BitFenix - Nova Mesh M budget build for Lucky F*ck Masyn

Рет қаралды 1,523

Күн бұрын

builds.gg/phreakwarpc/bitfeni...
Find the Mllse Radeon RX 5500 XT here: amzn.to/3G8XphV
Find the AIO here: amzn.to/3SF2aHe
Find Lucky F*ck here: amzn.to/3QEdNeX
0:00 Intro
5:10 Parts
12:16 First Boot
14:10 Measure
17:44 Order of operation
18:46 RGB test
29:54 Stats
33:27 LUCKY F*CK Final reveal
38:00 Fortnite DX-12 Low
40:03 Fortnite DX-12 Medium
42:00 Fortnite DX-12 High
43:29 Fortnite DX-12 Epic

Пікірлер: 10

@Yo_Moneyy 4 ай бұрын

I have the same case and I don’t know where to plug in the cables from my aio cooler, I have my radiator up top and the cables from the fans going through the back

@thomasakrami558 3 ай бұрын

Wait so what do I do to change the colors of the fan

@peterprice2560 7 ай бұрын

The fan hub on the back has a sata connector, but it doesnt seem to match the sata connector on my power supply? Am I looking at it wrong or is there some cord I'm missing

@phreakwars 7 ай бұрын

The connector is on the bottom, the SATA cable from your PSU will plug in directly to the controller.

@ehrmantrout 4 ай бұрын

could you please tell me how to control the speed of these sock bitfenix fans? i have all them connected to the stock controller, then connected the 4 pin connector which controls the speed to the sys_fan_2 on my motherboard. and i still don't get how to control them.

@phreakwars 4 ай бұрын

Go into the BIOS of your board and set that PWM header to run in quiet mode and also make sure it's set to system not CPU. The controller should be picking up the PWM signal and lowering the fan speed.

@Yo_Moneyy 4 ай бұрын

Would either of you mind helping me? I’m like 75% done my pc with this exact case and an aio water cooler installed as well. I’m lost at where the aio cooler fan cables go as well as where the connector cables go or if they all connect together. Would be easier if I could email or message but YT comments are fine too

@ehrmantrout 4 ай бұрын

@@Yo_Moneyy connect pump to the CPU port, connect fans on aio radiators to the Pump Fan port(daisy chain them). these all ports are generally on top of a motherboard. connect your front panel fans if you are using them stock to the default connector on the back of a case, then insert the pwm connector to the sys_fan_1, it is also on top of the motherboard. also if you are planning on using rgb you should connect 3pin 5volts wire from the same default connector to the certain argb port on motherboard. it is recommended to have slightly positive pressure in a case so your PC doesn't work as a dust collector, hence you should make your front panel fans spin a bit faster than others. continuing the thought, you should connect your only back fan to the motherboard, NOT TO THE CONTROLLER, so you are able to make it spin slower than the front fans. of course you have a lot of connectors on the controller for argb, so this is your preference, just make sure you connected 3pin wire to the motherboard to argb port. and if you are struggling with rgb, by default it is controlled by "button on a case" which most people likely use for restarting the PC. this way, just rake something metal and hold it on the two pins of your connector, you'll find it.

@thomasakrami558 3 ай бұрын

Wait so what do I do to change the colors of the fan

@ehrmantrout 3 ай бұрын

@@thomasakrami558 lock with a screwdriver 2 pin connector on your controller at the back of the case. this turns fans from standard mode, to motherboard mode so you can control lights.