Building an Ooznest Original Workbee CNC: Electrical - 6. Assemble Duet Controller & Testing WorkBee

No video

Building an Ooznest Original Workbee CNC: Electrical - 6. Assemble Duet Controller & Testing WorkBee

Рет қаралды 3,829

Күн бұрын

I recently purchased an Ooznest Original Workbee CNC and in this series of videos I will be walking you through step by step on how to assemble it and get it up and running.
This is step 6 of the Electronics Assembly and Testing Your WorkBee
Chapters:
00:00 Introduction
00:54 6. Assemble Duet Controller
09:56 Testing Your WorkBee
If you would like to purchase a Workbee CNC from Ooznest please use my affiliate link below to support the channel.
ooznest.co.uk/...
Don't forget to visit my other social media:
Website - www.johnclothi...
Instagram - / johnclothieruk
Facebook - / johnclothieruk
Twitter - / johnclothieruk

Пікірлер: 29

@johnt9366 3 жыл бұрын

I watched the whole lot just for fun ..... and I really enjoyed them. Well done you

@JohnClothier 3 жыл бұрын

Thanks. Glad you enjoyed them

@stephenhardman344 3 жыл бұрын

Hi John - I have almost completed construction of a v2.3.1 1000mm x 1000mm WorkBee and have used your videos for guidance. I struggled with the Ooznest guides which are really accurate but not always easy to understand - your clearly explained videos made a BIG difference. I also contacted Ooznest for guidance and they are very helpful. Thank you:-)

@JohnClothier 3 жыл бұрын

Thank you ! I’m glad you found the videos useful

@airifixbuilds9873 3 жыл бұрын

VERY good videos keep it up

@JohnClothier 3 жыл бұрын

Thanks, will do!

@LG-ro5le 3 жыл бұрын

Just finished building my 1000X1500 workbee thanks to your videos! Found it much easier than following the written instructions ooznest provide. Thanks!

@JohnClothier 3 жыл бұрын

Thanks for letting me know. I’m glad you found it useful

@williamdaly7135 3 жыл бұрын

john, nice set of videos. I used them a lot to set up my Ooznest workbee 2.3, same size as yours. I found them really helpful to sort out problems where Ryan’s instructions weren’t so clear. Should be getting the computer programmed tomorrow and then hopefully on my way. Keep up the good work.

@JohnClothier 3 жыл бұрын

Thanks! I’m glad you found them useful.

@MakairaJim12 2 жыл бұрын

John. My Ooznest CNC will be arriving tomorrow, so you can only imagine how relieved I was to find your series on building the thing. Well done mate and Thank You! Although I haven't even started, I do want to try vertical mounts to be able to cut dovetails and other joints. Do you have any thoughts/experience with such a set-up? Although I'm not on Facebook I think I'l have to break the habit of a lifetime and join just for the Workbee group. Keep up the great work. Jim

@JohnClothier 2 жыл бұрын

Thanks. No I havent tried that yet

@AndyJenkins999 3 жыл бұрын

Well I am looking to buy one but I would have a watched for fun anyway. Good series John many thanks.

@JohnClothier 3 жыл бұрын

Thanks Andy. If you do, please consider using the referral link, would really appreciate it

@AndyJenkins999 3 жыл бұрын

@@JohnClothier certainly will John cheers.

@JohnClothier 3 жыл бұрын

Greatly appreciated

@astonite3488 2 жыл бұрын

Love the Workbee but hate the Duet it is a 3D Printer board hesitation about buying one at the moment

@Leighton2231 3 жыл бұрын

Nice one, thanks.

@JohnClothier 3 жыл бұрын

Thanks!

@TheSuperheimwerker 11 ай бұрын

Hi john just wanted to say thanks. Watched all videos to build my z1+ the Maschine is up but not running 😭next stop Facebook forum to try and get a connection to my laptop(proving DIFFICULT)

@JohnClothier 11 ай бұрын

Thanks. I’m glad it helped

@baboonman9018 3 жыл бұрын

Hi boss, I just pretty much completed a 1000 x 1000 Ooznest WB and found these videos very useful. I watched them for the build and used the Ooznest online 'manual' where things were a little less clear. A good job of work son and very much appreciated - may buy you a pint if we meet, cheers, Simon p.s. what v carve bits are you using and are they any good, S x

@JohnClothier 3 жыл бұрын

Thanks! I, glad you found the videos useful. I use the armana tools from ooznest and also some from Rennie tools.