Carnage - We Fit Cams To Trolvo... And It Goes Badly!

Рет қаралды 19,691

Күн бұрын

We hit a little setback while fitting the cams to the Trolvo, but we'll still make it to the Haltech Birthday Bash... probably!
If you wish to send the Carnage team fan mail, mail to:
Street Machine Carnage
73 Atherton Rd, Oakleigh
Victoria, 3166, Australia
Subscribe to Street Machine for V8-powered good times
secure.whichcar.com.au/street...
Street Machine is Australia’s number-one modified car magazine, bringing V8-powered good times since 1981.
We live for tough street cars, and the guys and girls who use them. Our channel features event coverage from all over Australia, including burnouts, drag racing, dyno competitions, show ’n’ shines and high-quality technical videos.
So follow along as we bring the magazine to life, and remember to check back regularly for new videos. www.streetmachine.com.au
Sign up to our free newsletter: www.whichcar.com.au/streetmac...
Facebook | streetmachinemagazine
Twitter | / streetmachine1
Instagram | / streetmachinemag
TikTok / streetmachinemag
Join the conversation: #streetmachinemag #streetmachinetv

Пікірлер: 203

@EnviXR81 2 жыл бұрын

That’s a tough break but you’re a champ for not covering up the stuff that goes wrong. Keep up the good work because you inspire some us to have a go.

@yoyobenjo1 2 жыл бұрын

Oh bugga expensive exercise there Scotty. Good ol Golbys to the rescue.

@michaelb5330 2 жыл бұрын

Good effort scotty Thanks for showing us just how easy this is to do Your honest about little errors is the best policy Thanks

@MrJermbob 2 жыл бұрын

Please note that you need to have the cams in the correct position lobe wise as they can open the valves in to the piston as you go down. Please notice this as you know piston 1 and 6 is at TDC do not allow the lobes to push the valves open on those cylinders as you do it up. You actually tighten all of the cam caps gently at the same rate so the cam goes down level with even pressure on all of the bearing faces.

@stoneshrink 2 жыл бұрын

when he talked about going to 10 nm my heart sank. you need to get the caps down, ideally a turn on each bolt so that it equally pushes it down, that said, had he ran it down with his electric wrench to where the bolt head just touches the cap, he'd likely have been fine. Ah well, I'm not throwing stones, I've been there and learned from it too.

@DrWashiE 2 жыл бұрын

Unless that cam is massive you have nothing to worry about on a 1JZ, they are a non-interference motor, but still good general advice.

@seanphilip8225 2 жыл бұрын

I always rotate the engine off TDC when installing after market cams and then align valve timing. If piston to valve has not already been checked.

@johnlloyd1028 2 жыл бұрын

Faaaark who hasnt done some thing similar when working on old cars! put it down to experience we will remember next time!

@adamashby6356 2 жыл бұрын

Oven cleaner gives the term rice burner a whole new meaning!

@letsallbe-friends1120 2 жыл бұрын

*The cam: "Oh, Snap!"* 😉 Well done for taking it in your stride Scotty. I'd've snapped a few other things if that'd happened to me! 😅😅

@DaveHiggoHiggins 2 жыл бұрын

Look at it this way, you have two very nice paper weights now. I hope you give one to Telfo for Christmas.

@stevenmarvo2620 2 жыл бұрын

Hey Scotty awesome channel.What you showed was real problems in building cars. Not these pay tv shows that get it perfect in an hour

@tedcain9577 2 жыл бұрын

Been having a bit of a rough run lately you poor bugger. Hopefully your luck turns around at the track.

@STREETMACHINETV 2 жыл бұрын

It does feel like that

@tedcain9577 2 жыл бұрын

I can see why. Everything works out in the end, If it hasn't worked out it's not the end. Good things are coming.

@doomslayermax 2 жыл бұрын

aww man when you showed the two peice cam my jaw dropped, guess whats a part of learning and good old goldie saving the day keep up the goood work scotty

@paulmartin3340 2 жыл бұрын

Ya should've just snapped the intake cam and called it a quad cam!! At least once again you were up front and didn't hide your stuff up Scotty. Cheers big fella. Sydney NSW.🇭🇲😁👍🦘🍺🍺🍺🦘👍😁🇭🇲

@PageUpPerformance 2 жыл бұрын

Ahh Scotty you poor bugger, how good are cars?! Loving the content mate, nice and raw and always honest! Makes us all feel better that we aren’t the only ones making blues and learning from them! If you’re not learning, you’re not alive! Keep up the great work brother👌🏼😎😍

@jrbuch 2 жыл бұрын

Also, I use Gerardo for my JZ work. He fitted 264/272 cams to my Soarer and by god did it wake it up!

@madmurf 2 жыл бұрын

Just what I like about this show you guys are always honest about stuff ups. It makes us back yard mechanics feel not so bad for doing similar things. 😁Keep that chin up its all still good to watch.👍

@CORNERSUNDERATTACK 2 жыл бұрын

He stuffs it up more often than not 🤣🤣 would be costing them/their sponsors a fortune

@gregmyatt9932 2 жыл бұрын

My heart stopped Scotty when I saw you pick half a cam up. I remembered doing that when I was an apprentice, it brought back some memories of my angry boss carrying on like a pork chop😂 And another thing I would do is bolt the sprockets on the cams and have them timed with marks lined up before you tighten the cams down.

@Mikki_Tu 2 жыл бұрын

OOPS, Scott run ALL of the bolts for one cam at a time down progressively and evenly, don't worry about torque until ALL bolts are already snugged down first.

@theimprovementsguy8871 2 жыл бұрын

Yup. Was thinking the same when he started talking about torquing them down lol. Damn

@nickannand3367 2 жыл бұрын

It's been a rough trott lately Scotty! Keeping at it is all you can do mate and you've been showing how things do fuck up sometimes and it's all part of it mate. I'll keep watching, the struggle will make it more satisfying when it does finally come together for you! I hope your family is well mate

@st8jkt69 2 жыл бұрын

Had me grimacing on the first cam cap

@anomamos9095 2 жыл бұрын

Tip Regardless of what the book says about tightening the cam caps LOOK at the lobes to see which are going to depress the valve stems and either do those nearby caps first or rotate the cam to match the book.

@gemini3558 2 жыл бұрын

Bugger !!! Dam hard luck Scotty !!! 😜👍🇦🇺

@MotoringBoxTV 2 жыл бұрын

Looked like you were just about ready to start using that half-cam as a weapon there Scotty 😅

@timlorenz9936 2 жыл бұрын

I feel like where alike Scotty. I'm pretty sure this would of happened to me mate. And yes we learn from our mistakes. keep up the great work.

@robberry1949 2 жыл бұрын

I am sure you're not the first and definitely won't be the last, amatuers learn by their mistakes Kudos to you for admitting it Scotty

@zachs8652 2 жыл бұрын

I’m with you on the way you put in cams this way and not that way haha. Gotta love pushrod engines scotty.

@wingoson 2 жыл бұрын

Hi Scotty, oven cleaner is great for cast iron, it can oxidise alloys badly, crc gasket remover spray works a treat for getting old gaskets off and any tough to remove grime. Hope this helps.

@ianbertenshaw4350 2 жыл бұрын

Also good on the BBQ ! Eats carbon off like nothing else !

@johnkirkilis34 2 жыл бұрын

The Trolvo should get into the nines Scotty with all that hard work. Shock of a sleeper. 👍😃❤️

@bradleyfelschow1270 2 жыл бұрын

i've always turned the motor off tdc so no pistons are at the top regardless of motor, then ran all bolts down to the cap about half a turn or so on them and then ran it through the sequences with the same amount of turns on each. a little more time consuming but it's allowed me to avoid doing this. unlucky tho man, happens to the best of us. hopefully the next cam you pay a bit more attention haha. keen to see the trolvo hit the strip again

@jimclarke1108 2 жыл бұрын

Scotty, if you run into any problems just drop it at the Volvo dealer ))

@sourwords1808 2 жыл бұрын

Scotty my jaw dropped when you lifted the cam and only half of it came out. Oh well, it happens. Doing great with the channel content 👍

@benni727 2 жыл бұрын

at least you guys show ya stuff ups. not like most others do

@HenryDarr 2 жыл бұрын

Wow didn't see that coming 😳

@gogetem188 2 жыл бұрын

HI JERRY the old Volvo make shore you were ya white terry toweling hat lol yerrrrrrr give ya good excuse lol love it

@philturner5385 2 жыл бұрын

Great video mate.

@Frontman936 2 жыл бұрын

Good for you man. Not having a whinge about the complexity of japanese cylinder heads but getting on with it. Love that this is one of those unique channels that gives love to cubes and boost.

@DodgyBrothersEngineering 2 жыл бұрын

Yeah I own a car with a 2JZ and before that an SR20 and have often wondered why they can make a head fit with the cams already installed. Would be so much easier to do everything on the bench and just slide it on. We should be thankful that Toyota didn't make him use a tool only available from Toyota.

@CORNERSUNDERATTACK 2 жыл бұрын

Complexity? 🤣🤣🤣🤣🤣🤣🤣🤣

@Frontman936 2 жыл бұрын

@@CORNERSUNDERATTACK yeah man it’s no Holden red motor

@honestpat7789 2 жыл бұрын

The simplicity in how you set tdc is genius-no degree wheel required Love to see how you do valve lift (obviously not on the trolvo) And, deez nutz 😂👌

@DodgyBrothersEngineering 2 жыл бұрын

A degree wheel isn't used to find TDC. A degree wheel is the used to find the cam lobe centre line of the cams relative to TDC so you can advance or retard the cam/s to set it to specification. You can use a deck bridge like Scotty used, measure through the spark plug hole if the head is on, or put a dial indicator on the rockers to find TDC, after using one of those methods you adjust the pointer on the degree wheel to zero to then use it for its intended purpose.

@ollyd4073 2 жыл бұрын

Aww man, that sucks! But, just imagine how many folks here will be saved from that exact mistake because you're not affraid to show the mishaps. Hope you get off struggle street and onto a track soon, definately earned it.

@DodgyBrothersEngineering 2 жыл бұрын

When you get this fired up I can wait to hear it idle. Say goodbye to engine vacuum. In the next episode of Carnage Scotty installs a vacuum reservoir so he has some brakes to stop with. I put 272 / 278 cams in my SR20 it had very little vacuum at idle. Although a lot of that came down to intake manifold as well.

@gavinb9627 2 жыл бұрын

Time to order a vacuum pump then Scotty

@beefcakeass 2 жыл бұрын

Good to see you tried the spray for the pistons, I recommended to you 6 months ago to use crc gasket stripper on the pistons as it does the same thing, bubbles up and wipes clean the carbon of pistons, not soo good on the iron deck though

@HazeyAuto 2 жыл бұрын

Get both halves of the cam gold plated and block mounted- there’s your winner and runner up trophies for the next Drag Challenge. Nothing gets wasted around here!

@GarageItYourself 2 жыл бұрын

Well shit, that sucks mate 😔 One thing I've learnt with these sorts of head are to tighten the caps down slowly over all the caps to keep the cams looking as level as possible. This spreads the valve spring loads nice n evenly and once all snugged down is when I creep up on the torque setting using the workshop manual.

@wobblysauce 2 жыл бұрын

You got that BT Ghost cam.

@harleyhem3381 2 жыл бұрын

Wow!! Never seen that happen before. Never had it happen either but i have always slowly tighten all the bolts down evenly couple turns at a time. I am also very curious tho as to why u didn't just lube the washer and nut up for the head studs and put them on the head studs before putting them down in the holes like a normal bolt? 🤔

@bunning63 2 жыл бұрын

Man, felt for you there brother. By the way, the five minute oven cleaner is the boom, you can be sneaky and use a hot air gun and heat the surface up a bit prior or yeah leave it for thirty minutes.

@gregorygeyer3634 2 жыл бұрын

My heart felt for you with the 2 piece cam. Maybe try one of those new SEMA Bluetooth cams. Chin up mate, keep looking forward.

@victorbitter583 2 жыл бұрын

Oops. After you snapped the cam and explained where you went wrong and how you will do it differently next time, I'm still not sure that you totally grasp the concept of where you went wrong and therefore (if so) are highly likely to do it again. The cap order is less important than the incremental aspect of the tightening sequence Each tome you turn one of the nuts that hold the cap on, It's important to only turn them 1 - 1.5 turns per stage until they bottom out and can then be torqued to spec Failing to do this will likely result in it happening again.. I used to reco heads for a living mate so take this advice or leave it. cheers.

@ericnelson6982 2 жыл бұрын

I was going to mention something of this nature. I would not get the torque wrench out until I drew them down evenly by hand. Keyword (evenly)

@duncanh6095 2 жыл бұрын

Yep, what he said. When i saw you had the tourqe wrench while all the caps were loose i was aware of what part of this went badly. You need to bring the cam down with all the caps, not just one or two.

@STREETMACHINETV 2 жыл бұрын

Went in fine the second time

@ericnelson6982 2 жыл бұрын

@@STREETMACHINETV That's great, I can't wait to see this thing rip. We all have bad days, Just regroup and get it done.

@victorbitter583 2 жыл бұрын

@@STREETMACHINETV You;re welcome. Not sure if you did it my way or not but either way, what i wrote was absolutely spot on. cheers Scotty.

@rbarmy3841 2 жыл бұрын

Scotty wind the bottom end half a turn so the pistons are far enough down the bore so you won't touch a valve on the top and snap one when doing up the cam caps

@STREETMACHINETV 2 жыл бұрын

That doesn't make sense. I mean the cams (when orientated correctly), valves and pistons have to align when the engine is at TDC, otherwise it wont go together

@nathanpeachs2704 2 жыл бұрын

What a legend Scotty 😄 Keeping it real eh😄🇭🇲

@briansavage6933 2 жыл бұрын

Loving this channel, thanks Scotty for showing everything warts n all. When I saw the video title I thought maybe you were going to have an issue with incorrect torque figures in the manual. I ran into that with a wrx quad cam engine, the caps go down to bugger all but the manual said twice the real spec for the end ones. Trap for the inexperienced. I was also worried we’d snap a cam too doing pretty much what you just did. We were lucky, the motor fired up right away with no issues. Looking forward to this thing hitting the track.

@mrwatthe 2 жыл бұрын

Oh man I feel for ya Scotty!

@bvward 2 жыл бұрын

Scott, on the plus side, you now have two Yaris exhaust cams... You'll get it sorted.

@lsgemini7686 2 жыл бұрын

Doesn’t this year just suck lol side note appreciate the shifter on the wall it didn’t go unnoticed 🤙🏼

@danielspencer1973 2 жыл бұрын

Well that happened 😳. Clearly you didn't hear me saying no no no wait Scotty! 🤣 Sometimes you have to learn what not to do. Still great content 👌

@MrJermbob 2 жыл бұрын

A magnet up the back of a deep socket while you start them by hand is the trick.

@john-1964 2 жыл бұрын

what a bummer, i feel for you bro, lets hope no more problems after this mishap .

@davidbarnsley8486 2 жыл бұрын

Bugger a slight understatement I didn’t think they broke that easy but I know nothing about this That is why I sent my broken engine to the engine builder and I just stuck it back in once it was all back together 👍👍👍

@jason2533 2 жыл бұрын

When I did the head gasket on my Landcruiser 1fzfe I was freaking out doing the cams as they are very long and easy to break. I was doing them as per workshop manual but I ended up doing up the cam caps bit by bit.

@ants3503 2 жыл бұрын

You Jinxed yourself mate 👍

@STREETMACHINETV 2 жыл бұрын

I really did

@stevenchandler4218 2 жыл бұрын

Awww! Krist Scotty does anything go right for you man..??

@stuli6007 2 жыл бұрын

I'm sure it's happened before but I've never witnessed a snapped cam on install. The video is called Carnage!

@threefiftyone4726 2 жыл бұрын

Thanks for not using clickbait in your titles. When you say it goes badly it really goes badly : ) Bummer

@pjromez 2 жыл бұрын

Very similar to when I did the head on the 1fzfe. The manual said to make sure particular lobes were facing down then do the caps in to out. I also found a vid by otramm in usa who shows do equal turns on each bolt, hopefully stops that happening :-(

@bretth3224 2 жыл бұрын

You need to slowly pull all the bolts down at the same time until the the cam and caps are sitting flush and then torque them up

@Broke4speed 2 жыл бұрын

Man...you guys are cursed. Love that you never give up though!

@hespie1 2 жыл бұрын

Bugger! New hybrid split cam edition.

@jenibond 2 жыл бұрын

OMG! you been busy boy scotty ! just about all the cars have work done !!! and first comment !!

@royferntorp3575 2 жыл бұрын

WMD Spray was awesome.

@felixmatt34 2 жыл бұрын

Cant wait to see it Scotty, you made the mistake so others dont have to

@gfam2023 2 жыл бұрын

Hey Scotty how’s a bloke get one of those lights. Looks bloody awesome

@jungofett 2 жыл бұрын

The Channel is living upto its name Scotty 🤣. Maybe you want to name it Less Carnage. Give yourself abit of a rest. I know Dad's ute took alot longer than expected but something about it makes it one of my favourite Carnage car. Hopefully with the Rona gone I'll get to see it up close some day.

@quincyoconnor9707 2 жыл бұрын

Had a woody moment

@craigritchie1933 2 жыл бұрын

Hay Scotty , don't forget the shims will most likely need re setting with a new camshaft

@almstlegalgarage2734 2 жыл бұрын

Gotta tighten your cam caps evenly scotty. Once their all seated then torque them to spec. Can’t just tighten one cap at a time while all that spring pressure pushing each side of the cam up. Mistakes happen and they can be costly but they are okay if you learn from them. Head up champ.

@davidfinn5029 2 жыл бұрын

Oh well shit happens. Only way we learn lol.. good luck with the next one

@IDGAF56852 2 жыл бұрын

You didnt get the oven cleaner out of the block holes around the pistons scotty?

@STREETMACHINETV 2 жыл бұрын

We neutralized it just fine

@MrJermbob 2 жыл бұрын

I know what that acid stuff is like to have a breath in and get the mist in your eyes. Its mental. Hahaha

@gavinb9627 2 жыл бұрын

Ok I am a complete novice with these engines, but my question is do the buckets need resizing? Basically adjust the valve lash? Bad luck Scotty, the perils of uncharted waters

@antonjimmy5636 2 жыл бұрын

So the ¾ race cam install didn't go well?

@terjejohnsen3651 2 жыл бұрын

Its aggressive cams i think it will work Just good. Now its interference engine for sure. How mutch hp do you think it gives?

@MafiaboysWorld 2 жыл бұрын

It's not that the Toyota head gasket is the best overall Scotty, but it's the best bang for buck. As Goleby himself said, 54psi before it goes pop....for something that costs $40-60 to replace. 👍 Any more boost, you may aswell go to a firering setup. 😎

@ayycee5303 2 жыл бұрын

If it takes 54 psi then it is the best you can get. Beyond that and you’re grout filling, forging and spending a fortune and head gasket costs are irrelevant

@MafiaboysWorld 2 жыл бұрын

@@ayycee5303 Nope. Titan does a gasket capable of holding well over 70psi, used in their 6sec drag cars over the past 20yrs, but it costs $550. Like I said, the Toyota is best bang for buck, but not best. 👍

@stevenkirk2563 2 жыл бұрын

Scotty you couldn’t feel it in the wrench before u applied more pressure?

@STREETMACHINETV 2 жыл бұрын

Nope

@mayhemracing7579 2 жыл бұрын

You are meant torque them in sequence. You still need to slowly tighten them evenly first. 🤦🏻

@holdenmad111 2 жыл бұрын

"Don't do what Scotty did" That's what she said too!

@dzitezracing 2 жыл бұрын

I was like, Surely you can't break a Cam.... Nekminit...

@alt7488 2 жыл бұрын

is that the old camera man from sick puppy adventures i heard?

@jamesheuston9959 2 жыл бұрын

Scotty was the tightining sequence to do 1 cam at a time and not to jump cam banks, Just just my thoughts Cheers mate sorry for misshap

@mrcasperjensen 2 жыл бұрын

Also make sure the cams are correct to crank… so you’re not trying to open a valve on a TDC piston

@nickl2548 2 жыл бұрын

All I can say is Bugger !

@robertwilson9012 2 жыл бұрын

Thanks for showing your mistakes - Scotty !!!!

@smithy2 2 жыл бұрын

Man Scotty i feel for you buddy, like they say; if its worth doing once, do it twice...

@CORNERSUNDERATTACK 2 жыл бұрын

I prefer “do it right the first time”

@wesgates5632 2 жыл бұрын

It's ok to cry.

@1993kawasaki 2 жыл бұрын

i thought you had to double triple CLICK the torque wrench just to make sure?!

@brad1674 2 жыл бұрын

Hey guys, any plans on doing anything with that Soarer behind the Trolvo? 🤙🏻

@STREETMACHINETV 2 жыл бұрын

The soarer is a donor car that were putting the engine in the Lexcen

@andrewbrown9460 2 жыл бұрын

Maybe you need to change the name of the show from “Carnage “ to “ works first time every time”. 👍 love the channel Scotty anyway.

@STREETMACHINETV 2 жыл бұрын

I like that. Or 95% of the time it works 100% of the time. :)

@jrbuch 2 жыл бұрын

Loved the Saddam Hussein reference, hahaha!

@kermitmotorsports6682 2 жыл бұрын

👍❤️😁

@justincummins166 2 жыл бұрын

Woody from Skid Factory did something similar, Benny and Al still give him shit about it.

@MafiaboysWorld 2 жыл бұрын

That's just 1 of the encyclopedia of reasons they give him shit. 🤣👍

@CORNERSUNDERATTACK 2 жыл бұрын

Woody is just as irritating…

@andyjames2082 2 жыл бұрын

Make sure you rinse all the caustic off, keeps eating away at stuff 👍

@STREETMACHINETV 2 жыл бұрын

Already done

@The_Performance_Laboratory 2 жыл бұрын

I hate that you continue to have crap luck, but I love that your show doesn't edit out all the problems... like they do on TV...

@mooroocho834 2 жыл бұрын

Fuck. We cant take you anywhere scotty 😆