trutle is a horse; because they both have four legs. Where's the solder balls, stencil, and jig? This is soldering... not reballing. Reballing is a complete PITA. Soldering these chips might work... as long as... you don't want it to last, don't flex the board, don't overheat the chip, don't flex on the heat sink... and know your lucky lottery number is about to pay off any day now.

@LearnElectronicsRepair Жыл бұрын

This is part one - you have to practice and learn how to get the BGA chip off the board without damaging either of them before you can move forwards. Part two we are going to look at required equipment and the limitations of it, and then part three will definitely involve some reballing. It takes time to practice and learn this stuff, let's not get ahead of ourselves 😉

@willthecat3861 Жыл бұрын

@@LearnElectronicsRepair Ok. Point taken. I guess I was getting ahead of myself. Looking forward to the other vids.

@willthecat3861 Жыл бұрын

IMO, U don't need the braid... and if you use it... you will lift a pad off of the PCB...eventually... and it won't be a 20 year old scap PCB, it happens to.

@LearnElectronicsRepair Жыл бұрын

What leads you to this opinion? Forget 'eventually' I used to lift pads off the PCB all the time when first using this technique until I learnt how to do it reliably by practicing using scrap stuff, and I then moved onto more worthwhile stuff once I gained some confidence and experience (thanks to some good advice and help from some guys on badcaps.net in particular) Now I very rarely lift pads using braid to clean the PCB and BGA, but I am always willing to learn to do things better, so how do you do it without braid?

@willthecat3861 Жыл бұрын

@@LearnElectronicsRepair Well... and perhaps it's not the best analogy...but, I used to watch high steel workers here... you know... incredibly skilled, and ultra-confident in the job they do: walking unlettered on high steel, hundreds of feet in the air.. and I always thought to myself, watching them... ya... I could do that too... after I fell a couple of times.